Tài liệu Reinforcing the Cabinet pptx

OptiX OSN 3500
Installation Manual Contents
Contents
5 Reinforcing the Cabinet 1
5.1 Combining the Adjacent Cabinets 2
5.2 Reinforcing the Cabinet to the Cabling Frame 4
5.2.1 Reinforcement Mode 4
5.2.2 Reinforcing the Cabinet by Method 1 5
5.2.3 Reinforcing the Cabinet by Method 2 8
5.2.4 Reinforcing the Cabinet by Method 3 10
5.2.5 Reinforcing the Cabinet by Method 4 12
5.3 Checking the Installation 14
Issue 05 (2006-11-20)
Huawei Technologies Proprietary
i
Figures
Position of joint plates 2
Combining the adjacent cabinets 3
Installation mode 4
Reinforcing the cabinet by method 1 6
Expected result 7
Reinforcing the cabinet by method 2 9
Expected result 10
Reinforcing the Cabinet by Method 3 11
Expected result 12
Reinforcing the cabinet by method 4 13
Expected result 14
T2-0416xx-
20050330-C-
1.20
Huawei

Technologies
Proprietary
iii
5 Reinforcing the Cabinet
About This Chapter
This chapter guides you to reinforce the installed cabinets. For stability purpose,
cabinets must be reinforced by the following methods.

Combining the adjacent cabinets with joint plates.

Reinforcing the cabinet to the cabling frame.
The following table lists the contents of this chapter.
Section Description
5.1Combining the Adjacent
Cabinets
Describes operations and procedures of combining the
adjacent cabinets.
5.2Reinforcing the Cabinet to
the Cabling Frame
Describes operations and procedures of installing the
cabinet shockproof components.
5.3Checking the Installation Describes the checklist of the installation.
T2-0416xx-
20050330-C-
1.20
Huawei
Technologies
Proprietary
1
5 Reinforcing the Cabinet

OptiX OSN 3500
Installation Manual
5.1 Combining the Adjacent Cabinets
Purpose
This procedure guides you to combine the adjacent cabinets
with joint plates.
Tools /Materials
Joint plate
Cross screwdriver
Prerequisites
The installation of cabinets is finished.
Required/As
needed
As needed.
 Note
The adjacent cabinets must be combined with joint plates. Two joint plates are
delivered with every cabinet.
Step 1 Remove the joint plate from the top of the cabinet. Before delivery, the joint
plates have been attached to the cabinet. See Figure 1.1.
Joint plate
Figure 1.1 Position of joint plates
Step 2 Insert the M5 x 10 tapping screws into the joint plate and further into screw holes
on the top of the two adjacent cabinets. Screw them tight to fix the joint plate. See
Figure 1.1.
2
Huawei Technologies Proprietary
Issue 05 (2006-11-20)
OptiX OSN 3500
Installation Manual 5 Reinforcing the Cabinet
Figure 1.1 Combining the adjacent cabinets

End
Issue 05 (2006-11-20)
Huawei Technologies Proprietary
3
5 Reinforcing the Cabinet
OptiX OSN 3500
Installation Manual
5.2 Reinforcing the Cabinet to the Cabling
Frame
This section guides you to reinforce a cabinet to the cabling frame.
5.2.1 Reinforcement Mode
Select an installation mode according the following items:

Whether there are troughs at sides of the cabling frame.

The height the cabinet.
Figure 1.1 shows the selection of installation mode.
Start
Any trough at
cabling frame
side?
No
2600mm-high
cabinet?
2600mm-high
cabinet?
Yes
No
End
Yes

No
Yes
Reinforcing a
2600mm-high
cabinet
(Method 1)
Reinforcing a
2200mm-high or
2000mm-high
cabinet
(Method 2)
Reinforcing a
2600mm-high
cabinet
(Method 3)
Reinforcing a
2200mm-high or
2000mm-high
cabinet
(Method 4)
Figure 1.1 Installation mode
4
Huawei Technologies Proprietary
Issue 05 (2006-11-20)
OptiX OSN 3500
Installation Manual 5 Reinforcing the Cabinet
5.2.2 Reinforcing the Cabinet by Method 1
Purpose
This procedure guides you to reinforce the cabinets to the
cabling frame.

