cac ky hieu su dung trong may cnc

B1.1 Function description
The setting display of the CRT please refer to manual supplied from the controller
builder.
CRT/MDI control panel：
The controller panel including CRT and function key and power control push
buttons。
※ FANUC-0i-TC
Power ON/OFF

CRT10.4" display

Function key


B1.2 Element functions of machine operator panel

Power switch：POWER ON

Power switch：POWER OFF

Cycle start push – button.

Feed hold:
during the auto program running, the machine will stop cutting
when
the feed hold push button is pressed if the accident happened.
And the
program can be resumed by push the cycle start push – button.
EMG. STOP

Emergency stop.

Data write protect switch:
only when the switch is set to〝on〞the program could be edited,
inserted or deleted.

Auto mode:
when the mode selection switch is set to〝auto〞mode，the CRT
would the program, and be executed.

Transmitting and working at the same time:
Read out data through PC or CNC as turn the button to this
position.

M.D.I mode:
manual data input mode, and the parameters and program could
be
dited at this mode.
Handle mode:
At the handle mode, the axis selection switch is fed by turning
the pulse
Handle。axis feed amount per pulse conforms to the setting of
the
handle switch.
JOG mode: Press directional button to do axis-feed .

RAPID mode: Press directional button to move rapidly as.

Zero return.

Single block:
when this switch is pressed, the indicator is lit, and automatic
operation is executed by one block.
When the indicator is off, The program is executed
continuously.
M01 stop:
when the switch is pressed, the indicator is lit, and the machine
will
become feed hold when the block with M01 is executed.
Dry run:
this function is used to check the program when this program Is
executed at first time and it is valid only when the indicator lit.

Block skip:
when the switch is pressed, the indicator is lit, and the block
with the
〝/〞will be ignored.
Spindle JOG: To adjust spindle RPM by manual.

Spindle ccw rotate push button:
spindle counter clockwise rotates, is equal to the M04
command.
Spindle stop push button:
spindle stops rotates, is equal to the M05 command.

Spindle cw rotate push button: Spindle clockwise rotates, is
equal
to the M03 command.

C axis cw rotate push button.

C axis ccw rotate push button.

Press direction key with〝KEEP〞three second to move
continuously.

To move X-axis in〝﹢〞direction.

To move X-axis in〝﹣〞direction.

To move Z-axis in〝﹢〞direction.

To move Z-axis in〝﹣〞direction.

Auto Shut-down

Rest Apparatus: When this light is on , machine automatically
shutdown while M30 code read in.

Spindle neutral gear indicator.﹙M40﹚


Spindle low gear indicator.﹙M41﹚

Spindle Middle gear indicator.﹙M42﹚

Spindle Middle-high gear indicator.﹙M43﹚

Spindle high gear indicator.﹙M44﹚

Chip conveyor switches: Press and move back.

Chip conveyor switches: Press to go forward continuously.
Press again to stop.

Tool changing push button.

In reserve key.

choose V12 Tools.


choose H4 Tools.

Coolant on/off switch.

Work lamp switch.

Machine lock:
all the axes would not move, but the value of the coordinate will
change
on the screen.
Note: The zero return procedure should be done when turn off
the function.
X axis zero return indicator: When X axis return to the zero
position
, the indicator will get lit.
Z axis zero return indicator: When Z axis return to the zero

position
, the indicator will get lit.
C axis zero return indicator: When C axis return to the zero
position
, the indicator will get lit.
Hydraulic chuck pilot lamp.


Selectivity program stop pilot lamp.

CNC alarm pilot lamp.

Lube alarm pilot lamp.

Coolant alarm pilot lamp.

Machinery alarm pilot lamp.

Hydraulic chuck open.

Hydraulic chuck close.

Program protect.

Program not protect.


Rapid feed rate override:
F0 : 1% of the rapid feed rate.
F25 : 25% of the rapid feed rate.

F50 : 50% of the rapid feed rate.
F100: 100% of the rapid feed rate.

Spindle speed override switch:
The switch is used to override the spindle speed. For instance, if
the spindle speed is 100 rpm in program, and the switch is set to
60%, then the spindle speed will reduce to 60 rpm.

Spindle speed adjustment switch:
this switch at the jog or handle mode could adjust the spindle
speed.
Note: Do not make change the spindle turn to opposite direction
repeatedly, it will damage the gear.
JOG feed ride:
The programmed feed rate is adjuration form 0 to 150% in
increments of 10%.

Mode selection button.

Turret indexing switch.

Load meter: Spindle load meter.


OT

Over travel release:
If X or Z axis over travel, press this button and use handle to
move these axes.
Quá cữ hành trình.

Nếu trục X hoặc trục Z quá cữ, nhấn nút này và sử dụng chế dộ
quay tay tạo xung đễ đưa về.
Fast servomotor turrets to zero: Turn the tool switch to tool
NO.1 and
Choose V12 turret, Then put the tool change button.