HUAWEI EQUIPMENT INSTALLATION
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (361.71 KB, 33 trang )
Guide to Multi-Carrier CDMA2000 BTS3606
Document
Product name
cBTS3606
code
Intended
Maintenance engineer
Product version
V200R001C04B014
audience
Edited by
CBTS
Development
Document version
1.00
Department
Guide to Multi-Carrier CDMA2000
BTS3606
Prepared by:
Dong Qiufeng
Date:
Reviewed by:
Date:
Reviewed by:
Date:
Approved by:
Date:
2005-05-20
Huawei Technologies Co., Ltd.
All rights reversed
2005-08-01
All rights reversed
Page 1 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Revision Record
Date
2005-05-20
Revision version
1.00
Description
The
first
draft
Author
is
Dong Qiufeng
finished.
2005-08-01
All rights reversed
Page 1 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Table of Content
Chapter 1 Overview........................................................................................................................ 2
Chapter 2 Installation..................................................................................................................... 5
2.1 Cable Connection of Typical Configurations..........................................................................5
2.1.1 Configuration of Single Carrier O(1), Multi-Carrier O(2), and Multi-Carrier O(3).......5
2.1.2 Configuration of Multi-Carrier O(4), Multi-Carrier O(5), and Multi-carrier O(6)..........6
2.1.3 Configuration of Single-Carrier S(1/1/1), Multi-Carrier S(2/2/2) and Multi-Carrier
S(3/3/3)..................................................................................................................................6
2.1.4 Configuration of Multi-Carrier S(4/4/4), Multi-Carrier S(5/5/5) and Multi-Carrier
S(6/6/6)..................................................................................................................................7
2.2 Hybrid Configuration of Single Carrier and Multi-Carrier.......................................................8
2.2.1 Hybrid Configuration of the CTRM and CMTR............................................................8
2.2.2 Hybrid Configuration of the HPA and TRM..................................................................9
Chapter 3 Hardware and Software Configuration of Multi-carrier............................................10
3.1 Software Configuration.........................................................................................................10
3.2 Hardware Configuration........................................................................................................10
Chapter 4 Configuration of Multi-Carrier BTS............................................................................11
4.1 Key Points of Data Configuration..........................................................................................11
4.1.1 Resource Pool............................................................................................................11
4.1.2 TRM Configuration......................................................................................................11
4.1.3 Combined Cabinet Configuration...............................................................................11
4.2 Configuration Examples (Configuration of Key Point).........................................................12
4.2.1 O1 Configuration........................................................................................................12
4.2.2 O3 Configuration........................................................................................................13
4.2.3 O4 Configuration........................................................................................................13
4.2.4 O6 Configuration........................................................................................................14
4.2.5 S111 Configuration.....................................................................................................15
4.2.6 S333 Configuration.....................................................................................................16
4.2.7 S444 Configuration.....................................................................................................17
4.2.8 S666 Configuration.....................................................................................................19
Chapter 5 Features of Multi-Carrier Power.................................................................................23
5.1 Allocation of Multi-Carrier Power..........................................................................................23
5.2 CMPA Overdrive Threshold..................................................................................................23
5.3 Multi-Carrier Power Tracing..................................................................................................24
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Chapter 6 Multi-Carrier BTS Calibration.....................................................................................26
Chapter 7 Limitation on Multi-Carrier System............................................................................27
7.1 One Cell of Multi-Carrier BTS...............................................................................................27
7.2 Multi-channel Carrier Board..................................................................................................27
Chapter 8 Fault Location.............................................................................................................. 28
8.1 Forward Power Abnormal.....................................................................................................28
8.2 Reverse Channel Abnormal..................................................................................................28
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Guide to Multi-Carrier CDMA2000 BTS3606
Key words: 3606, multi-carrier, CMTR, CTRM, CHPA, CMPA
Abstract: This guide describes the development and maintenance personnel to use
multi-carrier cBTS3606.
Abbreviations:
Abbreviations
Full spelling
CTRM
Compact-BTS Transceiver Module
CMTR
Compact-BTS Multi-carrier Transceiver Module
CHPA
Compact-BTS High power Amplifier
CMPA
Compact-BTS Multi-carrier Power Amplifier
CCPM
Compact-BTS Channel Process Module
CECM
Compact-BTS EVDO Channel Module
Reference
Manual of 31161592-bts3606&3606a Data Configuration (V2.12)
Installation Manual of 31041702-bts3606&3606a BTS Installation Reference (V2.12)
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Chapter 1 Overview
The Multi-carrier cBTS3606 is developed to expand the capacity and improve the
flexibility of the CDMA. This chapter introduces the new function of multi-carrier
cBTS3606. It enables the operator to add the number of sector carriers only by
upgrading software and modifying configuration (no need to add hardware for a single
cabinet). Thus, the capacity is expanded.
The TRM (CMTR) of each multi-carrier supports three carriers (three different channel
numbers at the same band class) at most. That is, CBTS3606 supports three times
capacity of the original multi-carrier at most and supports CDMA2000 1X and
cdma2000 1xEV-DO.
The single cabinet of the CBTS3606 with the full configuration S (6/6/6) supports 18
sector carriers at most.
shows the cabinet of multi-carrier cBTS3606.
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
2005-08-01
All rights reversed
Confidentiality level
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Figure 1.1 Cabinet of multi-carrier cBTS3606
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Chapter 2 Installation
This chapter describes how to install the multi-carrier cBTS3606.
2.1 Cable Connection of Typical Configurations
This section describes cables connection of some typical configurations.
2.1.1 Configuration of Single Carrier O(1), Multi-Carrier O(2), and MultiCarrier O(3)
Figure 1.1 shows the configuration of the RF cable of the single carrier O(1), multicarrier O(2), and multi-carrier O(3).
The cable connection of the previous three configurations is the same; however, they
are different only in setting the software parameters.
Sect or A
Sect or B
Sect or C
CDDU
CMPA
RF_out
RF_in
Sample
Figure 1.1
TX
1
RX
1
TX
2
RX
2
CMTR
DR
I
MR
I
MRO
TX
TXF
Configuration of single carrier O(1), multi-carrier O(2), and multi-carrier O(3)
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
2.1.2 Configuration of Multi-Carrier O(4), Multi-Carrier O(5), and Multi-carrier
O(6)
Figure 1.1 shows the configuration of the RF cable of the multi-carrier O(4), multicarrier O(5), and multi-carrier O(6).
The cable connection of the previous three configurations is the same; however, they
are different only in setting the software parameters.
Sect or A
CDDU
CMPA
RF_out
RF_in
Sample
CMPA
RF_out
RF_in
Sample
TX1
RX1
TX2
RX2
CMTR
DRI
MRI
MRO
TX
TXF
CMTR
DRI
MRI
MRO
TX
TXF
Figure 1.1 Configuration of multi-carrier O(4), multi-carrier O(5), and multi-carrier
O(6)
2.1.3 Configuration of Single-Carrier S(1/1/1), Multi-Carrier S(2/2/2) and
Multi-Carrier S(3/3/3)
Figure 1.1 shows the configuration of the RF cable of the single-carrier S(1/1/1),
multi-carrier S(2/2/2), and multi-carrier S(3/3/3).
The cable connection of the previous three configurations is the same; however, they
are different only in setting the software parameters.
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Sect or A
Sect or B
Sect or C
CDDU
CDDU
CDDU
TX1
RX1
TX1
RX1
TX1
RX1
TX2
RX2
TX2
RX2
TX2
RX2
CMPA
RF_out
RF_in
Sample
CMTR
DRI
MRI
MRO
TX
TXF
CMPA
CMTR
DRI
RF_out
RF_in
Sample
MRI
MRO
TX
TXF
CMPA
RF_out
RF_in
CMTR
DRI
MRI
MRO
TX
Sample
TXF
Figure 1.1 Configuration of single-carrier S(1/1/1), multi-carrier S(2/2/2), and multicarrier S(3/3/3)
2.1.4 Configuration of Multi-Carrier S(4/4/4), Multi-Carrier S(5/5/5) and MultiCarrier S(6/6/6)
Figure 1.1 shows the configuration of the RF cable of the multi-carrier S(4/4/4), multicarrier S(5/5/5) and multi-carrier S(6/6/6).
The cable connection of the previous three configurations is the same; however, they
are different only in setting the software parameters.
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Sect or
A
Confidentiality level
Sect or
B
Sect or
CDDU
CDDU
C
CDDU
TX1
RX1
TX1
RX1
TX1
RX1
TX2
RX2
TX2
RX2
TX2
RX2
CMPA
RF_out
RF_in
Sample
CMPA
RF_out
RF_in
Sample
CMTR
DRI
MRI
MRO
TX
TXF
CMTR
DRI
MRI
MRO
TX
TXF
CMPA
CMTR
DRI
RF_out
MRI
MRO
RF_in
CMTR
DRI
RF_out
MRI
MRO
RF_in
TX
Sample
CMPA
CMPA
TXF
CMTR
DRI
RF_out
RF_in
MRI
MRO
TX
Sample
TXF
TX
Sample
CMPA
TXF
CMTR
DRI
RF_out
MRI
MRO
RF_in
TX
Sample
TXF
Figure 1.1 Configuration of the multi-carrier S(4/4/4), multi-carrier S(5/5/5) and multicarrier S(6/6/6).
2.2 Hybrid Configuration of Single Carrier and Multi-Carrier
The hybrid configuration of single carrier and multi-carrier helps when handover or
emergency occurs. The hybrid configuration of single carrier and multi-carrier
indicates:
Both the TRM (CTRM) of single carrier and multi-carrier can be used in multicarrier cabinet. The TRM (CTRM) of single carrier is only configured with the
CHPA of single carrier and the TRM (CTRM) of multi-carrier is only configured
with the CMPA of multi-carrier.
The TRM (CTRM) of single carrier is configured with the CMPA of multi-carrier or
the TRM (CMTR) of multi-carrier is configured with the CHPA of single carrier in
a multi-carrier cabinet.
2.2.1 Hybrid Configuration of the CTRM and CMTR
The CTRM can be configured with the CMTR. If the two boards that connect to the
CDDU are
Both CTRMs, the sector supports two carriers at most.
One CTRM and one CMTR, the sector supports four carriers at most.
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Both CMTRs, the sector supports six carriers at most.
2.2.2 Hybrid Configuration of the HPA and TRM
The CTRM can be configured with the CMPA.
If the CMTR is configured with the CHPA, one carrier is supported (this method is not
recommended). This carrier must be provided by the CCPM/CECM 0 and
CCPM/CECM 1.
In all, if the type of TRM and HPA do not match each other, the TRM can only support
one carrier.
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Chapter 3 Hardware and Software Configuration
of Multi-carrier
This chapter describes the hardware and software configuration of multi-carrier.
3.1 Software Configuration
The software of V200R001C04 or higher versions support multi-carrier.
3.2 Hardware Configuration
The requirements for the hardware are as follows:
The BTS3606 multi-carrier cabinet with six CCPM slots support multi-carrier. The
BTS3606 single-carrier cabinet with four CCPM slots do not support multi-carrier.
Currently, only a few BTS3606 cabinets with four CCPM slots are used.
ODU3601C does not support multi-carrier.
For hardware configuration of other boards, see the version configuration table of
each product.
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
Chapter 4 Configuration of Multi-Carrier BTS
This chapter describes how to configure the multi-carrier BTS.
4.1 Key Points of Data Configuration
This section describes the key points of data configuration.
4.1.1 Resource Pool
Multi-carrier BTS supports resource pool. Two CCPMs are configured in each
resource pool at most. The resource pool is composed of the upper and lower
CCPMs.
If two CCPMs are in the resource pool, this resource pool only supports the TRM in
one RF subrack. Carriers provided by the resource pool are as follows:
The resource pool composed of CCPM 0/CCPM 1 provides the first carrier to all
the TRMs of the corresponding RF subrack.
The resource pool composed of CCPM 2/CCPM 3 provides the second carrier to
all the TRMs of the corresponding RF subrack.
The resource pool composed of CCPM 4/CCPM 5 provides the third carrier to all
the TRMs of the corresponding RF subrack.
4.1.2 TRM Configuration
To configure a TRM, the following items are included:
Configuring the physical TRM.
Specifying the sector carrier on certain carrier of the TRM. Use the parameter
[TRM, CPLID] to identify this carrier.
4.1.3 Combined Cabinet Configuration
The combined cabinet is used to support multiple band classes in one BTS. If the
parameter EXTFIBPN is specified in CCPM configuration, the combined cabinet is
configured
To configure the combined cabinet, pay attention to the following items:
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
The channel unit connected to the LECM is configured in the lower part of the
main cabinet (slot1, slot3, and slot 5).
