Tài liệu Next Generation Frame 600 mm Products Introduction pptx

10/03 • 100571
600 mm Products
2
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2
Next Generation Frame 600 mm Products
Introduction
Frames
ADC’s Next Generation Frame product line has fiber frames designed to fit a variety of termination, splice,
and storage applications. Each frame option is designed with an emphasis on superior cable management
and ease of use, including features such as ample trough space for cable and jumpers, easy access to
connectors, and storage for jumpers. The frame sections are shipped from the factory fully equipped with
all cable management hardware including a built-in jumper storage panel.
Fiber Termination Blocks (FTB)
Fiber Termination Blocks (FTBs) are available with SC, FC, ST
®
and E-2000 adapters in block configurations
of 48, 72 or 96 positions. Also, 144 position FTBs are available using LX.5
®
and LC adapters. FTBs utilize
sliding adapter packs to gain easy access to both the front and rear connectors. There is also a block
configuration available to accommodate Mini Value-Added Modules (Mini VAMs) for applications requiring
splitters or WDMs. FTBs can be ordered with or without IFC or outside plant cable.
Fiber Combination Blocks Blocks (FCB)
Fiber Combination Blocks (FCBs) provide termination and on-frame splicing capabilities, all in one block.
The block occupies two mounting positions on the frame section. They are available with SC, FC, ST
®
and
E-2000 adapters in block configurations of 48, 72 or 96 positions. Also, 144 position FCBs are available
using LX.5
®

or LC adapters.
Features and Benefits
Ample Trough Space
Reduces jumper pile-up and congestion
- Reduces maintenance time due to easy removal
and tracing of jumpers
- Minimizes risk of microbends or damage
to fiber
Built-in Jumper Storage Panel
Minimizes number of required jumper lengths
Maintains fiber bend radius
Simplifies frame installation
- Saves money by reducing the number of
different jumper lengths that have to be kept
in inventory
- Minimizes risk of microbends or damage
to fiber
Sliding Adapter Packs
Promotes high density
Provides easy access to connectors
- Saves valuable floor space
- Reduces time required for operations and
maintenance
Intelligent Cable Routing System
No fiber cross-over points
Multiple vertical troughways
- Reduces maintenance time due to easier
removal and tracing of jumpers and minimizes
fiber “weaving”
10/03 • 100571

600 mm Products
3
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
3
Next Generation Frame 600 mm Products
Fiber Main Distributing Frame (FMDF)
The FMDF is the cornerstone of the NGF product line. This innovative frame has six rear horizontal troughs.
This abundant trough space minimizes fiber pile up and congestion leading to easier jumper traceability and
removal. The frame has twelve Fiber Termination Block (FTB) mounting positions equally divided between
vertical columns on the left and right sides of the frame as shown in the figure below. The frame is 600 mm
wide x 600 mm deep. The built-in jumper storage panel will store up to 5 meters of jumper slack.
Catalog Number
NGF-ETSIMDF6060
Dimensions
2.2 m x 600 mm x 600 mm
Ordering Information
Description
600 mm FMDF frame section
600 mm 600 mm
FTB
Mounting
Position (12)
Right
Vertical
Left
Vertical
Horizontal
Trough (6)
Jumper
Storage

Panel
Front ISO View
Front View
Side View
10/03 • 100571
600 mm Products
4
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
4
Next Generation Frame 600 mm Products
Front Facing Fiber Main Distributing Frame (F3MDF)
The F3MDF is designed for single-sided access applications and may be mounted up against a wall or back-
to-back to save floor space. Unlike the FMDF, the more compact F3MDF is equipped with a single 230 mm
horizontal trough. The F3MDF has twelve FTB mounting positions equally divided between vertical columns
on the left and right sides of the frame as shown in the figure below. The frame is 600 mm wide x 480 mm
deep. The built-in jumper storage panel will store up to 5 meters of jumper slack.
2.2 m
600 mm 480 mm
Jumper
Storage
Panel
Right
Vertical
Left
Vertical
FTB
Mounting
Position (12)
Horizontal
Trough (6)

Front ISO View
Front View
Side View
Catalog Number
NGF-ETSIF3MDF6048
Dimensions
2.2 m x 600 mm x 480 mm
Ordering Information
Description
600 mm F3MDF frame section
10/03 • 100571
600 mm Products
5
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
5
2.14 m
480 mm 480 mm
FTB
Mounting
Position
Jumper
Storage
Panel
Next Generation Frame 600 mm Products
Fiber Slim Rack
The Fiber Slim Rack is designed for lower density applications than the FMDF or F3MDF. It has six FTB
mounting positions and is designed for single-sided access applications. The Slim Rack is intended for
use in a single frame application and should not be used in a multiframe lineup. The built-in jumper
storage panel will store up to 5 meters of jumper slack.
When ordering FTBs for the Slim Rack, remember that only left oriented blocks are used

on this frame.
Front ISO View
Front View
Side View
Catalog Number
NGF-SLM7A100
Dimensions
2.14 m x 480 mm x 480 mm
Ordering Information
Description
NGF Fiber Slim Rack frame section
10/03 • 100571
600 mm Products
6
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Catalog Number
NGF-TB
Block Style
1
2
3
4
1
2
4
3
SC
FC/ST
®
E-2000

LX.5
®
/LC
Cable Exit Direction
U
D
Upward
Downward
Block Configuration
A
B
C
M
48
72
96
144 (LX.5
®
or LC only)*
Block Orientation
L
R
Left
Right
Adapter Type
(62.5/125)
Multimode
9
A
5

Y
P
SC
FC
ST
®
LX.5
®
(144 only)
LC
(144 only)
OR
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N
X
K
SC ultra polish
SC ultra polish,
zirconia sleeve
SC 8° angled polish
FC ultra polish

FC ultra polish,
zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®
ultra polish
(144 only)
LX.5
®
angled polish
(144 only)
LC ultra polish
(144 only)
5
6
Next Generation Frame 600 mm Products
Fiber Termination Blocks (FTB) Unterminated
FTBs without fiber can be ordered fully loaded with adapters or empty (no adapters), in which case the
adapter packs for the block must be ordered separately (see page 12). Before ordering, determine the block
orientation and cable exit direction. Unterminated FTBs may be ordered with a “left” orientation (mounts on
the left side of the frame) or a “right” orientation (mounts on the right side of the frame). The cable exit
direction will be either “upward” (cables terminated to the rear side of the block exit up toward the top of
the frame) or “downward” (cables terminated to the rear side of the block exit down toward the bottom of
the frame). All blocks with adapters only are configured to terminate single or dual jumpers on the rear of
the block. If a multifiber breakout style cable (i.e., OSP/IFC) is to be terminated to the rear of the block, a
separate clamping kit is required (see page 7).

Definition of Variables
1
2
3
4
5
Block Style
General adapter type required in the FTB
Block Configuration
Maximum number of terminations that the FTB will accommodate when fully loaded
Block Orientation
Vertical column of the frame the FTB is to be mounted on
Cable Exit Direction
Direction the equipment jumpers or OSP cable will exit from the FTB
Adapter Type
Specific adapter type required in the FTB
* 144 blocks using style 1, 2, or 3 cannot be used
in 26" wide NGF frames
10/03 • 100571
600 mm Products
7
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
7
Next Generation Frame 600 mm Products
Fiber Termination Blocks
Clamping kit includes: Cable clamp, protective cover and fanout bracket. It is required when terminating
a multifiber breakout style cable to the rear of the block.
72 position block loaded
with jumpers
72 position block loaded with

multifiber breakout cable
72 position block with
clamping kit
Protective
Cover
Fanout
Bracket
Cable Clamping Kit
Rear Cable
Management Tray
for 144 Block
Conversion Kit
Description Catalog Number
Block style originally purchased
All 48- and 72-position blocks NGF-ACCOSPKIT02
96- or 144-position Left Up Blocks NGF-ACCRCMSLU
96- or 144-position Right Up Blocks NGF-ACCRCMSRU
96- or 144-position Left Down Blocks NGF-ACCRCMSLD
96- or 144-position Right Down Blocks NGF-ACCRCMSRD
Ordering Information
10/03 • 100571
600 mm Products
8
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
8
Next Generation Frame 600 mm Products
Fiber Termination Blocks (FTB) Preterminated
Preterminated FTBs are available with either indoor or outdoor rated cable in ribbon or stranded
configurations. All blocks are 100% factory tested to guarantee continuity and reliable connections.
Preterminated FTBs make installation quick and easy, reducing labor costs. Before ordering, determine

the block orientation and cable exit direction. Preterminated FTBs may be ordered with a “left”
orientation (mounts on the left side of the frame) or a “right” orientation (mounts on the right side of
the frame). The cable exit direction will be either “upward” (cables terminated to the rear side of the
block exit up toward the top of the frame) or “downward” (cables terminated to the rear side of the
block exit down toward the bottom of the frame).
Preterminated Fiber
Termination Blocks
arrive from the factory
with either IFC or
OSP Cables
Fiber cable easily uncoils
during installation
Fiber Termination Block
ships inside the drum
Ordering information follows on next page.
Fiber Termination Block
loaded with multifiber
breakout cable
Definition of Variables
1 Block Style
General adapter type required in the FTB
2 Block Configuration
Maximum number of terminations that the FTB will accommodate when fully loaded
3 Block Orientation
Vertical column of the frame the FTB is to be mounted on
4 Cable Exit Direction
Direction the equipment jumpers or OSP cable will exit from the FTB
5 Adapter/Connector #1
Specific adapter/connector type required in the FTB. Refers to the adapter/
connector type at the FTB

6 Connector #2
Specific connector type required at the cable end opposite the FTB
7 Cable Type
Type of cable to be terminated to the FTB
8 Cable Length
Required length of the cable terminated to the FTB
10/03 • 100571
600 mm Products
9
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
9
Catalog Number
NGF-TB
†Other cable types are available upon request.
Please contact your ACD representative.
Glass Type
Glass Type
IFC Type Multimode
(62.5/125)
OR
OR
AM
BM
DM
2M
VM
WM
YM
12-fiber stranded
24-fiber stranded

36-fiber stranded
48-fiber stranded
72-fiber stranded
96-fiber stranded
144-fiber stranded
Corning
Corning
Corning
Corning
Corning
Corning
Corning
Length in
meters
Cable Length
XXX
8
Block Style
1
2
3
4
SC
FC/ST
®
E-2000
LX.5
®
/LC
Cable Exit Direction

U
D
Upward
Downward
Block Configuration
A
B
C
M
48
72
96
144
(LX.5
®

or
LC
only)**
Block Orientation
L
R
Left
Right
1
4
2
3
IFC Type Singlemode † Glass Type
ZB

ZC
ZD
AA
BA
CA
2A
VA
DA
FH
GA
HA
MA
JA
KA
EG
FJ
72-fiber stranded
96-fiber stranded
144-fiber stranded
12-fiber stranded
24-fiber stranded
36-fiber stranded
48-fiber stranded
72-fiber stranded
96-fiber stranded
144-fiber stranded
12-fiber ribbon
24-fiber ribbon
36-fiber ribbon
48-fiber ribbon

72-fiber ribbon
96-fiber ribbon
144-fiber ribbon
House Cable*
House Cable*
House Cable*
Corning
Corning
Corning
Corning
Corning
Corning
Corning
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Sumitomo
7
OSP Cable Type Singlemode
72 fiber stranded dielectric
96-fiber ribbon dielectric
96-fiber stranded dielectric
144-fiber stranded dielectric
144-fiber ribbon dielectric
VT
VW
EN

FL
FM
Pirelli
Pirelli
Pirelli
Pirelli
Pirelli
0
9
A
5
Y
P
No connector/stub end
SC
FC
ST
®
LX.5
®

(144 only)
LC (144 only)
Connector #2 Singlemode
0
7
8
L
2
3

Q
4
V
N
X
K
No connector/stub end
SC ultra polish
SC ultra polish, zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish, zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®

ultra polish (144 only)
LX.5
®

angled polish (144 only)
LC ultra polish (144 only)
Connector #2
Multimode (62.5/125)
OR
6

OR
Adapter/Connector #1
Multimode (62.5/125)
9
A
5
Y
P
SC
FC
ST
®
LX.5
®
(144 only)
LC (144 only)
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N
X
K
SC ultra polish

SC ultra polish,
zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish,
zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®
ultra polish
(144 only)
LX.5
®
angled polish
(144 only)
LC ultra polish
(144 only)
5
Next Generation Frame 600 mm Products
Preterminated FTBs
See previous page for definition of variables.
*House cable will use Corning SMF28,
Sumitomo, Alcatel or similar singlemode
fiber based on current market availability.
** 144 blocks using style 1, 2, or 3 cannot
be used in 26" wide NGF frames

10/03 • 100571
600 mm Products
10
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
10
Next Generation Frame 600 mm Products
Fiber Combination Blocks (FCB)
Fiber Combination Blocks provide a place to terminate pigtails and splice IFC/OSP cables on the frame. The
blocks are available with several different adapter types in block configurations of 48-, 72-, or 96-positions.
Also, a 144-position FCB is available using an LX.5
®
or LC adapter. The termination portion of the fiber
combination block utilizes sliding adapter packs to gain easy access to connectors on both the front and
rear side of the block. The block is available with factory-installed pigtails for easy installation. Splice trays
are shipped with the block if ordered with pigtails; otherwise trays must be ordered separately. The block is
shipped with a cable clamp for OSP/IFC. The FCB occupies two mounting positions on a frame section.
Before ordering, determine the block orientation. FCBs may be ordered with a “left” orientation (mounts
on the left side of the frame) or a “right” orientation (mounts on the right side of the frame).
Ordering information follows on next page.
Definition of Variables
1
2
3
4
5
6
7
Block Style
General adapter type required in the FCB
Block Configuration

Maximum number of terminations that the FCB will accommodate when fully loaded
Block Orientation
Vertical column of the frame the FCB is to be mounted on
Adapter/Connector Type
Specific adapter/connector type required in the FCB
Pigtail Type
Type of pigtail required
Number of Pigtail Assemblies
Number of pigtails to be pre-installed in the FCB
Splice Chip
Type of splice chip required for splice trays
10/03 • 100571
600 mm Products
11
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
11
Catalog Number
NGF-CB
2
Splice Chip
0
1
2
3
6
7
8
9
4
Empty

Bare fusion
Heat shrink fusion
Mechanical (Elastomeric)
Nortel QPAK
Swiss
®
ANT
Rotary
FibrLok
®
16 position heat shrink fusion
Block Style
1
2
3
4
SC
FC/ST
®
E-2000
LX.5
®
/LC
Block Configuration
A
B
C
M
48
72

96
144 (LX.5
®
or LC only)
1
2
Number of Pigtail
Assemblies
XX
Number of assemblies
6
Pigtail Type
0
1
2
4
5
No pigtails
12-fiber pigtail
12-fiber stranded
Maxi-Strip
8-fiber pigtail
12-fiber ribbon
5
7
Block Orientation
L
R
Left
Right

3
A
5
9
Y
P
FC
ST
®
SC
LX.5
®
(144 only)
LC (144 only)

4
OR
Adapter/Connector Type
Multimode (62.5/125)
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N

X
K
SC ultra polish
SC ultra polish,
zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish,
zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®
ultra polish (144 only)
LX.5
®
angled polish
(144 only)
LC ultra polish (144 only)
4
1
Next Generation Frame 600 mm Products
Fiber Combination Blocks (FCB)
1
144-termination block requires the use of either:
Mechanical (elastomeric) splice tray when using mass fusion ribbon splicing
Nortel QPAK splice tray when using single fiber heat shrink fusion splicing

144 blocks using block style 1, 2, or 3 cannot be used in 26" wide NGF frames
Splice Trays For Fiber Combination Block
Catalog Number
FST - DRS
Splice Tray Type
00
FT
HS
MT
NT
ANT
RT
3M
Empty tray*
Bare fusion
Heat shrink fusion
Mechanical (elastomeric)
Nortel QPAK
Swiss ANT
Rotary
FibrLok
®
* Maximum size of chip allowed in
empty tray: .3"H x 2.5"W x 3.6"L
Note: For LX.5
®
FCB with 12 fiber ribbon
pigtails, select mechanical splicing only.
For LX.5
®

FCB with 12 fiber stranded pigtails
select Nortel QPAK (compatible with heat
shrink fusion), bare fusion or Swiss ANT only.
Number of Splices
12
24
-
12 splices
24 splices
1
2
10/03 • 100571
600 mm Products
12
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
12
48-Position
72-Position
72-Position
96-Position
96-Position
96-Position
144-Position (block code'E')
144-Position (block code'M')
SC, FC, ST
®
, E-2000
SC, E-2000
FC, ST
®

SC, E-2000
FC, ST
®
SC, FC, ST
®
, E-2000
LX.5
®
SC, FC, E-2000, LX.5
®
, LC
2 Pack / 2 Pack
2 Pack / 4 Pack
6 Pack
2 Pack / 6 Pack
8 Pack
4 Pack / 4 Pack
12 Pack
6 Pack / 6 Pack
B (shown below)
A (shown below)
E (shown below)
F (shown below)
G (shown below)
J (not shown below)
H (not shown below)
K (not shown below)
Next Generation Frame 600 mm Products
Sliding Adapter Packs
Sliding adapter packs house groups of fiber optic adapters and are mounted in Fiber Termination Blocks to

provide easy access to connectors. Sliding adapter packs are available with SC, FC, ST
®
, E-2000, LX.5
®
and
LC adapters. The adapters come in packs of two, four, six and eight depending on the adapter type and
the desired termination density. See table below for configuration guidelines.
Sliding Adapter Pack Configuration Guidelines
Block
Configuration
Adapter Type
Adapter Pack
Configuration
Adapter Pack
Option
Option A
(SC shown)
Option B
(FC shown)
Option E
(ST
®
shown)
Option F
(E-2000 shown)
Option G
(FC shown)
Option H
(LX.5
®

only)
Catalog Number
NGF- SAP
Adapter Pack Option*
A
B
E
F
G
H
J
K
2 pack/4 pack
2 pack/2 pack
6 pack
2 pack/6 pack
8 pack
12 pack (LX.5
®
block
code "E" only)
4 pack / 4 pack
6 pack / 6 pack
(all block code "M" blocks)
000
Adapter Type
Multimode
9
A
5

Y
SC
FC
ST
®
LX.5
®
(144 only)
OR
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N
X
K
SC ultra polish
SC ultra polish,zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish, zirconia sleeve
FC 8° angled polish
ST
®

ultra polish
E-2000 angled polish
LX.5
®
ultra polish (144 only)
LX.5
®
angled polish (144 only)
LC ultra polish (144 only)
5
10/03 • 100571
600 mm Products
13
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
13
Next Generation Frame 600 mm Products
Value-Added Module System Chassis
The NGF VAM chassis is designed to mount
on all standard NGF frame styles and is
interchangeable with termination, splice, and
storage modules. Each chassis accommodates
up to twelve Mini-VAM modules.
Catalog Number
Block Style
1
2
3
SC
FC/ST
E-2000