Tools /Materials
Fixing bracket
Insulation plate
Diamond-shaped nut
M8 x 20 bolt
M8 x 25 bolt
Prerequisites
The cabinets have been installed already.
The cabling frame has been installed.
The cabinet is 2600 mm high.
The cabling frame has side troughs.
Required/As
needed
As needed.
Step 1 Determine where to install the fixing part according to positions of the installed
cabinet and the cabling frame.
Step 2 Place the diamond-shaped nut into the trough of the cabling frame.
Step 3 Place a spring washer and a flat washer onto the M8 x 20 bolt.
Step 4 Insert the bolt assembly through the fixing bracket and screw the bolt into the
diamond-shaped nut in the trough of the cabling frame. See Step 7Figure 1.1.
 Note
Do not screw the bolt too tight. Screw it until the bolt cannot fall out.
Step 5 Place an insulation plate between the cabinet and the fixing bracket.
Step 6 Place a spring washer, a big flat washer and an insulation washer onto the M8 x
25 bolt.
Step 7 Insert the bolt assembly through the fixing bracket and insulation plate, and into
the nut on the cabinet. See Figure 1.1.
Issue 05 (2006-11-20)
Huawei Technologies Proprietary
5

5 Reinforcing the Cabinet
OptiX OSN 3500
Installation Manual
 Note
Do not screw the bolt too tight. Screw it until the bolt cannot fall out.
1
4
5
3
7
6
2
1.Cabinet 2. Cabling frame 3. Diamond-shaped nut
4. Fixing bracket 5. M8 x 20 bolt 6. M8 x 25 bolt
7. Insulation plate
Figure 1.1 Reinforcing the cabinet by method 1
Step 8 Install other fixing parts, and adjust their relative positions according to the on-
site engineering situation. Then screw all bolts tight. See Figure 1.1.
6
Huawei Technologies Proprietary
Issue 05 (2006-11-20)
OptiX OSN 3500
Installation Manual 5 Reinforcing the Cabinet


Figure 1.1 Expected result
End
Issue 05 (2006-11-20)
Huawei Technologies Proprietary
7

5 Reinforcing the Cabinet
OptiX OSN 3500
Installation Manual
5.2.3 Reinforcing the Cabinet by Method 2
Purpose
This procedure guides you to reinforce the cabinets to the
cabling frame.
Tools /Materials
Fixing bracket
Insulation plate
Diamond-shaped nut
M8 x 20 bolt
M8 x 25 bolt
Prerequisites
The cabinets have been installed already.
The cabling frame has been installed.
The cabinet is 2200mm or 2000mm high.
The cabling frame has side troughs.
Required/As
needed
As needed
Step 1 Determine where to install the fixing part according to positions of the installed
cabinet and the cabling frame.
Step 2 Adjust the height of the adjustable bracket according to the distance between the
cabinet and the cabling frame.
Step 3 Place the diamond-shaped nut into the determined position in the trough of the
cabling frame.
Step 4 Place a spring washer and a flat washer onto the M8 x 20 bolt.
Step 5 Insert the bolt assembly through the adjustable bracket, and into the diamond-
shaped nut in the trough of the cabling frame.

Step 6 Insert another M8 x 20 bolt assembly through the fixing bracket and the
adjustable plate, and into the corresponding nut with moderate force.
 Note
Do not screw the bolt too tight. Screw it until the bolt cannot fall out.
Step 7 Place an insulation plate between the cabinet and the fixing bracket. See Figure
1.1.
8
Huawei Technologies Proprietary
Issue 05 (2006-11-20)
OptiX OSN 3500
Installation Manual 5 Reinforcing the Cabinet
3
4
5
7
8
6
5
1
2
1.Cabinet 2. Cabling frame 3. Diamond-shaped nut 4. Adjustable bracket
5. M8 × 20 bolt 6. Fixing bracket 7. M8 × 25 bolt 8. Insulation plate
Figure 1.1 Reinforcing the cabinet by method 2
Step 8 Place a spring washer, a big flat washer and an insulation washer onto the M8 x
25 bolt.
Step 9 Insert the bolt assembly through the fixing bracket and the insulation plate, and
into the nut on the cabinet with moderate force. See Step 7Figure 1.1.
 Note
Do not screw the bolt too tight. Screw it until the bolt cannot fall out.
Step 10 Install other fixing parts, and adjust their relative positions according to the on-

site engineering situation. Then screw all bolts tight. See Figure 1.1.
Issue 05 (2006-11-20)
Huawei Technologies Proprietary
9
5 Reinforcing the Cabinet
OptiX OSN 3500
Installation Manual


