Bsi bs en 01995 1 2 2004 na 2006

NA to BS EN 1995-1-2:2004

NATIONAL ANNEX

UK National Annex to
Eurocode 5: Design of
timber structures –
Part 1-2: General – Structural fire
design
ICS 13.220.50; 91.010.30; 91.080.20

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW


NA to BS EN 1995-1-2:2004
Publishing and copyright information
The BSI copyright notice displayed in this document indicates when the
document was last issued.
© BSI 2006
ISBN 0 580 49350 4
The following BSI references relate to the work on this standard:
Committee reference B/525/5
Draft for comment 05/30134000

Publication history
First edition, October 2006

Amendments issued since publication
Amd. no.

Date

Text affected


NA to BS EN 1995-1-2:2004

Contents
Introduction 1
NA.1
NA.2
NA.3
NA.4

Scope 1
Nationally Determined Parameters 1
Guidance on using informative annexes 2
Reference to non-contradictory complementary
information 3

Bibliography 4

Summary of pages
This document comprises a front cover, an inside front cover,
pages i and ii, pages 1 to 4, an inside back cover and a back cover.
â BSI 2006 ã

i


NA to BS EN 1995-1-2:2004

ii ã â BSI 2006

This page deliberately left blank


NA to BS EN 1995-1-2:2004

National Annex NA (informative) to
BS EN 1995-1-2:2004, Eurocode 5: Design of
timber structures – Part 1-2: General –
Structural fire design
Introduction
This National Annex has been prepared by BSI Subcommittee, B/525/5,
Structural use of timber. In the UK it is to be used in conjunction with
BS EN 1995-1-2 for the structural fire design of timber structures,
together with BS EN 1995-1-1, BS EN 1990 and BS EN 1991 and their
National Annexes.

NA.1 Scope
This National Annex gives:
a) the UK decisions for the Nationally Determined Parameters
described in the following subclauses of BS EN 1995-1-2:2004:
•

2.1.3(2)

•

2.3(1)P

•

2.3(2)P

•

2.4.2(3)

•

4.2.1(1)

b) the UK decisions on the status of BS EN 1995-1-2:2004
informative annexes;
c)

reference to non-contradictory complementary information.

NA.2 Nationally Determined Parameters
NA.2.1

Maximum temperature rise for separating
function in parametric fire exposure
[BS EN 1995-1-2:2004, 2.1.3(2)]
During the decay phase the temperature rise of the unexposed side of a
separating construction should be limited to the following:
a) average temperature rise (ΔΘ1) of 200 K;
b) maximum temperature rise (ΔΘ2) of 240 K.

NA.2.2

Partial factor for material properties in fire
[BS EN 1995-1-2:2004, 2.3(1)P]
The partial factor for material properties in fire, γM,fi, should be taken
as 1,0.

â BSI 2006

ã

1


NA to BS EN 1995-1-2:2004
NA.2.3

Partial factor for mechanical resistance of
connections in a fire situation
[BS EN 1995-1-2:2004, 2.3(2)P]
The partial factor for mechanical resistance of connections in a fire
situation, γM,fi, should be taken as 1,0.

NA.2.4

Reduction factor ηfi for combinations of actions
[BS EN 1995-1-2:2004, 2.4.2(3)]
The reduction factor for combinations of actions, ηfi, should be
evaluated using expression 2.9 of BS EN 1995-1-2, but is not permitted
to have a value less than 0,4.

NA.2.5

Procedure for determining cross-sectional
properties [BS EN 1995-1-2:2004, 4.2.1(1)]
The cross-sectional properties in fire should be determined using the
reduced cross-section method of 4.2.2.

NA.3 Guidance on using informative
annexes
NA.3.1

Parametric fire exposure [BS EN 1995-1-2:2004,
Annex A]
BS EN 1995-1-2:2004, Annex A should not be used.

NA.3.2

Advanced calculation methods
[BS EN 1995-1-2:2004, Annex B]
BS EN 1995-1-2:2004, Annex B should not be used.

NA.3.3

Load-bearing floor joists and wall studs in
assemblies whose cavities are completely
filled with insulation [BS EN 1995-1-2:2004,
Annex C]
BS EN 1995-1-2:2004, Annex C may be used.

NA.3.4

Charring of members in wall and floor
assemblies with void cavities
[BS EN 1995-1-2:2004, Annex D]
BS EN 1995-1-2:2004, Annex D should not be used.

2 ã â BSI 2006


NA to BS EN 1995-1-2:2004
NA.3.5

Analysis of the separating function of wall and
floor assemblies [BS EN 1995-1-2:2004,
Annex E]
BS EN 1995-1-2:2004, Annex E should not be used.

NA.3.6

Guidance for users of EN 1995-1-2
[BS EN 1995-1-2:2004, Annex F]
BS EN 1995-1-2:2004, Annex F may be used.

NA.4 Reference to non-contradictory
complementary information
Material from BS 5268, Structural use of timber
PD 6693, Complementary information for use with Eurocode 5,
BSI, London. (Publication date to be announced.)

â BSI 2006

ã

3


NA to BS EN 1995-1-2:2004

Bibliography
Standards publications
For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any
amendments) applies.
BS 5268, Structural use of timber
PD 6693, Complementary information for use with Eurocode 5
BS EN 1990:2002, Eurocode – Basis of structural design.
BS EN 1991 (all parts), Eurocode 1 – Actions on structures.
BS EN 1995-1-1:2004, Eurocode 5 – Design of timber structures –
Part 1-1: General – Common rules and rules for buildings.

4 ã â BSI 2006


NA to BS EN 1995-1-2:2004

This page deliberately left blank


NA to BS EN 1995-1-2:2004

BSI – British Standards Institution
BSI is the independent national body responsible for preparing British Standards.
It presents the UK view on standards in Europe and at the international level.
It is incorporated by Royal Charter.

Revisions
British Standards are updated by amendment or revision. Users of British Standards
should make sure that they possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using this
British Standard would inform the Secretary of the technical committee responsible,
the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures that
subscribers automatically receive the latest editions of standards.

Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: Standards are also
available from the BSI website at .
In response to orders for international standards, it is BSI policy to supply the BSI
implementation of those that have been published as British Standards, unless
otherwise requested.

Information on standards
BSI provides a wide range of information on national, European and international
standards through its Library and its Technical Help to Exporters Service. Various
BSI electronic information services are also available which give details on all its

products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111.
Fax: +44 (0)20 8996 7048. Email:
Subscribing members of BSI are kept up to date with standards developments and
receive substantial discounts on the purchase price of standards. For details of these
and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002.
Fax: +44 (0)20 8996 7001. Email:
Information regarding online access to British Standards via British Standards
Online can be found at />Further information about BSI is available on the BSI website at
.

Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of
the publications of the international standardization bodies. Except as permitted
under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,
stored in a retrieval system or transmitted in any form or by any means – electronic,
photocopying, recording or otherwise – without prior written permission from BSI.
This does not preclude the free use, in the course of implementing the standard, of
necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
written permission of BSI must be obtained.

389 Chiswick High Road
London
W4 4AL

Details and advice can be obtained from the Copyright & Licensing Manager.
Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: