Tài liệu xe HONDA ACCORD - P5

ＴＡ０８Ｅ０００００００００Ｊ２００１ＡＢＡＴ００
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) (If body maintenance is required)
The Accord SRS includes a driver’s airbag in the steering wheel hub, a passenger’s airbag in the dashboard above the
glove box, seat belt tensioners in the front seat belt retractors, seat belt outer lap tensioners in the front seat belt lower
anchor, side curtain airbags in the sides of the roof, and side airbags in the front seat-backs. Information necessary to
safely service the SRS is included in this Shop Manual. Items marked with an asterisk ( ) on the contents page
include or are located near SRS components. Servicing, disassembling, or replacing these items requires special
precautions and tools, and should be done by an authorized Honda dealer.
• To avoid rendering the SRS inoperative, which could lead to personal injury or death in the event of a severe frontal
or side collision, all SRS service work should be done by an authorized Honda dealer.
• Improper service procedures, including incorrect removal and installation of the SRS, could lead to personal injury
caused by unintentional deployment of the airbags, side airbags, and/or side curtain airbags.
• Do not bump or impact the SRS unit, front impact sensors, or side impact sensors, or rear safing sensor when the
ignition switch is ON (II), or for at least 3 minutes after the ignition switch is turned to LOCK (0); otherwise, the
system may fail in a collision, or the airbags may deploy.
• SRS electrical connectors are identified by yellow color coding. Related components are located in the steering
column, front console, dashboard, dashboard lower panel, in the dashboard above the glove box, in the front seats,
in the roof side, and around the floor. Do not use electrical test equipment on these circuits.
07/09/20 19:31:50 62TA000B_200_0001
ＴＡ０８Ｅ０００００００００Ｊ２００１ＺＣＡＴ００
Body
Doors
Mirrors
Glass
Sunroof
Interior Trim
Consoles
Dashboard
............................................................................................Special Tools . 20-2
......................
....

...
................
...........................................
...........................................
...........................................
...........................................
...........................................
...
.....
....
..................
...........................................
...........................................
...........................................
...........................................
..
.....
.............................
........................
...........................
......................
....
...
................
...........................................
...........................................
...........................................
...........................................
...........................................
...

.....
....
..................
...........................................
...........................................
...........................................
...........................................
..
.....
.............................
........................
...........................
Component Location Index . 20-3
Front Door Panel Removal/Installation . 20-12
Front Door Outer Handle Replacement . 20-19
Front Door Latch Replacement . 20-23
Front Door Glass and Regulator
Replacement . 20-26
Front Door Sash Inner Trim
Replacement . 20-29
Front Door Sash Outer Trim
Replacement . 20-31
Front Door Glass Outer Weatherstrip
Replacement . 20-31
Front Door Outer Molding
Replacement . 20-33
Front Door Weatherstrip Replacement . 20-34
Rear Door Panel Removal/Installation . 20-35
Rear Door Outer Handle Replacement . 20-38
Rear Door Latch Replacement . 20-40

Rear Door Glass and Regulator
Replacement . 20-42
Rear Door Sash Inner Trim
Replacement . 20-45
Rear Door Sash Outer Trim
Replacement . 20-46
Rear Door Glass Outer Weatherstrip
Replacement . 20-47
Rear Door Outer Molding Replacement . 20-48
Rear Door Weatherstrip Replacement . 20-49
Door Glass Adjustment . 20-50
Door Position Adjustment . 20-51
Door Striker Adjustment . 20-53
......................
......................
......................
........
.................
......................
......................
......................
........
.................
Component Location Index . 20-54
Power Mirror Replacement . 20-56
Mirror Holder Replacement . 20-57
Mirror Housing Cover Replacement . 20-59
Rearview Mirror Replacement . 20-59
......................
..........................

...........................................
....
......................
......................
......................
..........................
...........................................
....
......................
......................
Component Location Index . 20-61
Windshield Replacement . 20-63
Rearview Mirror Harness Cover Base
Replacement . 20-68
Rain Sensor Cover Base Replacement . 20-69
Rear Window Replacement . 20-70
Quarter Glass Replacement . 20-79
......................
............
.......................
....................................
............
....................
.....................
............................
...................................
.......
...........................................
..
......................

............
.......................
....................................
............
....................
.....................
............................
...................................
.......
...........................................
..
Component Location Index . 20-84
Symptom Troubleshooting Index . 20-85
Glass Position Adjustment . 20-86
Glass Replacement . 20-86
Glass Weatherstrip Replacement . 20-87
Wind Deflector Replacement . 20-88
Drain Channel Replacement . 20-89
Sunshade Replacement . 20-90
Motor Replacement . 20-91
Frame and Drain Tube Replacement . 20-91
Drain Channel Slider and Cable Assembly
Replacement . 20-94
Closing Force and Opening Drag Check . 20-96
......................
..
.............
..................
.....................................
....................................