NGF - TB D
Block Orientation
L
R
Left
Right
Cable Exit Direction (Rear)
U
D
Upward
Downward
NGF VAM Chassis
* NGF VAMs with LX.5
®
or LC adapters can be placed in any of these block styles.
Please contact ADC Technical Assistance Center with any questions.
VAM Chassis
Ordering of information for value-added modules starts on page 54.
Features:
• Enclosed plug-in modules
Optical components are protected from physical and environmental damage
• Flexible platform
Modules can be created for new applications quickly and easily to meet customer requirements
• Monitor and/or test
Enables providers to troubleshoot networks without forcing disruption of service
• Custom configurations
Custom splitter configurations available upon request
ADC’s Next Generation Frame (NGF) Value-Added
Modules are designed to support emerging circuit
requirements. This high-density fiber frame solution

provides unlimited expansion while optimizing fiber
cable management. The NGF system uses Mini Value-
Added Modules to incorporate optical splitters for circuit
monitoring and video distribution. Mini Value-Added
Modules can also be configured with wavelength
division multiplexing capabilities to increase transmission
capacity over existing fiber lines. Various input and
output interface options are available.
10/03 • 100571
600 mm Products
14
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
14
Next Generation Frame 600 mm Products
Fiber Optic Terminal Jumper Storage Bay
Catalog Number
NGF-ACCFOTSB300
NGF-F3ACCFOTSB300
Dimensions
2.2 m x 300 mm x 600 mm
2.2 m x 300 mm x 480 mm
Ordering Information
Description
FOT storage bay for 600 mm
FMDF lineups
FOT storage bay for 600 mm
F3MDF lineups (not shown)
2.2 m
600 mm
300 mm

Side ViewFront ISO View Front View
(NGF-ACCFOTSB300 Shown)
10/03 • 100571
600 mm Products
15
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
15
Next Generation Frame 600 mm Products
Equipment Bay
2.2 m
600 mm
600 mm
The NGF Equipment Bay provides a mounting
location for 19-inch rack mount equipment within an
FMDF lineup. The equipment deployment in the bay
can include video transmitters, RF Splitter/Combiners,
or Remote Fiber Test Systems. NGF Equipment Bays
are available for FMDF lineups (600 mm deep) and
F3MDF lineups (480 mm deep).
NGF-ETSIEB6060-19
Catalog Number
NGF-ETSIEB6060-19
NGF-ETSIF3EB6048-19
Dimensions
2.2 m x 600 mm x 600 mm
2.2 m x 600 mm x 480 mm
Ordering Information
Description
Equipment bay for FMDF lineups
For 19" (48.26 cm) equipment

(maximum equipment width)
(36) rack unit mounting spaces
available (EIA hole spacing)
Equipment bay for F3MDF lineups
For 19" (48.26 cm) equipment
(maximum equipment width)
(36) rack unit mounting spaces
available (EIA hole spacing)
10/03 • 100571
600 mm Products
16
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
16
Next Generation Frame 600 mm Products
Accessories
Rack Installation Kits
AC Outlet Kits
Cable Clamp Kits
End Guard
The end guard provides protection for the fibers entering and exiting frames at the ends of a lineup.
Cable clamp kits are available for securing IFC/OSP cable or equipment (FOT) jumpers on the rear of the FTB.
Catalog Number
NGF-ETSIACCEG
NGF-ETSIF3ACCEG
Ordering Information
Description
FMDF end guard, 600 mm deep
F3MDF end guard, 480 mm deep
Catalog Number
NGF-ACCCLMP04

NGF-ACCCLMP08
Ordering Information
Description
Cable clamp kit for FOT patch cords
included with Fiber Termination
Blocks loaded with adapters only
Cable clamp kit for IFC/OSP cables
included with Fiber Termination
Blocks with IFC
Catalog Number
RAC-MX0616
RAC-MX0615
Ordering Information
Description
Rack installation kit for concrete
floor, kit includes:
(2) M8 bolts, 90 mm
(4) M8 nuts
(8) flat washers
(4) lock washers
shims and anchor plates
Rack installation kit for raised floor,
kit includes:
(4) threaded rods M12 x 1 m
(12) heavy nuts, lock and flat
washers
(4) nuts with springs, M12
(2) 1.8 m unistrut
(1) anchor kit
Please contact your ADC representative for catalog numbers

