KỸ THUẬT NÂNG - VẬN CHUYỂN
CHƯƠNG 3
DÂY & CÁC CHI TIẾT QUẤN,
HƯỚNG DÂY
(WIRE ROBES AND CHAINS FOR
HOISTING AND HAULAGE. LIFTING
TACKLE, DRUM, SHEAVES, SPROCKETS)
Chapter III
1
1. DÂY CÁP THÉP
(wire rope)
Cấu tạo:
-Chế tạo từ những sợi thép
sáng hay tráng kẽm đường kính
từ 0,2-3mm đã được hóa cứng
Chapter III
2
1. DÂY CÁP THÉP (tt)
(wire rope)
Kết cấu
Tùy theo cách bện:
-Bện đơn
-Bện kép
-Bện ba lớp
Tùy theo chiều cuốn :
-Bện xuôi
- bện chéo
- Bện tổng hợp
Chapter III
Tùy theo tình trạng tíêp xúc :
-Tiếp xúc đường
-Tiếp xúc điểm
3
1. DAY CAP THEP (tt)
(wire rope)
Beọn keựp
Chapter III
4
1. DAÂY CAÙP THEÙP (tt)
(wire rope)
Chapter III
5
1. DÂY CÁP THÉP (tt)
(wire rope)
Cấu tạo theo chiều cuốn
LLL %20rope
RLL %20rope
LRL %20rope
Chapter III
RRL %20rope
6
1. DÂY CÁP THÉP (tt)
(wire rope)
Tính và chọn dây
1. Individual wires, the ropes – an object of intricate constructionis composed of, are subject to various stresses in service
(contact, tension, bending, and twisting)
2. A mathematical treatment of all the factors controlling the
wires of rope is practical impossible
3. Codes used in rope design are based on factors of maximum
rope tension, and safety
4. Ropes are selected from applicable standards, using the
relationship
S = n.Smax ≤ S
d
d
Chapter III
7
1. DÂY CÁP THÉP (tt)
(wire rope)
Sử dụng cáp
-Cáp thường không đứt tức thời.
-Chỉ lọai bỏ cáp khi số sợi đứt cáp trên một bước dài vượt
số sợi cho phép
Hệ số
Kết cấu cáp
an
6 x 19 = 114 sợi 6 x 37 = 222 sợi
toàn
Bện
Bện
Bện
Bện
xuôi
chéo
xuôi
chéo
≤6
6
12
11
22
6
7
14
13
26
7
8
Chapter III
15
30
16
8
1. DÂY CÁP THÉP (tt)
(wire rope)
Nối đầu dây với chi tiết khác
(Attachment of ropes to machinery parts)
Chapter III
9
1. DÂY CÁP THÉP (tt)
(wire rope)
•Sử dụng đúng cáp
Chapter III
10
1. DAÂY CAÙP THEÙP (tt)
(wire rope)
Chapter III
11
1. DAÂY CAÙP THEÙP (tt)
(wire rope)
Chapter III
12
1. DAÂY CAÙP THEÙP (tt)
(wire rope)
Chapter III
13
1. DAÂY CAÙP THEÙP (tt)
(wire rope)
Chapter III
14
1. DAÂY CAÙP THEÙP (tt)
(wire rope)
Chapter III
15
1. DÂY CÁP THÉP (tt)
(wire rope)
Phương pháp cố đònh đầu cáp trên tang
Chapter III
16
2. XÍCH (chains)
Xích haøn (welded)
-These are widely used in hoisting
installation as pliable members
-Welded chains fall in to ordinary
type and calibrated one differing
by the accuracy of fabrication
Xích baûn leà ( roller chains)
-Roller chains consist of steel plates hinge- joined by pins
-Normally the chains are tested by the manufacturer with a load
equal to half the breaking one
-Roller chains are ore reliable than welded
- Roller chains are heavier and more costly then welded ones
Chapter III
17
3. TANG CUỐN CÁP (drums)
Mục đích:
Phân loại:
Tang trụ.
Tang côn.
Tang ma sát.
Cấu tạo, chế tạo:
Một lớp, nhiều lớp.
Có rãnh, không có rãnh.
Đúc hàn.
Chapter III
18
3. TANG CUỐN CÁP( tt) :
1. Tang trụ.
-Distinction is made between drums spooling
the rope in one layer and those on which
the rope is wound is more than one layer
- The winding face of drum is made smooth
or provided machined helical grooves
Các thông số cơ bản : L,t, D
Chapter III
19
3. TANG CUOÁN CAÙP( tt) :
Chapter III
20
3.TANG CUOÁN CAÙP (drums) tt
D≥ (e-1)dc
L=L0+L1+2L2
L0=Z.t ={l/π(D+dc)}t +(1,5-2)t
L0=Z.t ={a.H/π(D+dc)}t +(1,5-2)t
t=dc+(2-3)mm
Chapter III
21
3.TANG CUỐN CÁP (drums) tt
Chiều dầy tang
-Tang bằng gang:
-Tang bằng thép:
δ=0,02D+(6-10) mm
δ=1,2dc
Tính bền tang
-L/D<3: kiểm tra nén: σn=k.Smax/δ.t≤[σn]
- L/D≥3:kiểm tra uốn, xoắn: σu=Mu/Wu
τx=Mx/Wx
-Tổng ứng suất:
σ = ( σ n + σ u )2 + 3τ x2
Chapter III
22
3.TANG CUỐN CÁP (drums) tt
Tang côn
Mục đích:
Phạm vi sử dụng.
Dmax ⋅ S min = Dmin ⋅ S max
Chapter III
23
3. TANG CUOÁN CAÙP( tt) :
Chapter III
24
3. TANG CUỐN CÁP( tt) :
3. Tang và puly ma sát.
Capstan drums (traction –type drum)
Mục đích.
Phạm vi sử dụng.
The rope connected to the
load is not fastened to the drum
but is held fast to it owing to
traction between the drum
surface and a few turn of rope
coiled around the drum
Chapter III
Hence according to Euler,
the tension in the entering
side of rope connected to
the load is given:
fα
Se=Sle25