Các lệnh trong PDMS

No. COMMAND EXTEND FUNCTION EXPLAINATION WORKING
1 REM ALL Remove all CE from drawlist
EQUIP-STRU-
PIPE
2 REM CE Remove CE from drawlist
EQUIP-STRU-
PIPE
3 REM ALL EQUI Remove all CE of EQUI from drawlist EQUIP
4 REM ALL STRU Remove all CE of STRU from drawlist STRU
5 REM ALL PIP Remove all CE of Pipe from drawlist PIPE
6 MOVE U THROU ID@ / IDP@ / PRE Move Object follow U direction to Pick Element EQUIP-STRU
7 MOVE D THROU ID@ / IDP@ / PRE Move Object follow D direction to Pick Element EQUIP-STRU
8 MOVE E THROU ID@ / IDP@ / PRE Move Object follow E direction to Pick Element EQUIP-STRU
9 MOVE W THROU ID@ / IDP@ / PRE Move Object follow W direction to Pick Element EQUIP-STRU
10 MOVE N THROU ID@ / IDP@ / PRE Move Object follow N direction to Pick Element EQUIP-STRU
11 MOVE S THROU ID@ / IDP@ / PRE Move Object follow S direction to Pick Element EQUIP-STRU
12 MOVE U CLEA BEH ID@ / IDP@ / PRE Move Object follow U direction to Clean Behind of Pick Element EQUIP-STRU
13 MOVE D CLEA BEH ID@ / IDP@ / PRE Move Object follow D direction to Clean Behind of Pick Element EQUIP-STRU
14 MOVE E CLEA BEH ID@ / IDP@ / PRE Move Object follow E direction to Clean Behind of Pick Element EQUIP-STRU
15 MOVE W CLEA BEH ID@ / IDP@ / PRE Move Object follow W direction to Clean Behind of Pick Element EQUIP-STRU
16 MOVE N CLEA BEH ID@ / IDP@ / PRE Move Object follow N direction to Clean Behind of Pick Element EQUIP-STRU
17 MOVE S CLEA BEH ID@ / IDP@ / PRE Move Object follow S direction to Clean Behind of Pick Element EQUIP-STRU
18 MOVE U CLEA INFR ID@ / IDP@ / PRE Move Object follow U direction to Clean Infront of Pick Element EQUIP-STRU
19 MOVE D CLEA INFR ID@ / IDP@ / PRE Move Object follow D direction to Clean Infront of Pick Element EQUIP-STRU
20 MOVE E CLEA INFR ID@ / IDP@ / PRE Move Object follow E direction to Clean Infront of Pick Element EQUIP-STRU
21 MOVE W CLEA INFR ID@ / IDP@ / PRE Move Object follow W direction to Clean Infront of Pick Element EQUIP-STRU
22 MOVE N CLEA INFR ID@ / IDP@ / PRE Move Object follow N direction to Clean Infront of Pick Element EQUIP-STRU
23 MOVE S CLEA INFR ID@ / IDP@ / PRE Move Object follow S direction to Clean Infront of Pick Element EQUIP-STRU
24
MOVE E WRT SITE DIST 100 /*
Move a primitive in the proper direction irregardless of its owners’ orientation

EQUIP-STRU-
PIPE
25 BY U 500 /D/E/W/N/S Move object follow U direction Dist 500mm
EQUIP-STRU-
PIPE
26 ROTATE BY 45 ABOUT Z /X /Y Rota element 45 degree about Z axis
EQUIP-STRU-
PIPE
27 ROTATE BY 45 ABOUT Z THRO ID@ /X /Y Rota element 45 degree about Z axis with center Pick element
EQUIP-STRU-
PIPE
28
NAME /NEWNAME
Rename the CE
EQUIP-STRU-
PIPE
29
PREC 2 DP
Set precision, To alter the precision ( to 2 decimal places) EQUIP
30 Q DTXR To See Desc Of Component PIPE
31
Q STYP
To See STYPE Of Component PIPE
32
Q MTXX
To See MATERIAL/VENDOR INFO PIPE
33 Q STEXT To see Name of Attachment PIPE
34 STEXT ‘NOTE’ Naming For Attachment PIPE
35 Q ISPEC To see the insulation of pipe PIPE
36 ISPEC NULREF To Remove the Insulation of Pipe PIPE

37
Q INSU
Gives you the insulation thickness PIPE
38
Q SEQ
Gives you the sequence of the CE in the hierarchy PIPE
39 Q SPREF Check Name of component/data information PIPE
40 Q P1 P2 P3 To see pipe Bore Direction Connection type and Position PIPE
41 Q ANGLE To see Angle of Elbow PIPE
42 Q TREF HREF To see Head and Tail branch connection PIPE
43 Q PL DIR PA / P1/P2/P3 To see Leave ( Arrive ) Point direction of Elbow or Tee PIPE
44 Q PL PA/P1/P2/P3 To see Leave ( Arrive ) Point direction of Elbow or Tee and Pos PIPE
45 Q PL BOP POS PA To see position Bottom of pipe PIPE
46 Q PL TOP POS PA To see position Top of pipe PIPE
47
Q PL BOP WRT SITE
PA
Allows you to query the bottom of pipe Leave elevation with respect to the
site PIPE
48
Q PL BOP WRT WORLD
PA
Allows you to query the bottom of pipe Leave elevation with respect to the
world PIPE
49 Q LTLE To cheek pipe length PIPE
50 Q LSTUBE To see and Change the spec Brake PIPE
51 Q PSPEC To see the pipe spec PIPE
52 CH CE check current element (check consistencies )
EQUIP-STRU-
PIPE

