Bsi bs en 62343 3 1 2016

BS EN 62343-3-1:2016

BSI Standards Publication

Dynamic modules

Part 3-1: Performance specification
templates — Dynamic channel equalizers

BS EN 62343-3-1:2016 BRITISH STANDARD

National foreword

This British Standard is the UK implementation of EN 62343-3-1:2016. It is
identical to IEC 62343-3-1:2016. It supersedes BS EN 62343-3-1:2010 which
is withdrawn.

The UK participation in its preparation was entrusted by Technical
Committee GEL/86, Fibre optics, to Subcommittee GEL/86/3, Fibre optic
systems and active devices.

A list of organizations represented on this committee can be obtained on
request to its secretary.

This publication does not purport to include all the necessary provisions of
a contract. Users are responsible for its correct application.

© The British Standards Institution 2016.
Published by BSI Standards Limited 2016

ISBN 978 0 580 90819 4

ICS 33.180.20

Compliance with a British Standard cannot confer immunity from
legal obligations.

This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 31 August 2016.

Amendments/corrigenda issued since publication

Date Text affected

EUROPEAN STANDARD BS EN 62343-3-1:2016
NORME EUROPÉENNE
EUROPÄISCHE NORM EN 62343-3-1

ICS 33.180.20 July 2016

Supersedes EN 62343-3-1:2010

English Version

Dynamic modules - Part 3-1: Performance specification
templates - Dynamic channel equalizers
(IEC 62343-3-1:2016)

Modules dynamiques - Partie 3-1: Modèles de spécification Dynamische Module - Teil 3-1: Vorlagen für
de performance - Egaliseurs de canaux de transmission Leistungsspezifikationen - Dynamische Kanal-Equalizer
dynamiques
(IEC 62343-3-1:2016) (IEC 62343-3-1:2016)

This European Standard was approved by CENELEC on 2016-05-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62343-3-1:2016 E

BS EN 62343-3-1:2016

EN 62343-3-1:2016

European foreword

The text of document 86C/1370/FDIS, future edition 2 of IEC 62343-3-1, prepared by
SC 86C “Fibre optic systems and active devices” of IEC/TC 86 “Fibre optics” was submitted
to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62343-3-1:2016.

The following dates are fixed:

• latest date by which the document has to be (dop) 2017-02-26
implemented at national level by (dow) 2019-05-26
publication of an identical national
standard or by endorsement

• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes EN 62343-3-1:2010.

It constitutes a technical revision and includes the following significant technical change with respect
to the previous edition:

– modification of terms and definitions and references.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice

The text of the International Standard IEC 62343-3-1:2016 was approved by CENELEC as a

European Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated :

IEC 61300 (series) NOTE Harmonized in EN 61300 (series).

IEC 61753-1 NOTE Harmonized as EN 61753-1.

2

BS EN 62343-3-1:2016

EN 62343-3-1:2016

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:

www.cenelec.eu.

Publication Year Title EN/HD Year

IEC 61300-2-14 - Fibre optic interconnecting devices and EN 61300-2-14 -

passive components - Basic test and

measurement procedures -- Part 2-14:

Tests - High optical power

IEC 61300-3-2 - Fibre optic interconnecting devices and EN 61300-3-2 -

passive components - Basic test and

measurement procedures - Part 3-2:

Examination and measurements -

Polarization dependent loss in a single-

mode fibre optic device

IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -

passive components - Basic test and

measurement procedures -- Part 3-6:

Examinations and measurements - Return

loss

IEC 61300-3-29 - Fibre optic interconnecting devices and EN 61300-3-29 -

passive components - Basic test and

measurement procedures -- Part 3-29:

Examinations and measurements -

Spectral transfer characteristics of DWDM

devices

IEC 61300-3-32 - Fibre optic interconnecting devices and EN 61300-3-32 -

passive components - Basic test and

measurement procedures -- Part 3-32:

Examinations and measurements -

Polarization mode dispersion

measurement for passive optical

components

IEC 61300-3-38 - Fibre optic interconnecting devices and EN 61300-3-38 -

passive components - Basic test and

measurement procedures - Part 3-

38:Examinations and measurements -

Group delay, chromatic dispersion and

phase ripple

IEC 61753-021-2 - Fibre optic interconnecting devices and EN 61753-021-2 -

passive components performance standard

-- Part 021-2: Grade C/3 single-mode fibre

optic connectors for category C -

Controlled environment

IEC 62343 - Dynamic modules - General and guidance EN 62343 -

ITU-T - Spectral grids for WDM applications: - -

Recommendation DWDM frequency grid

G.694.1

3

– 2 – BS EN 62343-3-1:2016
IEC 62343-3-1:2016 © IEC 2016

CONTENTS

FOREWORD.........................................................................................................................3
INTRODUCTION ................................................................................................................... 5
1 Scope............................................................................................................................6
2 Normative references.....................................................................................................6
3 Terms and definitions ....................................................................................................7
4 Test report.....................................................................................................................7
5 Reference components ..................................................................................................7
6 Performance requirements .............................................................................................7

6.1 Dimensions ...........................................................................................................7
6.2 Sample size ..........................................................................................................7
6.3 Test details and requirements................................................................................7
Bibliography .......................................................................................................................10

Table 1 – Tests and requirements .........................................................................................8

BS EN 62343-3-1:2016 – 3 –
IEC 62343-3-1:2016 © IEC 2016

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________

DYNAMIC MODULES –

Part 3-1: Performance specification templates –
Dynamic channel equalizers

FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 62343-3-1 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.

This second edition cancels and replaces the first edition published in 2010. This edition
constitutes a technical revision.

This edition includes the following significant technical change with respect to the previous
edition:

– modification of terms and definitions and references.

– 4 – BS EN 62343-3-1:2016
IEC 62343-3-1:2016 © IEC 2016

The text of this standard is based on the following documents:

FDIS Report on voting
86C/1370/FDIS 86C/1372/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

A list of all parts in the IEC 62343 series, published under the general title Dynamic modules,
can be found on the IEC website.

The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "" in the data
related to the specific publication. At this date, the publication will be

• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

A bilingual version of this publication may be issued at a later date.

BS EN 62343-3-1:2016 – 5 –
IEC 62343-3-1:2016 © IEC 2016

INTRODUCTION

A dynamic channel equalizer (DCE) is used to compensate and equalize the variations in
channel power spectrum as the optical channels propagate through DWDM networks. A
typical DCE module is an electrically controlled two port device, which controls the time
varying power levels of multichannel input signals such that, at the output channel, powers
are nominally equalized.

– 6 – BS EN 62343-3-1:2016
IEC 62343-3-1:2016 © IEC 2016

DYNAMIC MODULES –

Part 3-1: Performance specification templates –
Dynamic channel equalizers

1 Scope

This part of IEC 62343 provides a performance specification template for the dynamic channel
equalizer (DCE). The object of this performance specification template is to provide a
framework for the preparation of detail specifications on the product or performance of
dynamic channel equalizers.

Additional specification parameters may be included for product specifications or performance
specifications. However, specification parameters specified in this standard should not be
removed from the product specifications or performance specifications.

Technical information regarding dynamic channel equalizers and their applications in DWDM
systems is described in IEC TR 62343-6-1.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.

IEC 61300-2-14, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 2-14: Tests – High optical power

IEC 61300-3-2, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-2: Examinations and measurements – Polarization
dependent loss in a single-mode fibre optic device

IEC 61300-3-6, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-6: Examinations and measurements – Return loss

IEC 61300-3-29, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-29: Examinations and measurements – Spectral
transfer characteristics of DWDM devices

IEC 61300-3-32, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-32: Examinations and measurements – Polarization
mode dispersion measurement for passive optical components

IEC 61300-3-38, Fibre optic interconnecting devices and passive components – Basic test
and measurement procedures – Part 3-38: Examinations and measurements – Group delay,
chromatic dispersion and phase ripple

IEC 61753-021-2, Fibre optic interconnecting devices and passive components performance
standard – Part 021-2: Grade C/3 single-mode fibre optic connectors for category C –
Controlled environment

IEC 62343, Dynamic modules – General and guidance

BS EN 62343-3-1:2016 – 7 –
IEC 62343-3-1:2016 © IEC 2016

ITU-T Recommendation G.694.1, Spectral grids for WDM applications: DWDM frequency grid

3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 62343 apply.

