901 k0040 V4(中英文)SMT送板機作業規範SMT board loader operating specification
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (1.62 MB, 8 trang )
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 1 OF 8
Revision History
Rev.
Status
Revision Date
Revised By
1
2007/7/9
文文
2
2016/3/6
文文文
3
2019/3/4
文文文
4
2019/8/19
文文文
Description
文文文文
1. 文文文文: 文文文文文文文文文文 Form No文901-K0040-02
2. 文文文文: 文文文文文文文文文文文文文
Form No文902-N19-29
3. “6.2 文文文文文文文文文”文“6.3 文文文文文文文文文”文文文文文文文文
文文文文文文文文文文文文文文文文
For V1 factory build-up requirement, add English
translation.
文文文文文文
Add Vietnamese translation
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 2 OF 8
目目 CONTENTS
1.0 文文
PURPOSE..................................................................................................................................................3
2.0 文文
SCOPE.......................................................................................................................................................3
3.0 文文
DEFINITIONS...........................................................................................................................................3
4.0 文文
RESPONSIBILITIES.................................................................................................................................3
5.0 文文文文
FLOWCHART...........................................................................................................................................3
6.0 文文文文
ACTIVITIES DESCRIPTION...................................................................................................................4
7.0 文文文文
REFERENCES...........................................................................................................................................7
8.0 文文
ATTACHMENTS.......................................................................................................................................7
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 3 OF 8
1.0 文文
PURPOSE
文文 SMT OPERATOR 文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
To ensure that the SMT operators are able to operate the equipment correctly and to avoid equipment
damage and industrial safety accidents due to improper operation and also to effectively make the best
of equipment throughput for the accomplishment of the production goal.
2.0 文文
SCOPE
2.1 NQJ/NQX/V1 SMT 文文 OP 文文文文文文文文文文
All SMT operators and engineering technicians at NQJ/NQX/V1;
2.2 文文文文文 SMT 文文文文文文文文文文文文文文文文文
This manual is applicable to equipment operation of board loaders during SMT production and
manufacturing.
3.0 文文
DEFINITIONS
文
None
4.0 文文
RESPONSIBILITIES
4.1 文文文文文文文文文文文文文文文文
Production Unit: Is responsible for operating and daily maintenance of equipment.
4.2 文文文文文文文文文文文文文文文文文文文文文文文文文
Engineering Unit: Is responsible for troubleshooting, daily care, and educational training for
operators.
5.0 文文文文
FLOWCHART
文
None
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 4 OF 8
6.0 文文文文
ACTIVITIES DESCRIPTION
6.1 文文文文文
Preparation Prior to Start-up
6.1.1
文文文文文文文 4-6Kg/CM 文文文文文
Check if the air pressure is 4-6 Kg/CM.
6.1.2
文文文文文文文文文
Select the emergency stop button.
6.2 文文文文文文文文文
Cheng Tai Board Loader Operating Steps
6.2.1
文文文文
Startup Steps
6.2.1.1
文文文文文文文文文文文文文
Turn on main power and the machine will start automatically.
6.2.1.2
文文文文文文文文文文文文文文文文文文文
Under the manual mode, place in the material frame and pay attention to the orientation of
the material frame;
6.2.1.3
文“文文文文”文文文文文文文文文文文文
Press “Lower Basket in” so that the material frame is sent into the board loader;
6.2.1.4
文文文文文文文文文“文文”文文文文文文文文文文文文文文文文
Shift to the Auto page and click on “Start”; the material frame will automatically elevate to
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 5 OF 8
the first board pushing position.
6.2.2
文文文文
Shut-down Steps
6.2.2.1
文文“文文”文文文文文文文文文
Press “Stop” to stop the machine;
6.2.2.2
文文文文文文文文文文文文文
Press the power switch to shut down main power.
文文文文
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 6 OF 8
6.3 文文文文文文文文文
Sheng Ta Board Loader Operating Steps
6.3.1
文文文文
Start-up Steps
6.3.1.1
文文文文文文
Turn on main power;
6.3.1.2
文文文文文文文文文文文
Press the power button for the operator interface;
6.3.1.3
文文文文文文文文文文文文文文文文文文文
Under the manual mode, place in the material frame and pay attention to the orientation of
the material frame;
6.3.1.4
文文“文文”文文文文文文文文文文文文
Press “Move in” so that the material frame is sent into the board loader;
6.3.1.5
文文文文文文文文文文文文文文文文文文文文文
Shift to the Auto mode; the material frame will automatically elevate to the first board
pushing position.
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 7 OF 8
6.3.2
文文文文
Shut-down Steps
6.3.2.1
文文文文文文文文文文文
Press the power button for the operator interface.
6.3.2.2
文文文文文
Shut down main power
6.4 文文文文
PRECAUTIONS
6.4.1
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
If the equipment experiences abnormality, the operator shall notify the technician, the engineer,
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
Document Content
□文文文文 Addition of Document
■文文文文 Alteration of Document
□文文文文 Revocation of Document
Subject: SMT 文文文文文文文
Doc. No.: 901-K0040
REV: 4
SMT Board Loader Operating Specification
PAGE 8 OF 8
or the direct supervisor immediately to handle the issue.
6.4.2 文文文文文文文901-K0040-01 文文文文文文文文文文文文文文文文文
The production unit performs daily maintenance according to the 901-K0040-01 (BOARD
LOADER CLASS 1 MAINTENANCE RECORD SHEET.)
6.4.3 文文文文文文文902-N19-29 文文文文文文文文文文文文文文文文文文文文
The engineering unit performs monthly maintenance according to the 902-N19-29 (board
loader class 2 preventive maintenance inspection form).
7.0 文文文文
REFERENCES
文
N/A
8.0 文文
ATTACHMENTS
8.1 901-K0040-01 文文文文文文文文文文
901-K0040-01 (board loader class 1 maintenance record sheet)
8.2 902-N19-29 文文文文文文文文文文文文文
902-N19-29 (board loader class 2 preventive maintenance inspection form)
文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文文
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission from WNC.
Form No.: 2-JQ-021-04, 006