The LECM is consistent with the channel unit slot connected to the LECM. The
mapping is as follows:
Slot 0: channel unit 1
Slot 2: channel unit 3
Slot 4: channel unit 5
The channel unit used for the combined cabinet cannot be used for the TRM or
ODU of the main cabinet, and do not support the daisy chain.
4.2 Configuration Examples (Configuration of Key Point)
The following describes how to configure the key points of the multi-carrier BTS with
the software of the CBTS3606 V200R001C04 as an example.
Note:
For the configuration of the other parts, see Appendix BTS Configuration Script.
Pay more attention to the words in red.
Typical configuration script refer to the Accessory.
4.2.1 O1 Configuration
The O1 configuration includes three parts:
To configure the channel unit, execute the following command.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
To configure the TRM, execute the following command.
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”TRM
1”;
To specify the sector carrier on certain carrier of the TRM, execute the following
command.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
4.2.2 O3 Configuration
The O3 configuration includes three parts:
To configure the channel unit, execute the following commands.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
ADD CBTSCCPM:BTSID=1,BRDID=2,CPLID=1;
ADD CBTSCCPM:BTSID=1,BRDID=4,CPLID=2;
To configure the TRM, execute the following command.
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”CMT
R1”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
1,TRMID=1,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
2,TRMID=1,CPLID=2;
4.2.3 O4 Configuration
The O4 configuration includes three parts:
To configure the resource channel, execute the following commands.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
ADD CBTSCCPM:BTSID=1,BRDID=2,CPLID=1;
ADD CBTSCCPM:BTSID=1,BRDID=1,CPLID=2;
ADD CBTSCCPM:BTSID=1,BRDID=3,CPLID=3;
To configure the TRM, execute the following commands.
ADD
CBTSTRM:BTSID=1,TRMID=0,RCKTP=MASTER,SN=0,DUPSN=0,TRMDES=”CMT
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
R0”;
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”CMT
R1”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
1,TRMID=1,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
2,TRMID=0,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
3,TRMID=0,CPLID=3;
4.2.4 O6 Configuration
The O6 configuration includes three parts:
To configure the channel unit, execute the following commands.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
ADD CBTSCCPM:BTSID=1,BRDID=2,CPLID=1;
ADD CBTSCCPM:BTSID=1,BRDID=4,CPLID=2;
ADD CBTSCCPM:BTSID=1,BRDID=1,CPLID=3;
ADD CBTSCCPM:BTSID=1,BRDID=3,CPLID=4;
ADD CBTSCCPM:BTSID=1,BRDID=5,CPLID=5;
To configure the TRM, execute the following commands.
ADD
CBTSTRM:BTSID=1,TRMID=0,RCKTP=MASTER,SN=0,DUPSN=0,TRMDES=”CMT
R0”;
ADD
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”CMT
R1”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
1,TRMID=1,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
2,TRMID=1,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
3,TRMID=0,CPLID=3;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
4,TRMID=0,CPLID=4;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
5,TRMID=0,CPLID=5;
4.2.5 S111 Configuration
The S111 configuration includes three parts:
To configure the channel unit, execute the following command.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
To configure the TRM, execute the following commands.
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”TRM
1”;
ADD
CBTSTRM:BTSID=1,TRMID=3,RCKTP=MASTER,SN=3,DUPSN=1,TRMDES=”TRM
3”;
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
ADD
CBTSTRM:BTSID=1,TRMID=5,RCKTP=MASTER,SN=5,DUPSN=2,TRMDES=”TRM
5”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
0,TRMID=3,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
0,TRMID=5,CPLID=0;
4.2.6 S333 Configuration
The S333 configuration includes three parts:
To configure the channel unit, execute the following commands.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
ADD CBTSCCPM:BTSID=1,BRDID=2,CPLID=1;
ADD CBTSCCPM:BTSID=1,BRDID=4,CPLID=2;
To configure the TRM, execute the following commands.
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”TRM
1”;
ADD
CBTSTRM:BTSID=1,TRMID=3,RCKTP=MASTER,SN=3,DUPSN=1,TRMDES=”TRM
3”;
ADD
CBTSTRM:BTSID=1,TRMID=5,RCKTP=MASTER,SN=5,DUPSN=2,TRMDES=”TRM
5”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
1,TRMID=1,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
2,TRMID=1,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
0,TRMID=3,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
1,TRMID=3,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
2,TRMID=3,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
0,TRMID=5,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
1,TRMID=5,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
2,TRMID=5,CPLID=2;
4.2.7 S444 Configuration
The S444 configuration includes three parts:
To configure the resource pool, execute the following commands.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
ADD CBTSCCPM:BTSID=1,BRDID=2,CPLID=1;
ADD CBTSCCPM:BTSID=1,BRDID=1,CPLID=2;
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
ADD CBTSCCPM:BTSID=1,BRDID=3,CPLID=3;
To configure the TRM, execute the following commands.
