Volume 06 - Welding, Brazing and Soldering Part 10 pps

TABLE 3 COMPOSITION OF SELECTED MECHANICALLY ALLOYED MATERIALS

ALLOY
Fe Cr Al Ti Ni C Y
2
O
3


. . .
. . .
0.3
MA 6000

. . . 15.0

4.5

2.5

BAL

0.5 0.6 . . .
TABLE 4 PROPERTIES OF SELECTED MECHANICALLY ALLOYED MATERIALS

DENSITY YOUNG'S
MODULUS
TENSILE
STRENGTH
(A)

YIELD
STRENGTH
(A)
100 H

ALLOY
G/CM
3
LB/IN.
3
GPA 10
6
PSI MPA KSI MPA KSI
ELONGATION

AT
FRACTURE,
%
(A)
MPA KSI MPA

13.6

7.4
. . .
MA
6000
(B)

8.11 0.293 203 29.4 222 32.2 192 27.8 9 131 19 127 18.5

REPAIR OF TURBINE BLADES AND VANES,
WELD. J.,
HYDROCARBON PROCESS.,
WELD. J.,
CAN. WELD. FABRICAT.,
PROCEEDINGS: SEMINAR ON DISSIMILAR WELDS IN FOSSIL-FIRED BOILERS,
WELD. J.,
CAN. WELD. FABRICAT.,
WELDING IAI-14,
REPAIR OF TURBINE BLADES AND VANES,
WELD. J.,
HYDROCARBON PROCESS.,
WELD. J.,
CAN. WELD. FABRICAT.,
PROCEEDINGS: SEMINAR ON DISSIMILAR WELDS IN FOSSIL-FIRED BOILERS,
WELD. J.,
CAN. WELD. FABRICAT.,
t
t
J. MET.,
WELD. J.,
WELD.
J.,
INT. J. REFRACT. HARD MET.,
METALL. TRANS. B,
MET.
TECHNOL.,
WELD. LNT.,

MATER. SCI. ENG.,
WELD. J.,
TUNGSTEN,
J. MET.,
WELD. J.,
WELD. J.,
INT. J. REFRACT. HARD MET.,
METALL. TRANS. B,
MET.
TECHNOL.,
WELD. LNT.,
MATER. SCI. ENG.,
WELD. J.,
TUNGSTEN,
WELD. J.,
REFRACTORY METALS AND THEIR INDUSTRIAL APPLICATIONS,
RHENIUM ALLOYS,
INT. MATER. REV.,
Corrosion, ASM
Handbook,
J.
MET.,
•
•
•
•
•

J.
MET.,
TABLE 1 COMPOSITIONS OF SELECTED NICKEL-BASE CORROSION-RESISTANT ALLOYS
COMPOSITION, WT% ALLOY
Ni Cr Fe Cu C0 Si Al Ti Mo
NICKEL ALLOYS
NICKEL-COPPER ALLOY
NICKEL-CHROMIUM ALLOYS
NICKEL-CHROMIUM-IRON ALLOYS
TABLE 2 PROPERTIES OF SELECTED NICKEL-BASE CORROSION-RESISTANT ALLOYS
MELTING
RANGE
THERMAL
CONDUCTIVITY
ALLOY DENSITY,

G/CM
3

°C °F
COEFFICIENT OF

THERMAL
EXPANSION
(A)
,
10
-6
/K
W/M

2
·K BTU/FT
2
·
H · °F
ELECTRICAL

RESISTIVITY,

10
-8
Ω/M
•
•
•

WELD. J.,
WELD. J.,
WELDING RESEARCH COU
NCIL
SYMPOSIUM ON EFFECTS OF MINOR ELEMENTS ON THE WELDABILITY OF HIGH-
NICKEL
ALLOYS,
PROC.
FIFTH BOLTON LANDING CONF.,
TABLE 3 TYPICAL ANNEALING TEMPERATURES FOR CORROSION-RESISTANT NICKEL, NICKEL-
COPPER, NICKEL-CHROMIUM, AND NICKEL-CHROMIUM-IRON ALLOYS

TEMPERATURE
(A)
ALLOY UNS NO.
°C °F
TABLE 4 RECOMMENDED HEAT TREATMENT PROCEDURES FOR SELECTED NICKEL-
BASE
CORROSION-RESISTANT ALLOYS
ALLOYS 200 AND 201 FOR CAUSTIC SERVICE
ALLOY 600 FOR CAUSTIC SERVICE
ALLOY 400 FOR HYDROFLUORIC ACID SERVICE