10/03 • 100571
600 mm Products
17
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™
Optical Distribution Frame
Introduction
Growth in the telecommunications industry has driven widespread deployment of optical fiber. As the
number of installed fibers grows, the capability of a service provider’s optical distribution frame to handle
large amounts of fiber becomes crucial. Also, office floor space is at a premium. Saving floor space by
increasing the optical distribution frame density can provide significant cost-savings to the service provider.
At the same time, service providers require a flexible optical distribution frame, which enables them to
quickly respond to the changing needs of their customers. These key factors have driven the increased
demand for a high-density, modular, front access optical distribution frame.
ADC has developed the OMX
™
optical distribution frame to meet these demands. Designed with total front
access, the OMX can be installed back-to-back or against a wall to save valuable office floor space. This
high-density frame terminates and splices up to 576 fibers in a 600 mm x 300 mm footprint and 864 in a
800 mm x 300 mm footprint. The OMX fiber frame protects fiber cable and connections through use of
ADC’s patented angled adapter/retainers and design features that maintain correct bend radius throughout
the frame. Adding signal management and enhancement functions, such as splitters, couplers and
wavelength division multiplexers, optimizes the value of your fiber network by providing nonintrusive access
to the optical signal for monitoring and testing signal integrity.
Features and Benefits
Modular solution
Provides greater flexibility for a variety of applications
- Saves costs by standardizing on one
flexible solution

High density solution
Accommodates up to 576 terminations and splices
within 600 mm x 300 mm footprint and 864 in a
800 mm x 300 mm footprint
- Saves valuable floor space
Total front access frame
Allows installation back-to-back or against a wall
- Saves valuable floor space
Superior cable management
Protects cables and connectors; reduces
reconfiguration time
- Saves maintenance costs, improves reliability
Completely enclosed and lockable
Provides additional fiber protection and security
- Improves network reliability through
controlled access to fibers
10/03 • 100571
600 mm Products
18
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™
Optical Distribution Frame
The OMX’s modular design provides flexibility to meet the specific needs of the service provider. Each
solution will be a combination of the following parts.
OMX Frame
The OMX frame is 600 mm x 300 mm and has ten mounting positions for the termination, splice and
jumper storage modules. The OMX 800 frame is 800 mm x 300 mm and also has ten mounting positions
for the termination, splice and jumper storage modules.
OMX Termination Module

The OMX termination modules are available with 72,
96, or 144 adapters. These modules can be ordered
with adapters only or preterminated with either
intrafacility fiber cable (IFC), outside plant (OSP)
cables, or pigtails for ease of installation. The
modules are available with SC, FC, ST
®
, E-2000
®
and
LX.5
®
connector/adapter styles.
OMX Splice Module
The OMX splice module provides protection and a
mounting location for ADC’s round splice trays.
Each splice module is two mounting positions tall
and holds 24 splice trays. Each splice tray can
house up to 24 splices.
OMX Slack Storage Solutions
The OMX jumper storage module enables storage of
fiber-optic jumper slack within an OMX frame. Each
jumper storage module is one module position tall.
The Interbay Management Panel provides off-frame
storage of jumper slack. ADC recommends the use of
2 mm patch cords to maximize the cable
management potential of the OMX.
10/03 • 100571
600 mm Products
19

www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™
Optical Distribution Frame
Frame Section
The OMX frame section provides mounting locations for termination, splice and storage modules. It is a
completely front-facing frame; all mounting, maintenance and cable access is done on the front of the
frame. A lower trough allows multiple frames to be mounted in a continuous lineup. The frame is shipped
with lockable front doors. Preconfigured bays are available; please contact your ADC representative for
ordering information.
OMX 600 Frame Section
Front ISO View
OMX 800 Frame Section
Front ISO View
Catalog Number
MX6-TSF6030
MX6-TSF8030
Dimensions (HxWxD)
2200 x 600 x 300 mm
2200 x 800 x 300 mm
Ordering Information
Description
OMX 600 frame section
OMX 800 frame section
10/03 • 100571
600 mm Products
20
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™

Optical Distribution Frame
Termination Module with Adapters Only
The OMX termination module with adapters only is
available with 72, 96 or 144 adapters. Modules
may be ordered with a ”left“ orientation (mounts
on the left side of the frame) or a ”right“
orientation (mounts on the right side of the frame).
ADC recommends the use of 2 mm patch cords to
maximize the cable management potential of the
OMX. Block configuration D can only be
mounted in the OMX 800.
Block Configuration
72-position
96-position
144-position (LX.5
®
only)
144-position (OMX 800 only)
A
B
C
D
Block Orientation
Left
Right
L
R
MX6-TM 0 0
OR
SC

FC
ST
®
LX.5
®
9
A
5
Y
Adapter Type Singlemode
7
L
2
Q
4
V
X
8
3
Ultra PCSC
Angled SC 8°
Ultra PCFC
Angled FC 8°
Ultra PCST
Angled E-2000 8°
LX.5
®
Ultra PCSC, zirconia sleeve
Ultra PCFC, zirconia sleeve
Adapter Type Multimode (62.5/125)