4 Test report

Fully documented test reports and supporting evidence shall be prepared and be available for
inspections as evidence that the tests have been carried out and complied with.

5 Reference components
The testing for DCE components does not require the use of reference components.

6 Performance requirements

6.1 Dimensions
Dimensions shall comply with either an appropriate IEC interface standard, or with those
given in the manufacturer's drawings, where the IEC interface standard does not exist or
cannot be used.

6.2 Sample size

The test sample size and sequencing requirements for the module components shall be
defined in the relevant specification.

6.3 Test details and requirements
The requirements are given only for non-connectorized DCE devices. For connectorized
components, the connector performances shall be in compliance with IEC 61753-021-2.

A minimum length of fibre or cable of 1,5 m per port shall be included in all climatic and
environmental tests.

The channel spacings, unless otherwise specified, shall be in accordance with
ITU­T Recommendation G.694.1. Environmental tests shall be measured for a single
input/output port combination.

The test details and requirements are given in Table 1.

– 8 – BS EN 62343-3-1:2016
IEC 62343-3-1:2016 © IEC 2016

Table 1 – Tests and requirements

No. Test parameters Unit Details
1 Insertion loss
dB IEC 61300-3-29
2
3 Over the operating Source: The source shall be tuneable over the
4 wavelength range operating wavelength range and shall have a
spectral width of ≤ 1 GHz
5 In band extinction ratio dB
dB The source stability shall be ≤ 0,25 GHz

6 Out of band attenuation dB
Class W The source output shall be unpolarized
7 Return loss
8 (branching device method) Detector: The linearity of the detector shall be
9 within ± 0,05 dB
10 Polarization dependent dB
11 The spectral response shall be matched to the
12 loss source
13
Polarization mode ps The dynamic range shall be consistent with the
attenuation values to be measured
dispersion
The maximum attenuation value specified
Output channel non- dB applies to any combination of input/output ports
uniformity
dB Method under consideration
Input channel non-
uniformity dB Method under consideration
GHz
Ripple s IEC 61300-3-6
GHz
Channel frequency range ps/nm Branching device: The nominal splitting ratio
shall be 50/50
Channel response time
The directivity shall be ≥60 d B
Channel spacing
Source: The central wavelength shall be
Chromatic dispersion 1 550 nm ± 20 nm

The power stability of the light source shall be

better than ± 0,05 dB over the measuring
period

Detector: The linearity of the detector shall be
within ± 0,05 dB

The detector sensitivity shall be
< -80 dBm

All ports not under test shall be terminated to
avoid unwanted back reflections contributing to
the measurement

IEC 61300-3-2, Method 1

Other details shall be the same as in test no. 1

The polarization dependant loss shall be
measured between any input/output port
combination

IEC 61300-3-32

Other details shall be the same as in test no. 1

The polarization mode dispersion shall be
measured between any input/output port
combination

IEC 61300-3-29

IEC 61300-3-29

IEC 61300-3-29

Method under consideration

Method under consideration

Method under consideration

IEC 61300-3-38

BS EN 62343-3-1:2016 – 9 –
IEC 62343-3-1:2016 © IEC 2016
Unit
No. Test parameters Details
14 Channel crosstalk
15 dB IEC 61300-3-29
Adjacent channel dB IEC 61300-3-29
16 attenuation crosstalk
dBm IEC 61300-2-14
Maximum input power

– 10 – BS EN 62343-3-1:2016
IEC 62343-3-1:2016 © IEC 2016

Bibliography

IEC 61300 (all parts), Fibre optic interconnecting devices and passive components – Basic

test and measurement procedures

IEC 61753-1, Fibre optic interconnecting devices and passive components performance
standard – Part 1: General and guidance for performance standards

IEC TR 62343-6-1, Dynamic modules – Part 6-1: Dynamic channel equalizers

ITU-T Recommendation G.671, Transmission characteristics of optical components and
subsystems

_____________

This page deliberately left blank

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

British Standards Institution (BSI)

BSI is the national body responsible for preparing British Standards and other
standards-related publications, information and services.

