Asme b16 32 1992 scan (american society of mechanical engineers)

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


~~

~~-

ASME B3b-32 9 2

m O759670 0533339

B30

m

AN AMERICAN NATIONAL STANDARD

Cast Copper Alloy
Solder Joint Fittings
For Sovent Drainage
Systems

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

ASME B16.32-I992
(REVISION OF ANSVASME B16.32-1984)

The American Society of
Mechanical Engineers
I

I
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

345 East 47th Street, New York, N.Y. 10017

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT

-


ASME E l b e 3 2 9 2

m

0759b70 053L3LIO 5 3 2

m

Date of Issuance: October 31, 1992

The 1992 edition of this Standard is being issued with an automatic addenda
subscription service. The use of an addenda allows revisions made in response to public review comments or committee actions to be published as
necessary; revisions published in addenda will become effective 6 months
after the Date of Issuance of the addenda, The next edition of this Standard
is 'scheduled for publication in 1997.

ASME issues written replies to inquiries concerning interpretations of technical
aspects of this Standard. The interpretations will be included with the above
addenda service. Interpretations are not part of the addenda to the Standard.

ASME is the registered trademark of The American Society of Mechanical Engineers.
This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards. The Consensus Committee that approved the code or standard
was balanced to assure that individuals from competent and concerned interests have had an
opportunity to participate. The proposed code or standard was made available for public review
and comment which provides an opportunity for additionatpublic input from industv, academia,
regulatory agencies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or
activity.
ASME does not take any position with respect to the validity of any patent rights asserted in
connection with any items mentioned in this document, and does not undertake to insure anyone
utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume
any such liability. Users of a code or standard are expressly advised that determination of the
validity of any such patent rights, and the risk of infringement of such rights, is entirely their own
responsibility.
Participation by federal agency representative(s) or, person(s) affiliated with industry is not to
be interpreted as government or industry endorsement of this code or standard.
ASME accepts responsibility for only those interpretations issued in accordance with governing
ASME procedures and policies which preclude the issuance of interpretations by individual volunteers,

No part of this document may be reproduced in any form,
in an electronic retrieval system or otherwise,
without the prior written permission of the publisher.
Copyright O 1992 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


ASME 816.32 92

m 0759670 0 5 3 3 3 4 3 479 m

FOREWORD

In the spring of 1920, the American Engineering Standards Committee (later successively named American Standards Association, United States of America Standards Institute, and American National Standards Institute) authorized the organization of a
Sectional Committee (later named Standards Committee) on the Standardization of Pipe
Flanges and Fittings for the purpose of unifying and further developing the flanged and
threaded fitting standards in force in this country. Designated as the joint sponsors were
the American Society of Mechanical Engineers (ASME), Heating and Piping Contractors
National Association (later named the Mechanical Contractors Association of America),

and the Manufacturers’ Standardization Society of the Valve and Fittings Industry (MSS).
Standards for solder joint fittings were originally developed by Subcommittee No. 11
of Sectional Committee A40, Minimum Requirements for Plumbing and Standardization
of Plumbing Equipment, organized in 1936 within the American Standards Association
(ASA). In 1949, responsibility for solder joint fittings was transferred to newly formed
Subcommittee No. 9 of Sectional Committee B16 on Standardization of Pipe Flanges and
Fittings.
The Sovent system for plumbing drainage systems was developed in Switzerland in
1961. Patent rights were obtained in late 1969 for the United States where the system
was finding use in high-rise developments. MSS developed and approved SP-74 in September 1970. A few months later, the MSS publication was submitted to Standards
Committee B16, which gave prompt approval to the proposal. The American National
Standards Institute (ANSI) granted approval on January 18, 1973. A revision adding
three dimensions for each fitting and including metric equivalents throughout was approved by ANSI in June 1979.
In June 1982, American National Standards Committee B16 became ASME B16 Standards Committee, operating with the same scope, under ASME procedures accredited
by ANSI. Subcommittee J (formerly 9) began a further revision of the standard in 1982
which resulted in editorial changes to the text and tables as well as an update of the
referenced standards. Following approval by Subcommittee J, the B16 Standards Committee and ASME, ANSI granted approval of the Standard on November 2, 1984.
This 1992 Edition of ASME B16.32 omits metric units, establishing US. customary
units as the standard. Changes were made in order to improve the text. Following approval by the B16 Standards Committee and ASME, approval as an American National
Standard was given on February 28, 1992, with the designation ASME B16.32-1992.
Requests for interpretations and suggestions for revision should be sent to the Secretary, B16 Committee, The American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, NY 10017.