53 CONN NEXT Connection to next element PIPE
54 FCONN For force connection PIPE
55 DIST 500 DIST from relative ori to CE PIPE
56 DIST 500 FROM PRE DIST from previous component PIPE
57 AXES AT PH To see Axes of Pipe Head PIPE
58 AXES AT PT To see Axes of Pipe Tail PIPE
59 AXES AT POSE S To see Axes of End of section STRU
60 AXES OFF To OFF Axes STRU-PIPE
61 DIR D
/ E / W / N / S /
U Direction for Elbow PIPE
62 THRO NEXT (To connect element to next component) Move element to center of next component PIPE
63 BRA CONN PH TO FIRST MEM Connec branch head to first member PIPE
64 BRA CONN PT TO LAST MEM Connec branch tail to last member PIPE
65 BRA CONN PH TO NOZZ ID@ /PT Connec branch Head to Nozz PIPE
66 BRA CONN PH TO TEE ID@ /PT Connect Branch Head to Tee PIPE
67 BRA CONN PH TO PT OF ID@ Connect Branch Head to Branch Tail of other pipe PIPE
68 CONN NEXT Connection to next element PIPE
69 FORWARDS - DIR TOW NEXT - BACK - DIR TOW NEXT For Slope line / Rotated Elbow PIPE
70 REPR INSU ON/OFF UPDATE To ON/OFF insulation of Pipe PIPE
71
ORI AND P3 IS W
Rotate a pipe tee or valve PIPE
72 Q ATT To see the attributes
EQUIP-STRU-
PIPE
73 Q PARA To check nozzle size EQUIP-PIPE
74 Q CATREF To See nozzle Rating EQUIP
75 Q U To see relative U Position of CE EQUIP-STRU
76 Q U WRT/* / WW To see Absolute U Position of CE EQUIP-STRU

77 Q POS To see relative Position of CE
EQUIP-STRU-
PIPE
78 Q P1 POS To see relative Position of P1
EQUIP-STRU-
PIPE
79 Q P2 POS To see relative Position of P2
EQUIP-STRU-
PIPE
80 Q POS ID@ IDP@ To see relative Position of CE or Point
EQUIP-STRU-
PIPE
81 Q U POS ID@ IDP@ To see relative U of Position of CE or Point
EQUIP-STRU-
PIPE
82 Q E POS ID@ IDP@ To see relative E of Position of CE or Point
EQUIP-STRU-
PIPE
83 Q POS IN WORLD To see absolute Position of CE
EQUIP-STRU-
PIPE
84 Q POS WRT/* To see absolute Position of CE
EQUIP-STRU-
PIPE
85 Q POS ID@ WRT/* IDP@ To see absolute Position of CE or Point
EQUIP-STRU-
PIPE
86 Q POS WW To see absolute Position of CE
EQUIP-STRU-
PIPE

87 Q POS ID@ WW IDP@ To see absolute Position of CE or Point
EQUIP-STRU-
PIPE
88 Q P1 POS WW To see absolute Position of P1
EQUIP-STRU-
PIPE
89 Q P2 POS WW To see absolute Position of P2
EQUIP-STRU-
PIPE
90 Q POSE WRT/* S To see Position of End/Start section STRU
91 Q ORI To see the Relative Orientation
EQUIP-STRU-
PIPE
92 Q ORI WRT/*
/ WW / IN
WORLD To see the Absolute Orientation
EQUIP-STRU-
PIPE
93
Q DBNAME
DATABASE NAME
EQUIP-STRU-
PIPE
94 Q MEM To see all member in Object
EQUIP-STRU-
PIPE
95 Q NAME To see name of CE
EQUIP-STRU-
PIPE
96 ALP REQ CLEAR CLEAN ALL COMMAND LINE

EQUIP-STRU-
PIPE
97
FINISH
Saves PDMS session and exits the application.
EQUIP-STRU-
PIPE
98 QUIT FINISH Exits the application Not SAVE
EQUIP-STRU-
PIPE
99
EXIT
Exits you to MONITOR with a SAVE
EQUIP-STRU-
PIPE
100
QUIT
Exits you to MONITOR without saving whatever
EQUIP-STRU-
PIPE
101
SAVEWORK
Save the current model
EQUIP-STRU-
PIPE
102
GETWORK
Open the latest model
EQUIP-STRU-
PIPE