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”TRM
1”;
ADD
CBTSTRM:BTSID=1,TRMID=3,RCKTP=MASTER,SN=3,DUPSN=1,TRMDES=”TRM
3”;
ADD
CBTSTRM:BTSID=1,TRMID=5,RCKTP=MASTER,SN=5,DUPSN=2,TRMDES=”TRM
5”;
ADD
CBTSTRM:BTSID=1,TRMID=0,RCKTP=MASTER,SN=0,DUPSN=0,TRMDES=”TRM
0”;
ADD
CBTSTRM:BTSID=1,TRMID=2,RCKTP=MASTER,SN=2,DUPSN=1,TRMDES=”TRM
2”;
ADD
CBTSTRM:BTSID=1,TRMID=4,RCKTP=MASTER,SN=4,DUPSN=2,TRMDES=”TRM
4”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
1,TRMID=1,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
0,TRMID=3,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
1,TRMID=3,CPLID=1;
ADD
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
0,TRMID=5,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
1,TRMID=5,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
2,TRMID=0,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
3,TRMID=0,CPLID=3;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
2,TRMID=2,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
3,TRMID=2,CPLID=3;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
2,TRMID=4,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
3,TRMID=4,CPLID=3;
4.2.8 S666 Configuration
The S666 configuration includes three parts:
To configure the channel unit, execute the following commands.
ADD CBTSCCPM:BTSID=1,BRDID=0,CPLID=0;
ADD CBTSCCPM:BTSID=1,BRDID=2,CPLID=1;
ADD CBTSCCPM:BTSID=1,BRDID=4,CPLID=2;
ADD CBTSCCPM:BTSID=1,BRDID=1,CPLID=3;
ADD CBTSCCPM:BTSID=1,BRDID=3,CPLID=4;
ADD CBTSCCPM:BTSID=1,BRDID=5,CPLID=5;
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
To configure the TRM, execute the following commands.
ADD
CBTSTRM:BTSID=1,TRMID=1,RCKTP=MASTER,SN=1,DUPSN=0,TRMDES=”TRM
1”;
ADD
CBTSTRM:BTSID=1,TRMID=3,RCKTP=MASTER,SN=3,DUPSN=1,TRMDES=”TRM
3”;
ADD
CBTSTRM:BTSID=1,TRMID=5,RCKTP=MASTER,SN=5,DUPSN=2,TRMDES=”TRM
5”;
ADD
CBTSTRM:BTSID=1,TRMID=0,RCKTP=MASTER,SN=0,DUPSN=0,TRMDES=”TRM
0”;
ADD
CBTSTRM:BTSID=1,TRMID=2,RCKTP=MASTER,SN=2,DUPSN=1,TRMDES=”TRM
2”;
ADD
CBTSTRM:BTSID=1,TRMID=4,RCKTP=MASTER,SN=4,DUPSN=2,TRMDES=”TRM
4”;
To specify the sector carrier on certain carrier of the TRM, execute the following
commands.
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
0,TRMID=1,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
1,TRMID=1,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
2,TRMID=1,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
0,TRMID=3,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
2005-08-01
All rights reversed
Page 3 of 33
Guide to Multi-Carrier CDMA2000 BTS3606
Confidentiality level
1,TRMID=3,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
2,TRMID=3,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
0,TRMID=5,CPLID=0;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
1,TRMID=5,CPLID=1;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
2,TRMID=5,CPLID=2;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
3,TRMID=0,CPLID=3;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
4,TRMID=0,CPLID=4;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=0,CRRID=
5,TRMID=0,CPLID=5;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
3,TRMID=2,CPLID=3;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
4,TRMID=2,CPLID=4;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=1,CRRID=
5,TRMID=2,CPLID=5;
ADD
CBTSSECTORCARRIER:BTSID=1,LOCALCELLID=6,LOCALSECTORID=2,CRRID=
3,TRMID=4,CPLID=3;
2005-08-01
All rights reversed
Page 3 of 33
