Mô hình tháp Eiffel, Pháp. P1

Eiffel Tower (Night and Day; France): Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc.
© PAOPAO. Inc

Before starting assembly:Writing the number of each section on its back side
before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)

Indicates where sections
should be glued together.

/>* In addition to the combined day-night model,
you can also build separate day and night Eiffel Tower models.
[1] Assemble the tower structure (the base below the pillars).
Attach the rear surface parts after first attaching the side surface parts into place.

View of completed model
*This model was designed for Papercraft and may differ from the original in some respects.

Assembly Instructions: Six A4 sheets (No.1 to No.6)
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.

*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.

Attach these pieces
in the same way as
on the opposite side.

Assembly Instructions
Mountain fold(dotted line)

Make a mountain fold.
Valley fold(dashed and dotted line)

Make a valley fold.
Scissors line(solid line)

Cut along the line.
Cut in line(solid line)

Cut along the line.

Tools and materials

Glue
The glue spot(colored dot)
shows where to apply the glue.

Attach parts 4 and 6
(35 and 37) into place after
first attaching part 2 (33).

Glue spot(Red dot)

Glue parts with the same number together.
Glue spot(Green dot)

Glue within the same part.

Glue spot(Blue dot)

Glue to the rear of the other part.

Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Attach parts 8 and 10 (39 and 41) last.
Assembly tip
Caution

Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.

* Assemble the tower (night) parts in the same way.
Tower (night) part numbers are indicated in parentheses above.


Eiffel Tower (Night and Day; France): Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc.
© PAOPAO. Inc

[2] Assemble the structure by putting the parts together in numbered order, aligning the printed symbols appearing on the parts.
* Assemble these parts so that the structure is flush with the background.
Attach part 16 (47) into position on
the white area of part 15 (46).
Attach part 15 (46) into position along

the white line on part 14 (45).
Attach part 14 (45) into position along
the white line on top of part 13 (44).

Attach the base, then fold
in the side flaps.

Attach the pillars into place
so that they align with the
white symbols printed on top
of part 14 (45).

Attach the bottom
in the same way.

Left side

Right side

* Assemble the tower (night) parts in the same way.
Tower (night) part numbers are indicated in parentheses above.


Eiffel Tower (Night and Day; France): Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc.
© PAOPAO. Inc

[3] Assemble the structure.
* Assemble these parts so that the structure is flush with the background.

Attach the sides in the same way.

Fold and insert inside
the structure, then attach
to the bottom part.

Attach to the bottom inside
assembled part 12 (43).

Attach in the same way as the top.

* Assemble the tower (night) parts in the same way.
Tower (night) part numbers are indicated in
parentheses above.


Eiffel Tower (Night and Day; France): Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc.
© PAOPAO. Inc

[4] Assemble the base.

©
/ on
/en Can

AO
OP
PA

c
. In

.
Inc

ark of
/c-p ark
om dem
n.c tra
no red
.ca iste
ww reg
://w is a
p
htt n ®
no

Ca

Eiffel Tower

Before attaching the parts, draw lines
crossing perpendicularly at the center
on the reverse side of part 63.

Paris, France

Turn the base upside down and

attach part 66 to align with the lines
you drew in the previous step.
After attaching part 66,
turn the base right-side up again.

©
/ on
/en an
ark f C
-p ark o
m/c em
.co ad

n tr
no red
.ca iste
ww reg
/w a
p:/ is
htt on ®
Ca

Eiffel Tower
Paris, France

View from below

n

.

Inc

. In
AO
OP
PA

c


Eiffel Tower (Night and Day; France): Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc.
© PAOPAO. Inc

[5] Assemble the background screen.

Attach the night background screen in the same way.

and

Apply glue to the entire region
within approximately 40 mm from
the fold lines on both ends,
then attach the two parts.

Glue

© PA
c.

/ n In
k/en Cano
-par k of
m/c mar
n.co de
no red tra

ca te
ww. regis
://w is a
http n ®
no
Ca

Eiffel Tower
Paris, France

AO
OP

. In

c

Place the background screen in the
center of part 75, with day parts 83
and 84 facing the brighter side of
part 75 and the night parts 85
and 86 facing the darker side.

Glue the tabs to the underside
of part 75.


Eiffel Tower (Night and Day; France): Assembly Instructions
[6] Assemble the background trees.

Canon ® is a registered trademark of Canon Inc. © Canon Inc.
© PAOPAO. Inc

[7] Final assembly of the model

* To make gluing easier, bend these
to curve them before gluing them into place.

* Glue the Eiffel Tower into place in the center
in a manner you feel is visually balanced.

As the final step,
fold inward and
glue into place.
As the final step,
insert this tab into the interior.

on the opposite side

©

Position these (five) trees in a visually
balanced manner.

Assemble the night parts on the opposite
side from the day parts, in the same way.

n/ n
/e Ca
ark of
-p rk
/c ma
om d e
.c tra
on d
an tere
is
w.c g
w a re
/w

p:/ ®
htt on

on

In

PA
O
PA

O

c
. In

c.

is

n
Ca

Eiffel Tower
Paris, France

* Night part numbers are indicated
in the parentheses above.

Finished!

Glue into place to
align the curves.