H 4016 8200 01 a renishaw GUI for okuma machine tools low res

Renishaw GUI for Okuma machine tools

Working in conjunction with Okuma, Renishaw has developed a range of graphical user interface (GUI) software applications.
These applications – Renishaw GUIs for Okuma machine tools – provide an intuitive, user-friendly programming environment
that guides users through the process of generating machine code. Eliminating the difficulty associated with traditional machine
tool programming techniques, use of the GUI allows cycles to be produced and selected with minimal user input.

Key features and benefits
• Provides an intuitive, easy-to-use programming interface
• Simplifies calibration and operation of Renishaw machine tool probing systems
• Compatible with P200M/P300M and P200/P300L controls
• Integrated using Okuma’s THINC API
The Renishaw GUI guides users through various probing, tool setting and machine health check cycles.

Feature inspection

Contact tool setting

Non-contact tool setting

AxiSet™ Check-Up


Renishaw Inc
5277 Trillium Blvd
Hoffman Estates IL 60192
United States

T +1 847 286 9953
F +1 847 286 9974
E

www.renishaw.com

Renishaw GUI for Okuma machining centres
Provides on-screen selection buttons allowing machine-resident Renishaw inspection and tool
setting cycles to be called.



Renishaw GUI for Okuma lathes and multi-tasking machines
Provides on-screen selection buttons allowing machine-resident Renishaw inspection and
AxiSet Check-Up pivot point compensation cycles to be called.

Cycles*
Type

Functionality

Renishaw GUI for Okuma machining centres
Inspection

Cycles: bore, boss, pocket, web, single surface.
Calibration: diameter, length.

Contact tool setting

Cycles: manual length, automatic length, automatic length and diameter.
Calibration: round stylus, square stylus.

Non-contact tool
setting

Cycles: length, length and diameter.
Calibration: beam alignment, beam calibration.

Renishaw GUI for Okuma lathes and multi-tasking machines
Inspection

Cycles: bore, boss, pocket, web, single surface, sphere.
Calibration: bore, boss, pocket, web, single surface, sphere, length, slot.

AxiSet Check-Up

Identifies poor machine alignment, geometry and pivot point errors.

* The relevant software packages MUST be installed and configured according to their installation documentation before using
the Renishaw GUI.

Part numbers and compatibility
Part Number

Compatibility

Renishaw GUI for Okuma machining centres
A-4016-1063

Okuma P200 and P300M controls and API version 1.9.1.0 or later.
API version 1.16.0.0 is recommended (1.12.1.0 minimum) for P300M controls when running tool setting
cycles: earlier versions of the API will not load tool data.

Renishaw GUI for Okuma lathes and multi-tasking machines

A-4016-1075

Okuma P200 and P300L controls and API version 1.12.1.0 or later.

Please quote relevant part number(s) when ordering.

General requirements
Ensure that the API and THINC Startup Service are installed. These applications are included with all P200 and P300 controls.
THINC Startup Service is required to ensure that the machine’s NC is fully booted before the GUI is run.
If an API icon is not displayed at the bottom of the controller screen, contact your local Okuma distributor and arrange for the API
to be installed.


For worldwide contact details, visit www.renishaw.com/contact
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT AT THE DATE OF PUBLICATION BUT
MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT. RENISHAW EXCLUDES LIABILITY, HOWSOEVER ARISING, FOR ANY
INACCURACIES IN THIS DOCUMENT.
© 2015 Renishaw plc. All rights reserved.
Renishaw reserves the right to change specifications without notice.
RENISHAW and the probe symbol used in the RENISHAW logo are registered trade marks of Renishaw plc in the United Kingdom and other countries.
apply innovation and names and designations of other Renishaw products and technologies are trade marks of Renishaw plc or its subsidiaries.
All other brand names and product names used in this document are trade names, trade marks or registered trade marks of their respective owners.

*H-4016-8200-01*

Issued: 03.2015 Part no. H-4016-8200-01-A