BÀI tập assembly của phần mềm solidworks

Bench Vice Assembly

1

Bench Vice Assembly
In this project, you will create the Bench Vice assembly. Figures B through E shows the views
and dimensions of the components of the Bench Vice assembly.

Figure 1 The Bench Vice assembly

Figure 2 Views and dimensions of the base


2

Student Project

Figure 3 Views and dimensions of the Vice Jaw

Figure 4 Views and dimensions of various components of the Bench Vice assembly


Bench Vice Assembly

Figures 5 Views and dimensions of various components of the Bench Vice assembly

3


Butterfly Valve Assembly

1

Butterfly Valve Assembly
Create the components of the Butterfly Valve assembly and then assemble them, as shown in
Figure 1. The dimensions of the components are shown in Figures 2 through 7. Assume the
missing dimensions.

Figure 1 The Butterfly Valve assembly

Figure 2 Dimensions of the Body


2

Student Project

Figure 3 Dimensions of the Shaft

Figure 5 Top view of the Arm

Figure 4 Dimensions of the Retainer

Figure 6 Sectional front view of the Arm

Figure 7 Dimensions of the Plate, Nut, and Screw


Double Bearing Assembly

1

Double Bearing Assembly
In this project, you will create the Double Bearing assembly shown in Figure 1. The exploded
state of the assembly is shown in Figure 2 and the dimensions of the components of the
Double Bearing assembly are shown in Figures 3 through 7.

Figure 1 The completed Double Bearing
assembly

Figure 2 The exploded view of the Double
Bearing assembly

Figure 3 Top view of the Base

Figure 4 Top view of the Cap

Figure 5 Front view of the Base

Figure 6 Front view of the Cap


2

Student Project

Figure 7 Dimensions and drawing views of the Bushing and the Bolt


Fixture Assembly

1

Fixture Assembly
Create all the components of the Fixture assembly and then assemble them, as shown in
Figure 1. The details of the components of the Fixture assembly are shown in
Figures 2 through 5.

Figure 1 The Fixture assembly

Figure 2 Dimensions of the End Plate


2

Student Project

Figure 3 Dimensions of the Disk

Figure 4 Dimensions of the Support Pin and the Bolt


Fixture Assembly

3

Figure 5 Dimensions of the Spacer, Center Pin, and the Nut


Motor Blower Assembly

1

Motor Blower Assembly
In this project, you will create the Motor Blower assembly shown in Figure 1. The exploded
view of the assembly is shown in Figure 2. The details of the components of the Motor Blower
assembly are shown in Figures 3 through 8.

Figure 1 Motor Blower assembly

Figure 2 Exploded view of the Motor Blower assembly


2

Student Project

Figure 3 Dimensions of the Upper Housing

Figure 4 Dimensions of the Lower Housing


Motor Blower Assembly

3

Figure 5 Dimensions of the Blower

Figure 6 Dimensions of the Motor

4

Student Project

Figure 7 Dimensions of the Cover

Figure 8 Dimensions of the Shaft


Pipe Vice Assembly

1

Pipe Vice Assembly
In this Project, you will create all components of the Pipe Vice assembly, as shown in
Figure 1, and then assemble them. The dimensions of the components are given in
Figures 2 and 3.

Figure 1 The Pipe Vice assembly

Figure 2 Views and dimensions of the Base


2

Student Project

Figure 3 Views and dimensions of the Screw, Handle, Movable Jaw, and Handle Screw

Plummer Block Assembly

1

Plummer Block Assembly
In this project, you will create the components of the Plummer Block assembly, as shown in
Figure 1 and then assemble them. The dimensions of the components are given in Figures 2
through 4.

Figure 1 The Plummer Block assembly

Figure 2 Views and dimensions of the Casting


2

Student Project

Figure 3 Views and dimensions of the Cap

Figure 4 Views and dimensions of Brasses, Nut, Lock Nut, and Bolt


Pulley Support Assembly

1

Pulley Support Assembly
Create the components of the Pulley Support assembly and then assemble them, as shown in
Figure 1. After creating the assembly, create its exploded view, as shown in Figure 2. The

dimensions of the components are given in Figures 4 through 8.

Figure 1 The Pulley Support assembly

Figure 2 Exploded view of the Pulley Support assembly


2

Student Project

Figure 4 Dimensions of the Pulley

Figure 5 Dimensions of the Bushing

Figure 6 Left-side view of the Bracket

Figure 7 Sectioned front view of the

Figure 8 Dimensions of the Washer, Cap Screw, Turn Screw, and Nut


Pulley Support Assembly

Figure 3 Parts list for the Pulley Support assembly

3


Radial Engine Assembly

1

Radial Engine Assembly
In this project, you will create the Radial Engine assembly shown in Figures 1 and 2. The
Radial Engine assembly will be created in two parts, one will be the subassembly and the
other will be the main assembly. The dimensions of the components of the Radial Engine
assembly are shown in Figures 3 through 6.

Figure 1 The Radial Engine assembly

Figure 2 The exploded view of the assembly

Figure 3 Views and dimensions of the Piston


2

Student Project

Figure 4 Views and dimensions of the Articulated Rod

Figure 5 Views and dimensions of the Master Rod


Radial Engine Assembly

Figure 6 Views and dimensions of the Rod Bush Upper, Rod Bush Lower, Piston Pin Plug,
Piston Pin, Piston Rings, and Master Rod Bearing

3


Shaper Tool Head Assembly

1

Shaper Tool Head Assembly
Create the Shaper Tool Head assembly, as shown in Figure 1. After creating the assembly, create
its exploded view, as shown in Figure 2. The dimensions of the components are given in
Figures 3 through 7.

Figure 1 The Shaper Tool Head assembly

Figure 2 The exploded view of the Shaper Tool
Head assembly