CCNA Wireless Official Exam Certification Guide part 6 ppt

22 CCNA Wireless Official Exam Certification Guide
2. True or false: The U.S. complies with ETSI standards of EIRP.
a. True
b. False
3. What is the maximum EIRP for point-to-multipoint in Europe? (Choose all that apply.)
a. 20 dBm
b. 17 dBi
c. 17 dBm
d. 36 dBm
4. The FCC regulates EIRP in the U.S. to a maximum of _____ for point-to-point and
_____ for point-to-multipoint.
a. 36 dBm, 36 dBm
b. 30 dBm, 17 dBm
c. 17 dBm, 36, dBm
d. 36 dBm, 17 dBm
5. The IEEE committees work on which of the following wireless standards? (Choose all
that apply.)
a. 802.11a
b. 802.11g
c. 802.11x
d. 802.1q
e. 802.11b
6. True or false: The IEEE is a regulatory body in the U.S. that controls the usage of
wireless frequencies.
a. True
b. False
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 22
Chapter 2: Standards Bodies 23
7. In Europe, can a professional installer increase the gain on wireless antennas?
a. Yes, provided that he or she decreases the transmit power using a 1:1 ratio.
b. No; this is illegal.

c. Only with a wavier.
d. Antennas don’t have anything to do with gain.
8. The FCC regulates that professional installers maintain what ratio of gain to transmit
power when increasing the gain of an antenna?
a. 3:1
b. 1:1
c. 6:1
d. 1:3
9. Which organization certifies interoperability for wireless equipment?
a. Wi-Max Alliance
b. IEEE
c. Wi-Fi Alliance
d. FRF.12
10. Certification of wireless equipment includes which protocols and standards for inter-
operability? (Choose two.)
a. 802.11a/b/g
b. IPsec
c. WPA/WPA2
d. Zigbee
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 23
24 CCNA Wireless Official Exam Certification Guide
Foundation Topics
Wireless Standards and Regulatory Committees
Many people benefit from the availability of wireless Internet access as they travel to vari-
ous parts of the world. Without regulatory committees and organizations to ensure the
proper use and interoperability of equipment, it’s likely that people could not connect
from place to place. To ensure that certain rules governing the use of wireless RF are ad-
hered to, numerous country-specific organizations and global committees monitor stan-
dards and usage. This chapter discusses some of them.
FCC

The Federal Communications Commission (FCC) is an independent agency in the United
States that regulates communication methods. It is held directly responsible by Congress.
It is the FCC in the United States that governs the frequency ranges that can be used with-
out a license, the transmit power of devices, the types of devices that can be used indoors
as well as outdoors, and how the various types of hardware can be used. The FCC exists
because of the Communications Act of 1934.
Note: The FCC website is .
When it comes to the FCC and Cisco wireless, it’s important to know the requirements de-
fined in FCC - Part 15 - Antenna Requirements. This federal requirement states that an-
tennas must use a unique nonstandard connector that cannot be acquired easily. The
reason for not being acquired easily is to ensure that home users and noncertified in-
stallers cannot easily deploy an antenna that goes beyond the regulated values. For this
reason, Cisco uses a connector known as the Reverse-Polarity-Threaded Neil-Concelman
(RP-TNC) connector, as shown in Figure 2-1.
What makes this connector unique is that the center contacts are reversed so that you
can’t use a store-bought antenna with a Cisco wireless device. If you did so, you might vi-
olate the FCC regulatory requirements.
Figure 2-1 RP-TNC Connector
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 24
Chapter 2: Standards Bodies 25
In addition to the antenna rules, the FCC defines power output rules that must be fol-
lowed. There are rules for everyday people to follow, and rules for people who are consid-
ered professionals in the field. A professional has a little more leeway than someone who
buys a wireless device at the local electronics store. To get an idea of these rules, you can
look at the 2.4-GHz EIRP Output Rules. Effective Isotropic Radiated Power (EIRP) is a
way to measure the amount of energy radiated from an antenna. EIRP is an important con-
cept to understand, especially when you’re dealing with regulatory bodies. It’s important
that the EIRP not exceed that mandated by the governing bodies. These rules are de-
signed for point-to-point scenarios as well as point-to-multipoint. The point-to-point rules
are as follows:

■ You can have a maximum of 36-dBm EIRP.
■ You can have a maximum of 30-dBm transmitter power with 6-dBi gain of antenna
and cable combined.
■ You are allowed a 1:1 ratio of power to gain.
For point-to-multipoint scenarios, you are allowed the same maximum EIRP and the same
maximum transmitter power and antenna gain; however, you can exceed the 36-dBm EIRP
rule using a 3:1 ratio of power to gain.
Table 2-2 compares the FCC maximum requirements for point-to-point to the Cisco
maximum.
Table 2-3 compares the FCC maximum requirements for point-to-multipoint to the Cisco
maximum.
ETSI
The European Telecommunication Standards Institute (ETSI) is the not-for-profit organiza-
tion that standardizes the frequencies and power levels used in Europe as well as many
Table 2-2 FCC Antenna Requirements Versus Cisco Standards for Point-to-Point
Environments
Transmitter Power Maximum Gain EIRP
FCC Maximum 30-dBm 6-dBm 36-dBm
Cisco Maximum 20-dBm 36-dBm 56-dBm
Table 2-3 FCC Antenna Requirements Versus Cisco Standards for Point-to-Multipoint
Environments
Transmitter Power
Maximum Gain EIRP
FCC Maximum 30-dBm 6-dBm 36-dBm
Cisco Maximum 20-dBm 36-dBm 36-dBm
Key
Topi
c
Key
Topi

c
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 25
26 CCNA Wireless Official Exam Certification Guide
other countries. The European Commission (EC) recognizes ETSI as an official European
Standards Organization. Many of the mandates for wireless usage come from the EC.
Then, ETSI defines various standards based on these mandates. According to the ETSI
website, the ETSI has almost 700 members in 60 countries.
Similar to the FCC, the ETSI has 2.4-GHz EIRP output rate standards that you should be
familiar with. The ETSI’s rules, however, are different from the FCC’s rules. ETSI defines
20-dBm EIRP on point-to-multipoint and on point-to-point with 17-dBm maximum trans-
mit power with 3-dBi gain. In a way, this is easier to remember, because these numbers are
the same value for both point-to-point and point-to-multipoint connections. Of course, a
professional installer can increase the gain as long as he or she lowers the transmit power
below 17 dBm at a ratio of 1:1. Therefore, a professional installer could drop the transmit
power by 1 dBm and increase the gain by 1 dBm and still stay within the guidelines.
Table 2-4 compares the Cisco standards to the ETSI standards for EIRP. The table shows
the governing body maximum transmitted power, maximum gain, and EIRP compared to
that of the Cisco integated antennas. You can see that the Cisco antenna has a transmit
power of 17 dBm and a maximum gain of 2.2 dBi and ends up with an EIRP of 19.2 dBm,
which is lower than the 20 dBm allowed by the governing bodies. If you reduced the
transmit power to 15 dBm and increased the maximum gain to 5 dBi, the resulting EIRP
would be 20 dBm, which is still within the guidelines of the governing body. Likewise, re-
ducing the transmit power to 13 dBm and increasing the gain to 7 dBi keeps the EIRP at
20 dBm—within the guidelines.
Table 2-4 Cisco Versus ETSI EIRP Standards for Point-to-Point and Point-to-Multipoint
Environments
Transmitter
Power (dBm)
Maximum
Gain (dBi)

EIRP (dBm)
Governing Body Maximum 17 3 20
Cisco Integrated Antennas 17 2.2 19.2
Reduced Tx Power 15 5 20
Reduced Tx Power 13 7 20
Reduced Tx Power 7 13 20
Reduced Tx Power 0 20 20
Key
Topi
c
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 26
Chapter 2: Standards Bodies 27
IEEE
The Institute of Electrical and Electronics Engineers (IEEE) is a not-for-profit organization
that has more than 370,000 members globally. It has 319 sections in ten geographic areas.
It has defined more than 900 standards and has another 400 in development.
Note: For a history of the IEEE, see />The IEEE’s “Wireless Standards Zone” is dedicated to standards that are related to wireless
technology. Here you can find information about the 802 protocols, such as the following:
■ 802.11: The Working Group for Wireless LAN
■ 802.15: The Working Group for Wireless PAN
■ 802.16: The Working Group for Broadband Wireless Access Standards
Note: You can find the Wireless Standards Zone at and
an overview of the aforementioned working groups at />overview.html.
This book focuses mainly on the 802.11a, 802.11b, 802.11g, and 802.11n protocols. These
protocols are for wireless LANs.
Wi-Fi Certification
Into the arena of interoperability testing enters the Wi-Fi Alliance. The Wi-Fi Alliance is a
not-for-profit organization that certifies the interoperability of more than 4200 products.
The Wi-Fi Alliance was formed in 1999 and currently has more than 300 members in more
than 20 countries. What makes this organization different from the ETSI, FCC, and IEEE