Catalog Number
72 position
10/03 • 100571
600 mm Products
21
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™
Optical Distribution Frame
Termination Module with Pigtails
The OMX preterminated pigtail modules are
available with either stranded or ribbon
preterminated fiber bundles. The modules are
mounted on the frame and the fiber bundles are
then routed directly to the splice section of the
OMX frame. This makes installation of the
modules quick and easy, saving valuable
installation time. Preterminated pigtail modules
may be ordered with a ”left“ orientation (mounts
on the left side of the frame) or a ”right“
orientation (mounts on the right side of the
frame). ADC recommends the use of 2 mm patch
cords to maximize the cable management
potential of the OMX. Block configuration D
can only be mounted in the OMX 800.
Block Configuration
72-position
96-position
144-position (LX.5
®

only)
144-position (OMX 800 only)
A
B
C
D
Block Orientation
Left
Right
L
R
MX6-PM 0
OR
SC
FC
ST
®
LX.5
®
9
A
5
Y
Connector Type Singlemode
7
L
2
Q
4
V

X
8
3
Ultra PCSC
Angled SC 8°
Ultra PCFC
Angled FC 8°
Ultra PCST
Angled E-2000 8°
LX.5
®
Ultra PCSC, zirconia sleeve
Ultra PCFC, zirconia sleeve
Connector Type Multimode (62.5/125)
Number of Pigtail Assemblies
Number of assemblies
XX
Pigtail Type
12-fiber stranded
12-fiber stranded Maxi-Strip
12-fiber ribbon
8-fiber stranded
8-fiber ribbon
6-fiber ribbon
4-fiber ribbon
6-fiber stranded
1
2
3
4

5
6
7
8
Catalog Number
96 position
10/03 • 100571
600 mm Products
22
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™
Optical Distribution Frame
Termination Module with IFC
The OMX preterminated IFC modules are available with
either indoor or outdoor rated cable in ribbon, stranded,
loose tube, or Maxi-Strip configurations. All modules are
100% factory tested to guarantee continuity and reliable
connections. IFC modules make installation quick and
easy, reducing labor costs. IFC modules may be ordered
with a ”left“ orientation (mounts on the left side of the
frame) or a ”right“ orientation (mounts on the right side
of the frame). ADC recommends the use of 2 mm patch
cords to maximize the cable management potential of
the OMX. Block configuration D can only be
mounted in the OMX 800.
96 position
MX6-FM

OR

12-fiber stranded
24-fiber stranded
36-fiber stranded
48-fiber stranded
54-fiber stranded
72-fiber stranded
96-fiber stranded
144-fiber stranded
12-fiber ribbon
24-fiber ribbon
36-fiber ribbon
48-fiber ribbon
72-fiber ribbon
96-fiber ribbon
144-fiber ribbon
72-fiber ribbon
96-fiber ribbon
144-fiber ribbon
72-fiber stranded Maxi-Strip
96-fiber stranded Maxi-Strip
IFC Type Singlemode (Indoor)
AA
BA
CA
2A
7A
VA
DA
FH
GA

HA
MA
JA
KA
EG
FJ
KB
EF
FK
MX
GF
Corning
Corning
Corning
Corning
Corning
Corning
Corning
Corning
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Sumitomo
Alcatel
Alcatel
Alcatel
Corning

Corning
Glass Type
12-fiber stranded
24-fiber stranded
36-fiber stranded
48-fiber stranded
72-fiber stranded
96-fiber stranded
IFC Type Multimode (Indoor)
AM
BM
DM
2M
VM
WM
Corning
Corning
Corning
Corning
Corning
Corning
Glass Type
72-position
96-position
144-position (LX.5
®
only)
144-position (OMX 800 only)
A
B

C
D
Block Configuration
0
Ultra PCSC
Angled SC 8°
Ultra PCFC
Angled FC 8°
Ultra PCST
Angled E-2000 8°
LX.5
®
Ultra PCSC, zirconia sleeve
Ultra PCFC, zirconia sleeve
7
L
2
Q
4
V
X
8
3
Adapter/Connector #1 Singlemode
No connector/stub end
SC
FC
ST
LX.5
®

0
9
A
5
Y
Connector #2
Multimode (62.5/125)
®
No connector/stub end
Ultra PCSC
Angled SC 8°
Ultra PCFC
Angled FC 8°
Ultra PCST
Angled E-2000 8°
LX.5
®
Ultra PCSC, zirconia sleeve
Ultra PCFC, zirconia sleeve
0
7
L
2
Q
4
V
X
8
3
Connector #2 Singlemode