@
iiii

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs

Not for Resale, 03/09/2014 04:35:47 MDT

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

(This Foreword is not a part of ASME 816.32-1992.)


ASME B l b . 3 2

72

W 0757670 0533342 305 W
~

ASME B I 6 COMMITTEE

Standardization of Valves, Flanges, Fittings, Gaskets, and Valve Actuators
(The following is the roster of the Committee at the time of approval of this Standard.)

OFFICERS
W. N. McLean, Chairman
R. A. Schmidt, Vice Chairman
J. Yarmush, Secretary

COMMITTEE PERSONNEL
W. L. Ballis, Columbia Gas Distribution Co., Columbus, Ohio
J. E. Batey, Union Carbide Corp., South Charleston, West Virginia
K. M. Bell, Underwriter's Laboratory, Inc., Northbrook, Illinois
M. L. Blair, US. Coast Guard, Washington, D.C.
R. R. Brodin, Fischer Controls International, Inc., Marshalltown, Iowa

W. G. Canham, Jr., Brentwood, Missouri
A. Cohen, Copper Development Association, Greenwich, Connecticut
W. C. Farrell, Jr., Stockham Valves and Fittings, Inc., Birmingham, Alabama
C. E. Floren, Mueller Co., Decatur, Illinois
D. R. Frikken, Monsanto Co., St. Louis, Missouri
M. W. Garland, Frick Co., Waynesboro, Pennsylvania
J. C. Inch, Mueller Brass Co., Hartsville, Tennessee
J. S. John, J Square Engineering Co., Houston, Texas
G. A. Jolly, Henry Vogt Machine Co., Louisville, Kentucky
W. G. Knecht, AnchorDarling Valve Co., Williamsport, Pennsylvania
R. Koester, William Powell Co., Cincinnati, Ohio
J. H. Longacre, Nibco, Inc., Elkhart, Indiana
J. H. McCauley, Jr., McCauley Mechanical, Chicago, Illinois
W. N. McLean, Chairman, Newco Valves, Palos Park, Illinois
A. F. Rhodes, Arnco Technology Trust, Houston, Texas
R. A. Schmidt, Vice Chairman, Ladish Co., Russellville, Arkansas
W. M. Stephan, Flexitallic Inc., Pennsauken, New Jersey
T. F. Stroud, Ductile Iron Pipe Research Association, Birmingham, Alabama
R. E. White, Repairs, Inc., South Bend, Indiana
D. A. Williams, Southern Company Services, Birmingham, Alabama
D. Wilson, Mobile Pipeline Co., Dallas, Texas

-

SUBCOMMITTEE J
COPPER AND COPPER ALLOY FLANGES, FLANGED
FITTINGS, AND SOLDER JOINT FITTINGS
J. H. Longacre, Chairman, Nibco, Inc., Elkhart, Indiana
A. M. Nickles, Secretary, ASME, New York, New York
A. Cohen, Copper Development Association, Greenwich, Connecticut

D. R. Frikken, Monsanto Co., St. Louis, Missouri
R. C. Haenke, Mueller Brass, Co., Port Huron, Michigan
M. E. Holmgren, Elkhart Products Corp., Elkhart, Indiana
D. Blankinship, Lee Brass Company, Anniston, Alabama
V

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


ASME Blb.32

92 W 0759b70 05333q3 241

CONTENTS

...............................................................................

Foreword
Standards Committee Roster

1
2
3

4
5
6

7
8
9

.........................................................

...........................................................................
.....................................................................
............................................................................
............................................................................
....................................... ................................
........................................................................

Scope
Description
Pitch
Sizes
Marking
Material
Metal Thickness
Design Features
Tests

................................................................
................................................................

............................................................................

Figures
1
Designation of Openings of Aerator Fittings

2
3

4

.................................
..............................
.................................................................
..............................................................

Designation of Openings of Deaerator Fittings
Aerator Fitting
Deaerator Fitting

Tables
1
Dimensions of DWV Sovent Aerator Fittings
Dimensions
of Pressure Equalizing Connections on Sovent
2
3

................................

Aerator Fittings .............................................................
Dimensions of DWV Sovent Deaerator Fittings .............................

Annex

A

References

.....................................................................

vii

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT

iii

v

1
1
1
1

1
1

1
1
2

3

3

4
5

6
7
7

9


-

~

ASME 816.32 9 2

m

0759b70 0533344 188

m

ASME B16.32-1992

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR SOVENT DRAINAGE SYSTEMS

O

O

1 SCOPE

4 SIZES

1.1 General

(u) The size of the fittings shown in the following
tables corresponds to the drainage tube size shown
in ASTM B 306.
.(b) Fittings are designated by the size of the opening in the sequence illustrated in Figs. 1 and 2.