BSI is incorporated by Royal Charter. British Standards and other standardization
products are published by BSI Standards Limited.

About us Reproducing extracts

We bring together business, industry, government, consumers, innovators For permission to reproduce content from BSI publications contact the BSI
and others to shape their combined experience and expertise into standards Copyright & Licensing team.
-based solutions.
Subscriptions

The knowledge embodied in our standards has been carefully assembled in
a dependable format and refined through our open consultation process. Our range of subscription services are designed to make using standards
Organizations of all sizes and across all sectors choose standards to help easier for you. For further information on our subscription products go to
them achieve their goals. bsigroup.com/subscriptions.
With British Standards Online (BSOL) you’ll have instant access to over 55,000
Information on standards British and adopted European and international standards from your desktop.
It’s available 24/7 and is refreshed daily so you’ll always be up to date.
We can provide you with the knowledge that your organization needs You can keep in touch with standards developments and receive substantial
to succeed. Find out more about British Standards by visiting our website at discounts on the purchase price of standards, both in single copy and subscription
bsigroup.com/standards or contacting our Customer Services team or format, by becoming a BSI Subscribing Member.
Knowledge Centre. PLUS is an updating service exclusive to BSI Subscribing Members. You will
automatically receive the latest hard copy of your standards when they’re
Buying standards revised or replaced.
To find out more about becoming a BSI Subscribing Member and the benefits
You can buy and download PDF versions of BSI publications, including British of membership, please visit bsigroup.com/shop.
and adopted European and international standards, through our website at With a Multi-User Network Licence (MUNL) you are able to host standards
bsigroup.com/shop, where hard copies can also be purchased. publications on your intranet. Licences can cover as few or as many users as you
wish. With updates supplied as soon as they’re available, you can be sure your
If you need international and foreign standards from other Standards Development documentation is current. For further information, email
Organizations, hard copies can be ordered from our Customer Services team.
Revisions
Copyright in BSI publications
Our British Standards and other publications are updated by amendment or revision.
All the content in BSI publications, including British Standards, is the property We continually improve the quality of our products and services to benefit your
of and copyrighted by BSI or some person or entity that owns copyright in the business. If you find an inaccuracy or ambiguity within a British Standard or other
information used (such as the international standardization bodies) and has BSI publication please inform the Knowledge Centre.
formally licensed such information to BSI for commercial publication and use.
Useful Contacts
Save for the provisions below, you may not transfer, share or disseminate any
portion of the standard to any other person. You may not adapt, distribute, Customer Services

commercially exploit, or publicly display the standard or any portion thereof in any Tel: +44 345 086 9001
manner whatsoever without BSI’s prior written consent. Email (orders):
Email (enquiries):
Storing and using standards
Subscriptions
Standards purchased in soft copy format: Tel: +44 345 086 9001
Email:
• A British Standard purchased in soft copy format is licensed to a sole named
user for personal or internal company use only. Knowledge Centre
Tel: +44 20 8996 7004
• The standard may be stored on more than 1 device provided that it is accessible Email:
by the sole named user only and that only 1 copy is accessed at any one time.
Copyright & Licensing
• A single paper copy may be printed for personal or internal company use only. Tel: +44 20 8996 7070
Email:
Standards purchased in hard copy format:
BSI Group Headquarters
• A British Standard purchased in hard copy format is for personal or internal
company use only. 389 Chiswick High Road London W4 4AL UK

• It may not be further reproduced – in any format – to create an additional copy.
This includes scanning of the document.

If you need more than 1 copy of the document, or if you wish to share the
document on an internal network, you can save money by choosing a subscription
product (see ‘Subscriptions’).