Length in Meters
SC
FC
ST
LX.5
®
9
A
5
Y
Adapter/Connector #1
Multimode (62.5/125)
®
Block Orientation
Left
Right
L
R
OR
OR
Contact your ADC representitve for termination
modules with outside plant cable.
Catalog Number
10/03 • 100571
600 mm Products
23
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
23
OMX
™

Optical Distribution Frame
Value-Added Module System Chassis
The OMX VAM chassis is designed to fit into any
open chassis location within new or existing OMX
600 optical distribution frames. Each chassis can
accommodate a maximum of ten VAM plug-in
modules, ten bulkhead plates, ten blank plates or
any combination thereof.
Description
Unloaded chassis - left orientation;
accommodates up to 10 modules
Unloaded chassis - right orientation;
accommodates up to 10 modules
Catalog Number
MX6-VAMCHAS-L
MX6-VAMCHAS-R
Dimensions (HxWxD)
14.69" x 8.93" x 11.25"
(37.31 x 22.68 x 28.58 cm)
14.69" x 8.93" x 11.25"
(37.31 x 22.68 x 28.58 cm)
Ordering Information
Left Chassis
Right Chassis
Ordering information for value-added modules starts on page 54.
10/03 • 100571
600 mm Products
24
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Splice Module

The OMX splice module provides mounting positions
and protection for 24 splice trays. The splice module
is the height of two termination modules. The
module may be ordered with a ”left“ orientation
(mounts on the left side of the frame) or a ”right“
orientation (mounts on the right side of the frame).
Splice modules must be mounted to the frame
starting in the bottom position.
OMX
™
Optical Distribution Frame
Splice Module and Splice Tray
Catalog Number
MX6-24SPNL-R
MX6-24SPNL-L
Ordering Information
Description
OMX (24) tray splice module
Height = 2 module positions
Right orientation
Left orientation
Splice Tray
The round splice tray used in the OMX simplifies
installation and maintenance. The tray stores up to
three meters of slack allowing the installer to roll
the tray away from the frame to perform splicing.
Catalog Number
FST-DRS ___ ___ - ___ ___
00
FT

HS
MT
URCM
NT
ANT
RT
3M
Empty
Bare fusion
Heat shrink fusion
Mechanical (elastomeric)
Universal Raychem
Nortel QPAK
Swiss ANT
Rotary
FibrLok
®
Splice Type
Number of Splices
1
For 8 fiber ribbon only
12
16
24
32
1
10/03 • 100571
600 mm Products
25
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42

OMX
™
Optical Distribution Frame
Frame Accessories
OMX Jumper Storage Module
The OMX jumper slack storage module provides for jumper
storage functionality within the frame. Up to five jumper
storage modules can be mounted on one side of an OMX
frame. Jumper storage modules must be mounted to the
frame starting in the bottom position.
OMX Interbay Management Panel
The OMX interbay management panel provides slack storage between frames for interconnect or
cross-connect jumpers. The Interbay Management Panel is necessary when no jumper storage
is provided on the OMX frame itself.
Catalog Number
MX6-JSM00000
MX6-JSM80000
Ordering Information
Description
OMX 600 jumper storage module (OMX 600 only)
OMX 800 jumper storage module (OMX 800 only)
Catalog Number
MX6-IMP150
MX6-IMP200
Dimensions (HxWxD)
2200 x 150 x 300 mm
2200 x 200 x 300 mm
Ordering Information
Description
150 mm OMX interbay management panel

200 mm OMX interbay management panel
Catalog Number
MX6-ENDGRD
Dimensions
2200 x 300 mm
Ordering Information
Description
OMX end guard
OMX End Guard
The OMX end guard provides protection for the fibers entering and exiting frames at the ends of a lineup.
The end guard attaches directly to the interbay management panel, but does not add to the overall frame
width. End guards are not required when ordering splice bays or bays without external interbay
management panels. The OMX end guard can be mounted to both the OMX 600 and OMX 800.
10/03 • 100571
600 mm Products
26
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
OMX
™
Optical Distribution Frame
Frame Accessories
OMX Outside Plant Cable Clamp
The OMX cable clamp is used to secure the OSP/IFC cable to the base or top of the frame.
Catalog Number
OSP-CLPFEC-LG
MX6-ACC001
Ordering Information
Description
OMX outside plant cable clamp for top entry cables; clamps up to 3 cables
OMX outside plant cable clamp for underfloor cable entry

Rack Installation Kits
Catalog Number
RAC-MX0616
RAC-MX0615
Ordering Information
Description
Rack installation kit for concrete floor, kit includes:
(2) M8 bolts, 90 mm
(4) M8 nuts
(8) flat washers
(4) lock washers
shims and anchor plates
Rack installation kit for raised floor, kit includes:
(4) threaded rods M12 x 1 m
(12) heavy nuts, lock and flat washers
(4) nuts with springs, M12
(2) 1.8 m unistrut
(1) anchor kit