This Standard for cast copper alloy solder joint
DWV (Drain-Waste-Vent) fittings used on self-aerating one pipe Sovent systems covers the following:
(u) description
(b) pitch
(c) Sizes and methods of designating openings for
reduced fittings
(d) marking

(e) material
v) metal thickness
(¿TI design
(h) tests

5 MARKING

Each fitting shall be marked permanently and legibly with the manufacturer’s name or trademark and
with DWV SOVENT.

6 MATERIAL

1.2 Units of Measurement

Castings shall be copper alloy, produced to meet
either
(u) the requirements of ASTM B 62 Alloy C83600,
or
(b) the chemical and tensile requirements of
ASTM B 584 Alloy C83800 or C84400;
and in all other respects, the requirements of ASTM
B 62.

U.S. customary units are the standard. For conversion to metric SI units, 1in. = 25.4 mm (not applicable to drainage tube size).

2 DESCRIPTION

O

(u) These fittings are designed to perform hydraulically and pneumatically under full fixture load

in buildings utilizing the self-aerating one pipe (Sovent) system.
(b) Manufacturers are cautioned that configurations shown in Figs. 3 and 4 are critical and are based
on careful testing. The dimensions specified herein
shall govern in all cases.
(c) All connections listed herein shall be female
solder joint fitting ends made to receive copper tube
diameter and conform to Table 1 of ASME B16.23.

7 METAL THICKNESS

Dimensional variations may occur in the casting
process. Pattern equipment shall be designed to produce the metal thickness given for fittings in Table l
of ASME B16.23. Any final fitting metal wall thickness less than 90% of the thickness given in the table
is unacceptable.

8 DESIGN FEATURES
3 PITCH

(a) The liquid or air flow area on either side of
baffle Q (see Fig. 3) in the aerator fitting shall not
be less than the cross-sectional area of the nominal
tube size of the main line.

All nominal 90 deg. drain openings shall be pitched
to result in a downward slope of in./ft (2.1%) as
shown in Fig. 3.
1

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


__

~~

ASME 816.32 92

~~

m 0759670 0533345 O34 m
CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR COVENT DRAINAGE SYSTEMS

ASME 816.32-1992

(b) Aerator fitting with double soil entries shall
have baffle P (see Fig. 3).
(c) Alternate Design.The top part of the offset portion of the aerator fitting may utilize a cast 45 deg.
street elbow with nominal size radii on NPS 3 and 4
fittings (4 in. R for size 4, 3 in. R for size 3; see Fig.
3). Elbows with shorter than nominal size radii on
sizes 3 and 4 will not suffice for reasons other than
strength. Care must be taken to ensure that entry

elbow is in line with the outlet portion of the fitting.
(d) The cross-sectional area (see Fig. 4) opposite
the baffle (flow area) on the deaerator fittings shall
be from 1.2 to 1.4 times the nominal tube size.
9 TESTS

Each fitting shall be subjected to a hydrostatic
pressure of 25 psig. The fitting &all not leak water
nor sweat at any part of the surface. Alternative tests
that demonstrate the same degree of soundness and
strength may be substituted for the hydrostatic pressure test.

2
--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


ASME 816.32 92

m 0759670 0533346
~

T50

m

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR COVENT DRAINAGE SYSTEMS

ASME 816.32-1992

GENERAL NOTE.
T o determine whether inlets are left or right, place aerator fitting in upright vertical position with face
inlet surface turned toward you. The side on which the other inlet appears determines its designation.

FIG. i DESIGNATION OF OPENINGS OF AERATOR FITTINGS

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Pressure
relief outlet

FIG. 2

DESIGNATION OF OPENINGS OF DEAERATOR FITTINGS
3

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT

A S I E B36.32 92 M 0 7 5 9 6 7 0 0 5 3 3 3 4 7 997

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR SOVENT DRAINAGE SYSTEMS

ASME 816.32-1992

On alternate deslgn
using 45 deg. street
elbow [see para. (8)]

For pressure equalizing
line (PEL) optional

A

\

r\
Baffle P y

t

4

Ø-

f

Pitch'"

FR

t

i
I

Pitch"'

I

i-

/

'fie

-7

Pitch"'