103
REFRESH
Refresh the screen
EQUIP-STRU-
PIPE
104
ADD CE
Add member to drawliest
EQUIP-STRU-
PIPE
105
ADD CREF
Add Pipe Member Which is connect with Nozzle to drawlist EQUIP
106
ADD CREF HREF
Add branch or nozzle which is connect with branch current PIPE
107
ADD ALL WITHIN VOL CE

Add all disciplines that overlap CE
EQUIP-STRU-
PIPE
108
ADD ALL WITHIN VOL CE 100

Add all disciplines that overlap CE with a volume of 100mm all
round
EQUIP-STRU-
PIPE
109

ADD ALL SCTN WITHIN VOL CE Add all Sections that overlap CE
EQUIP-STRU-
PIPE
110
ADD ALL EQUIP WITHIN VOL CE Add all Equipment that overlaps CE
EQUIP-STRU-
PIPE
111
UNCLAIM ALL
Unlock all Claimed members
EQUIP-STRU-
PIPE
112
LOCK ALL
Lock the CE and CE Members:
EQUIP-STRU-
PIPE
113 UNLOCK ALL UNLock the CE and CE Members:
EQUIP-STRU-
PIPE
114 BACK Backward
EQUIP-STRU-
PIPE
115 FORW Forward
EQUIP-STRU-
PIPE
116 Q MODE Displays whether in forward or backward mode
EQUIP-STRU-
PIPE
117 NEXT Move to next element

EQUIP-STRU-
PIPE
118 PRE Move to pre element
EQUIP-STRU-
PIPE
119
AT @
Move CE to a new cursor position
EQUIP-STRU-
PIPE
120 AT IDP@
Move CE to a selected P-Point
EQUIP-STRU-
PIPE
121
AT IDPL@ Move CE to a Selected P-Line
EQUIP-STRU-
PIPE
122
POS IDP@ AT IDP@ Move CE from Point to Point
EQUIP-PIPE
123
AUTO CE
Zoom in on the Current Element
EQUIP-STRU-
PIPE
124
COL CE VIOLET
Change the CE colour to Violet:
EQUIP-STRU-

PIPE
125
COL ACT BLUE
Change the Active colour to Blue:
EQUIP-STRU-
PIPE
126
CONST DIST IDP@ TO IDP@
Measure DIST from point to point EQUIP
127
CONST DIST P0 TO P0 OF ID@
Measure DIST from P0 of current ce to P0 of another point EQUIP
128
CONST DIST PA TO PA OF NEX
Measure DIST from PA to next PA of current component PIPE
129 MARK CE MEMBER To Mark all name of member in object
EQUIP-STRU-
PIPE
130
MARK CE
Add a tag to the element on the 3D View.
EQUIP-STRU-
PIPE
131
MAR CE
Add a tag to the element on the 3D View.
EQUIP-STRU-
PIPE
132
MARK WITH 'Hello World' ID @

Add a tag "Hello World" to Pick element
EQUIP-STRU-
PIPE
133
MARK WITH 'Hello World' CE
Add a tag "Hello World" to Current element
EQUIP-STRU-
PIPE
134
MARK ALL BRAN
Add tag Name for all Branch
EQUIP-STRU-
PIPE
135
MARK ALL VALVE
Add tag Name for all Valve
EQUIP-STRU-
PIPE
136
UNMARK CE
Remove tag at Current element
EQUIP-STRU-
PIPE
137
UNMARK ID @
Remove tag at Pick element
EQUIP-STRU-
PIPE
138
UNMARK ALL

Remove all tag
EQUIP-STRU-
PIPE
139
UNM ALL
Remove all tag
EQUIP-STRU-
PIPE
140
NEW EQUI COPY PREV BY N200
Copy new EQUIP and MOVE North 200 mm EQUIP
141
NEW BRAN COPY PREV BY N200
Copy new branch and MOVE North 200 mm PIPE
142
NEW STCN COPY PREV BY E200
Copy new Section and MOVE East 200 mm STRU
143
NEW BOX COPY PREV BY E200
Copy new branch and MOVE East 200 mm EQUIP
144 EXTE END BY E 500 WRT/* /W/N/S/U/D Extend 500 mm from End of section follow E direction (world dir) STRU
145 EXTE START BY E 500 WRT/* /W/N/S/U/D Extend 500 mm from Start of section follow E direction (World dir) STRU
146 EXTE END THRO ID@ START Extend END/START of section to Pick Element. STRU
147 EXTE END THRO IDPL@ (PL-Pline) START Extend END/START of section to PL-PLINE of Pick Element STRU
148 CUTL To see length of section STRU
149 Q DRNS DRNE To see cutting Angle of start and end section STRU
150 DRNSTART S 45 E (Direction and angle) Set cutting angle for Start point of section STRU
151
DRNEND S 45 W (Direction and
angle) Set cutting angle for End point of section STRU

152 REPR HOLES ON UPDATE OFF Display ON/OFF Holes and update EQUIP
153 REPR OBST ON UPDATE OFF Display ON/OFF OBST and update
EQUIP-STRU-
PIPE
154
FLIP CE
Flip the CE STRU-PIPE