Figure 1.1 Expected result
End
5.2.4 Reinforcing the Cabinet by Method 3
Purpose
This procedure guides you to reinforce the cabinets to the
cabling frame.
Tools /Materials
Fixing bracket
Insulation plate
M8 x 50 bolt
M8 x 25 bolt
Clamp
Prerequisites
The cabinets have been installed already.
The cabling frame has been installed.
The cabinet is 2600 mm high.
The cabling frame has no side troughs.
Required/As
needed
As needed
Step 1 Determine where to install the fixing part according to positions of the installed

cabinet and the cabling frame.
Step 2 Place a spring washer and a flat washer onto the M8 x 50 bolt.
10
Huawei Technologies Proprietary
Issue 05 (2006-11-20)
OptiX OSN 3500
Installation Manual 5 Reinforcing the Cabinet
Step 3 Insert the bolt assembly through the fixing bracket and the clamp, and screw it
with moderate force. See Step 7Figure 1.1.
Step 4 Place an insulation plate between the cabinet and the fixing bracket.
Step 5 Place a spring washer, a big flat washer and an insulation washer onto the M8 x
25 bolt.
Step 6 Insert the bolt assembly through the fixing bracket and the insulation plate, and
into the nut on the cabinet with moderate force. See Step 7Figure 1.1.
 Note
Do not screw the bolt too tight. Screw it until the bolt cannot fall out.
Step 7 Install other fixing parts, and adjust their relative positions according to the on-
site engineering situation. Then screw all bolts tight. See Figure 1.2.
1
7
6
2
5
4
3
1.Cabinet 2. Cabling frame 3. Clamp 4. M8 × 50 bolt
5. Fixing bracket 6. M8 × 25 bolt 7. Insulation plate
Figure 1.1 Reinforcing the Cabinet by Method 3
Issue 05 (2006-11-20)
Huawei Technologies Proprietary

11
5 Reinforcing the Cabinet
OptiX OSN 3500
Installation Manual


Figure 1.2 Expected result
End
5.2.5 Reinforcing the Cabinet by Method 4
Purpose
This procedure guides you to reinforce the cabinets to the
cabling frame.
Tools /Materials
Fixing bracket
Insulation plate
M8 x 50 bolt
M8 x 20 bolt
M8 x 25 bolt
Clamp
Prerequisites
The cabinets have been installed already.
The cabling frame has been installed.
The cabinet is 2200mm or 2000mm high.
The cabling frame has no side troughs.
Required/As
needed
As needed
Step 1 Determine where to install the fixing part according to positions of the installed
cabinet and the cabling frame.
Step 2 Adjust the height of the adjustable bracket according to the distance between the

cabinet and the cabling frame.
12
Huawei Technologies Proprietary
Issue 05 (2006-11-20)
OptiX OSN 3500
Installation Manual 5 Reinforcing the Cabinet
Step 3 Place a spring washer and a flat washer onto the M8 ×50 bolt.
Step 4 Insert the bolt assembly through the adjustable bracket and the clamp, and screw it
with moderate force. See Step 7Figure 1.1.
Step 5 Insert the M8 x 20 bolt assembly through the fixing bracket and the adjustable
plate, and into the nut with moderate force. See Step 7Figure 1.1.
Step 6 Place a spring washer, a big flat washer and an insulation washer onto the M8 x
25 bolt.
Step 7 Insert the bolt assembly through the fixing bracket and the insulation plate, and
into the nut on the cabinet with moderate force. See Figure 1.1.
 Note
Do not screw the bolt too tight. Screw it until the bolt cannot fall out.
1
2
6
7
8
9
5
4
3
1.Cabinet 2. Cabling frame 3. Clamp 4. M8 × 50 bolt
5. Adjustable bracket 6. Fixing bracket 7. M8 x 20 8. M8 × 25 bolt 9. Insulation plate
Figure 1.1 Reinforcing the cabinet by method 4
Step 8 Install other fixing parts, and adjust their relative positions according to the on-

site engineering situation. Then screw all bolts tight. See Figure 1.1.
Issue 05 (2006-11-20)
Huawei Technologies Proprietary
13
5 Reinforcing the Cabinet
OptiX OSN 3500
Installation Manual


Figure 1.1 Expected result
End
5.3 Checking the Installation
The following requirements should be met when the cabinet is reinforced
properly.

The joint plates for combining cabinets are installed correctly and properly,
with all screws tightened.

The cabinet is stable with the fixing parts installed. If not, check whether the
bolts are screwed tight and whether correct installation mode is adopted.
14
Huawei Technologies Proprietary
Issue 05 (2006-11-20)