NOTE:
(1) Reference Section 3, Pitch

FIG. 3

AERATOR FITTING
4

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT

Q


a

~~

ASME B 3 b - 3 2 92 W 0 7 5 9 6 7 0 0533348 823 H
~

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR COVENT DRAINAGE SYSTEMS

ACME 816.32-1992

I

A

FIG. 4

DEAERATOR FITTING

5
--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


O759670 0533349 7bT

ASME B L 6 . 3 2 7 2

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR COVENT DRAINAGE SYSTEMS

ASME 816.32-1992

o o w ( D w 0

9hleJmmmm

x x x x x x

9)"

NCJ"

x x x x x x

9NN"hl(V
x x x x x x
59mNbm*LD

x x x x x x
BmN*m*u,

x x x x x x
Bmm* * m a

x x x x x x
3mme*LDw

6
--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


A S I E B36.32 92 E 0759b70 0533350 483 E

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR SOVENT DRAINAGE SYSTEMS

TABLE 2

DIMENSIONS OF PRESSURE EQUALIZING CONNECTIONS ON
SOVENT AERATOR FITTINGS (See Fig. 3)
Size
I
S
I
T
I Nominal Size Opening
~~~

~

3
3
4
4
5
6

X
X
X
X
X

3
3
4
4
5
x

X 3
X 2
X 4
X 3
X 4
6

ASME 616.32-1992

X
X
X
X
X
~

~

3
2
4
3

4

~~

X
X
X
X
X
5

2
2
2
2
2

X
X
X
X
X
~

2 X
2 X
2 X
2 X
2 X
5

2
2
3
3
3
~

2

~

1.59
1.59
2.25
2.25
1.62
21.35~

3

1.19
1.19
1.62
1.62
2.22
2.73

1Y2 DWV
1% DWV

1% DWV
1% DWV
1”’ DWV
2 DWV

GENERAL NOTE: Dimensions are in inches.

TABLE 3
Size

DIMENSIONS OF D W SOVENT DEAERATOR FITTINGS
(See Fig. 4)
A

B

C

D

E,
deg.

F

G

H

0.63

0.69
0.91
0.88
0.94

7.63
9.55
11.50
13.88
16.81

2.94
4.22
4.38
5.47
5.75

3.41
4.63
5.38
5.97
6.75

35
30
35
30
30

2.47

3.25
4.31
5.94
6.9?

0.25
0.25
0.25
0.25

1.66
2.13
2.69
2.69
3.22

0 0 0
3
4
5
5
6

X 3 X
X 4 X
X 5 X
X 5 X
x 6

2

3
3
4
~ 4

. . I

GENERAL NOTE: Dimensions are in inches except as indicated.
NOTE:
(1) See Fig. 2 for location of designated size dimensions.

7

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


k

ASME BLb.32 92

m

0759670 0533353 318

m

~

CAST COPPER ALLOY SOLDER JOINT FITTINGS
FOR SOVENT DRAINAGE SYSTEMS

ASME 616.32-1992

ANNEX A

REFERENCES
(This Annex is an integral part of ASME B16.32-1992and is placed after the main text for convenience.)

The following is a list of standards and specifications referenced in this Standard
showing the year of approval.
ASME Publications (Approved as American National Standards)

ASME B16.23-1990

Cast Copper Alloy Solder Joint Drainage Fittings
DWV

-

ASTM Publications

ASTM B 62-86

Specification for Composition Bronze or Ounce Metal
Castings

ASTM B 306-88

Specification for Copper Drainage Tube (DWV)

ASTM B 584-90b

Specification for Copper Alloy Sand Castings for
General Applications

Publications of the following organizations appear on the above list:
ASME

The American Society of Mechanical Engineers
345 East 47th Street, New York, NY 10017

ASTM

American Society for Testing and Materials
1916 Race Street, Philadelphia, PA 19103

Publications appearing above which have been approved as American National
Standards may also be obtained from:

ANSI

American National Standards Institute, Inc.
11West 42nd Street, New York, NY 10036

9
--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT


A S I E B36.32

92

0759670 0533352 254 9

AMERICAN NATIONAL STANDARDS
PIPE FLANGES. FITTINGS. AND

FOR PIPING.
VALVES

............................................

Scheme for the Identification of Piping Systems
A13.1-1981(R1985)
Pipe Threads. General Purpose (Inch)
81.20.1-1983(R1992)

Dryseal Pipe Threads (Inch)
61.20.3-1976(R1991)
Cast Iron Pipe Flanges and Flanged Fittings
616.1-1989
Malleable Iron Threaded Fittings. Class 150 and 300
816.3-1985
Cast Iron Threaded Fittings. Classes 125 and 250
816.4-1985
Pipe Flanges and Flanged Fittings
816.5-1988
Factory-Made Wrought Steel Buttwelding Fittings
816.9-1986
Face-to-Faceand End-to-End Dimensions of Valves
816.10-1986
Forged Fittings. Socket-Welding and Threaded
816.11-1991
Cast Iron Threaded Drainage Fittings
816.12-1991
Ferrous Pipe Plugs. Bushings. and Locknuts with Pipe Threads
816.14-1991
Cast Bronze Threaded Fittings. Class 125 and 250
816.15-1985
Cast Copper Alloy Solder Joint Pressure Fittings
816.18-1984
Ring-Joint Gaskets and Grooves for Steel Pipe Flanges
816.20-1973
Nonmetallic Flat Gaskets for Pipe Flanges
816.21-1992
Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
816.22-1989

Cast Copper Alloy Solder Joint Drainage Fittings - DWV
816.23-1992
Cast Copper Alloy Pipe Flanges and Flanged Fittings. Class 150. 300.400.600. 900.
816.24-1991
1500. and 2500
Buttwelding Ends
816.25-1986
Cast Copper Alloy Fittings for Flared Copper Tubes
816.26-1988
Wrought Steel Buttwelding Short Radius Elbows and Returns
816.28-1986
Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV
816.29-1986
816.32-1992
Cast Copper Alloy Solder Joint Fittings for Covent Drainage Systems
Manually Operated Metallic Gas Valves for Use in Gas Piping Systems Up to 125 pslg
(Sizes '/2 Through 2)
616.33.1990
Valves Flanged. Threaded. and Welding End
616.34-1988
Orifice Flanges
816.36.1988
Large Metallic Valves for Gas Distribution (Manually Operated. NPS 2Y2 to 12. 125 psig Maximum)
B16.38-1985
Malleable Iron Threaded Pipe Unions. Classes 150. 250. and 300
816.39-1986
Manually Operated Thermoplastic Gas Shutoffs and Valves in Gas Distribution Systems
816.40-1985
Functional Qualificatlon Requirements for Power Operated Active Valve Assemblies
for Nuclear Power Plants

816.41-1983(R1989)
Ductile Iron Pipe Flanges and Flanged Fittings. Class 150 and 300
616.42-1987
Wrought Copper and Copper Alloy Solder Joint Fittings for Sovente Drainage Systems
B16.43-1982
Cast Iron Fittings for Sovent? Drainage Systems
616.45-1987
Large Diameter Steel Flanges (NPS 26 Through NPS 60)
816.47-1990
Power Piping
831.1-1989
Fuel Gas Piping
831.2-1968
Chemical Plant and Petroleum Refinery Piping
831.3-1990
Liquid Transportation Systems for Hydrocarbons. Liquid Petroleum Gas.
Anhydrous Ammonia. and Alcohols
631.4-1989
Refrigeration Piping
631.5-1987
Gas Transmission and Distribution Piping Systems
831.8-1989
Building Services Piping
831.9-1988
Slurry Transportation Piping Systems
831.1 1-1989
ASME Guide for Gas Transmission and Distribution Piping Systems - 1986 (not an ANSI Standard)
Manual for Determining the Remaining Strength of Corroded Pipelines (not an ANSI Standard)
B31G-1991
Welded and Seamless Wrought Steel Pipe

836.10M-1985
Stainless Steel Pipe
836.19M-1985
Self-operated and Power-Operated Safety-Related Valves Functional Specification Standard
N278.1-1975(R1984)

....................................................
..............................................................
.......................................................
...............................................

..................................................

................................................................
.................................................
..............................................
...................................................
............................................................
....................................

................................................
.................................................
...........................................
.......................................................
.................................
.........................................
............................................................................
..............................................................................
..............................................
.....................................

................
..............................

-

.......................................................................
..................................................
................................................................................

.................................................
..........................................
...................................................................................
.................................................................................
....................................................
..........................................................
.............................................................................
................................................
.........................................................................

...........................................................

.............

.......
.....................................................

..........................................................................

..

.

The ACME Publications Catalog shows a complete list of all the Standards published by the Society
For a complimentary catalog. or the latest information about our publications. call 1-800-THE-ASME
(1.800.843.2763)

.

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT

--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

...
..................................
.............
............................................................
.................................
.............


--`,`,,,,,`,``,,,``,,,`,,`,``,`-`-`,,`,,`,`,,`---

Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS

Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
Not for Resale, 03/09/2014 04:35:47 MDT