NHÀ MÁY SẢN XUẤT CLINKER VĂN HÓA
P. SỬA CHỮA CƠ ĐIỆN
TÀI LIỆU
NGUYÊN LÝ HOẠT ĐỘNG
LỰC MÁY NGHIỀN ĐỨNG PF
Hoàng Minh Thắng
HỆ THỐNG THỦY LỰC NGHIỀN LIỆU KIỂU
ĐỨNG MPS 5000B PFEIFFER
GiỚI THIỆU CHUNG
Trong công nghiệp sản xuất vật liệu xây dựng thì máy nghiên luôn có vai trò vô
cùng quan trong.
• Điển hình trong công nghiệp sản xuất xi măng thì máy nghiền càng đóng vai trò
cực kỳ quan trọng trong việc đảm bảo năng suất của lò nung cũng như quá trình
hoạt động của toàn bộ dây chuyền.
• Máy nghiền đứng ngày nay đang được sử dụng rộng rãi ở nước ta vì vậy việc
vận hành và sửa chửa máy khi bị sự cố là điều mà các kỹ sư bảo trì luôn quan tâm
và tìm hiểu.
• Cùng với nhiều hãng máy nghiền nỗi tiếng của châu âu thì máy nghiền đứng
Pfeiffer của Đức là một trong những máy nghiền mà ở Việt Nam đang vận hành.
• Hệ thống thủy lực của máy nghiền đứng là một trong những hệ thống quan trọng
và phức tạp nhất của máy. Muốn bảo trì xử lý sự cố thì mọi kỹ sư cần phải nắm rõ
nguyên lý điều khiển hoạt động của hệ thống thủy lực đầu tiên.
• Tài liệu này trình bày nguyên lý hoạt động của hệ thống thủy lực máy nghiền
liệu Pferffer MPS 5000B.
• Tài liệu này được các kỹ sư của nhà máy VCM Văn Hóa Quảng Bình tìm hiểu và
biên soạn nhằm phục vụ quá trình duy tu bão dưỡng cũng như xử lý sự cố.
Hệ thống thủy lực máy nghiền liệu kiểu
đứng của Pfeiffer MPS 5000B có 5
sequence điều khiển chính
Sequence 1: Tạo áp nén trước khi nâng
Sequence 2: Nâng con lăn và khung tam giác dưới áp suất
nén
Sequence 3: Cân bằng hệ thống con lăn trong quá trình
nâng
Sequence 4: Hạ con lăn
Sequence 5: Hệ thống thủy lực làm việc có tải
All valves de-energized
Trạng thái khi chưa cấp điện
điều khiển cho các van
Tension hydraulic sequence 1
Build-up pre-tension pressure
P3 < 10 bar
P0 = Accumulator charging
pressure
P1 = Operating pressure-tighten
P3 = Lifting pressure
Green:
Blue:
Orange:
Pink:
Valves energizer
Pump switched on
Back Valves Open
Main oil flow
Control oil flow
Return oil flow
Over pressure oil flow
SP Press =P0 *1.7 Bar
Tension hydraulic sequence 2
Lift up pressure frame with
roller under pre-tension
pressure
P1 < 60 Bar
P0 = Accumulator charging
pressure
P1 = Operating pressure-tighten
P3 = Lifting pressure
Green:
Blue:
Orange:
Pink:
Valves energizer
Pump switched on
Main oil flow
Control oil flow
Return oil flow
Over pressure oil flow
P1 >= 40 Bar
P0 = Accumulator charging
pressure
P1 = Operating pressure-tighten
P3 = Lifting pressure
Green:
Blue:
Orange:
Pink:
Valves energizer
Pump switched on
Main oil flow
Control oil flow
Return oil flow
Over pressure oil flow
Tension hydraulic sequence 2
- Lift up pressure frame with
roller under pre-tension
pressure
- 2.2 first lift up of rollers
- 2.3 lift up rollers again after
pressure loss
Tension hydraulic sequence 3
- Rollers are equally lifted
levelling is finished
- 2.4 start corrective actions
during lift up process
P0 = Accumulator charging
pressure
P1 = Operating pressure-tighten
P3 = Lifting pressure
Green:
Blue:
Orange:
Pink:
Dark Red
Valves energizer
Pump switched on
Main oil flow
Control oil flow
Return oil flow
Over pressure oil flow
Balance pressure frame oil flow
Tolerance for position Cylinder
1,2,3: 3 mm
Tension hydraulic sequence 4
Lower pressure frame with
rollers under pre-tension
pressure
P0 = Accumulator charging
pressure
P1 = Operating pressure-tighten
P3 = Lifting pressure
Green:
Blue:
Orange:
Pink:
Valves energizer
Pump switched on
Main oil flow
Control oil flow
Return oil flow
Over pressure oil flow
Finished: P3 < 10 bar
Tension hydraulic sequence 5
Build-up operating tension
pressure for meal operation of
the mill
P0 = Accumulator charging
pressure
P1 = Operating pressure-tighten
P3 = Lifting pressure
Green:
Blue:
Orange:
Pink:
Valves energizer
Pump switched on
Back Valves Open
Main oil flow
Control oil flow
Return oil flow
Over pressure oil flow
O
Y
K
N
HA
R
O
UF
E
T
AT
C
N
A
D
N