is that it gives its seal of approval to devices that plan in interoperability. The next time
you’re at the electronics shop, flip over one of the wireless products; you might find it to
be Wi-Fi Certified. If so, you will notice that the 802.11a, 802.11b, and 802.11g protocols
are certified if the device can use them as well as security protocols such as WPA and
WPA2. Usually, the label has a checkmark next to what the device is certified for.
Note: The Wi-Fi alliance can be found at .
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 27
28 CCNA Wireless Official Exam Certification Guide
Table 2-5 Key Topics for Chapter 2
Key Topic Item Description Page Number
Table 2-2 FCC antenna requirements versus Cisco stan-
dards (point-to-point)
25
Table 2-3 FCC antenna requirements versus Cisco stan-
dards (point-to-multipoint)
25
Table 2-4 Cisco versus ETSI EIRP standards (point-to-
point and point-to-multipoint)
26
Exam Preparation Tasks
Review All the Key Topics
Review the most important topics from this chapter, denoted with the Key Topic icon.
Table 2-5 lists these key topics and the page number where you can find each one.
Complete the Tables and Lists from Memory
Print a copy of Appendix B, “Memory Tables,” (found on the CD) or at least the section
for this chapter, and complete the tables and lists from memory. Appendix C, “Memory Ta-
bles Answer Key,” also on the CD, includes completed tables and lists to check your work.
Definition of Key Terms
Define the following key terms from this chapter, and check your answers in the glossary:
FCC, IEEE, ETSI, W-Fi Alliance, EIRP

03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 28
03_1587202115_ch02.qxd 9/29/08 2:46 PM Page 29
This chapter covers the following subjects:
Characteristics of Wireless Networks:
Provides a review of wireless transmissions.
Influences on Wireless Transmissions:
Covers the different elements that can affect wireless
transmissions.
Determining Signal Strength Influences:
Describes how to determine your signal strength and
what might be influencing your wireless deployment.
04_1587202115_ch03.qxd 9/29/08 2:42 PM Page 30
CHAPTER 3
WLAN RF Principles
Table 3-1 “Do I Know This Already?” Section-to-Question Mapping
Foundation Topics Section Questions
Characteristics of Wireless Networks 1–3
Influences on Wireless Transmissions 4–9
Determining Signal Strength Influences 10–11
In wireless technologies, you need to understand what influences act on wireless transmis-
sions. This chapter reviews the characteristics of wireless transmissions and the influences
that act on them, sometimes causing problems. Some of the material covered in the first
section, “Characteristics of Wireless Networks,” is a review of information you learned in
Chapter 1, “Introduction to Wireless Networking Concepts.” If you are comfortable with
your knowledge of this information, you can just review the key topics at the end of this
chapter.
The second section of this chapter covers influences on wireless transmissions. These are
usually drawbacks, so you should become familiar with them. The third part of this chap-
ter discusses ways to determine signal strength and other influences on wireless signals.
You should do the “Do I Know This Already?” quiz first. If you score 80% or higher, you

might want to skip to the section “Exam Preparation Tasks.” If you score below 80%, you
should spend the time reviewing the entire chapter. Refer to Appendix A, “Answers to the
‘Do I Know This Already?’ Quizzes” to confirm your answers.
“Do I Know This Already?” Quiz
The “Do I Know This Already?” quiz helps you determine your level of knowledge of this
chapter’s topics before you begin. Table 3-1 details the major topics discussed in this chap-
ter and their corresponding quiz questions.
04_1587202115_ch03.qxd 9/29/08 2:42 PM Page 31