..
.....
.................
...........
................
..................................
......................
..
.............
..................
.....................................
....................................
..
.....
.................
...........
................
..................................
Component Location Index . 20-98
Trim Removal/Installation - Door Areas . 20-101
Trim Removal/Installation - Pillar Areas
- Without Side Curtain Airbags . 20-105
Trim Removal/Installation - Pillar Areas
- With Side Curtain Airbags . 20-108
Trim Removal/Installation
- Rear Side Area . 20-124
Trim Removal/Installation
- Rear Shelf Area . 20-125
Trim Removal/Installation - Trunk Area . 20-128
Trim Removal/Installation - Trunk Lid . 20-128

Sunvisor Removal/Installation . 20-134
Grab Handle Removal/Installation . 20-136
Headliner Removal/Installation . 20-138
Carpet Replacement . 20-150
..............................
......
..............................
................
..............................
..............................
......
..............................
................
..............................
Center Console Panel
Removal/Installation . 20-156
Center Console Removal/Installation . 20-158
Center Console Rear Trim
Removal/Installation . 20-160
Console Armrest Replacement . 20-161
Accessory Power Socket Trim
Removal/Installation . 20-164
....
..............................
.......
..............................
..............................
..............................
.........
..............................

..............................
..............................
...
...............
...............
..............................
..............................
..............................
..............................
..............................
..............................
........
..............................
.....................
....
..............................
.......
..............................
..............................
..............................
.........
..............................
..............................
..............................
...
...............
...............
..............................
..............................
..............................

..............................
..............................
..............................
........
..............................
.....................
Instrument Visor Removal/Installation . 20-165
Driver’s Dashboard Lower Cover
Removal/Installation . 20-166
Driver’s Pocket Removal/Installation . 20-167
Driver’s Dashboard Undercover
Removal/Installation . 20-168
Driver’s Outer Dashboard Trim
Removal/Installation . 20-168
Driver’s Inner Dashboard Trim
Removal/Installation . 20-169
Center Pocket Removal/Installation . 20-169
Dashboard Center Lower Cover
Removal/Installation . 20-170
Center Display Visor
Removal/Installation . 20-172
Passenger’s Dashboard Trim
Removal/Installation . 20-172
Glove Box Lock Cylinder Replacement . 20-173
Glove Box Removal/Installation . 20-174
Glove Box Striker Replacement . 20-176
Passenger’s Dashboard Undercover
Removal/Installation . 20-176
Dashboard Side Vent
Removal/Installation . 20-177

Side Defogger Vent Trim
Removal/Installation . 20-178
Driver’s Outer Middle Pad
Removal/Installation . 20-178
Driver’s Inner Middle Pad
Removal/Installation . 20-179
Passenger’s Middle Pad
Removal/Installation . 20-179
Column Cover Removal/Installation . 20-180
Dashboard/Steering Hanger Beam
Removal/Installation . 20-182
Dashboard/Steering Hanger Beam
Disassembly/Reassembly . 20-188
07/09/20 19:31:51 62TA000B_200_0002
Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior Trim
Fenderwell
Openers
Frame
......................
...............................................
...............
...
...........................................
......
.......

.......
.....
................
.......
...........................................
................
.........
..............................
..............
...........................................
.....
...........................................
........
...........................................
...
......................
...............................................
...............
...
...........................................
......
.......
.......
.....
................
.......
...........................................
................
.........
..............................

..............
...........................................
.....
...........................................
........
...........................................
...
Component Location Index . 20-191
Front Seat Active Head Restraint
Inspection . 20-193
Front Seat Removal/Installation . 20-194
Front Seat Recline Motor Replacement . 20-200
Front Seat Lumbar Support
Replacement . 20-201
Front Seat Slide Motor Replacement . 20-203
Front Seat Slide Lever Replacement . 20-206
Front Seat Torsion Bar Replacement . 20-207
Rear Seat Access Cable Replacement . 20-208
Front Seat Frame Replacement . 20-209
Front Seat-back Cover Replacement . 20-214
Front Seat Cushion Cover
Replacement . 20-224
Rear Seat Removal/Installation . 20-236
Rear Seat-back Latch Replacement . 20-239
Rear Seat-back Release Lever/Cable
Removal/Installation . 20-240
Rear Seat Armrest Replacement . 20-241
Trunk Pass-through Lid Lock Cylinder
Replacement . 20-242
Trunk Pass-through Lid Replacement . 20-243

Rear Seat Armrest Beverage Holder
Replacement . 20-243
Rear Seat-back Cover Replacement . 20-245
Rear Seat Side Bolster Cover
Replacement . 20-249
Rear Seat Cushion Cover Replacement . 20-249
.........
...........................................
.................
..........
...........................................
.........
...........................................
.................
..........
...........................................
Front Bumper Removal/Installation . 20-251
Front Bumper Fog Light Cover
Replacement . 20-254
Front Air Spoiler Replacement . 20-255
Rear Bumper Removal/Installation . 20-256
Rear Bumper Finisher Cover
Replacement . 20-259
......................................
............................
....................
............
......................................
............................
....................

............
Hood Adjustment . 20-260
Hood Seal Replacement . 20-261
Hood Insulator Replacement . 20-262
Hood Support Strut Replacement . 20-262
................................
........
......
..............
...........................................
................................
........
......
..............
...........................................
Trunk Lid Adjustment . 20-263
Trunk Lid Torsion Bar Replacement . 20-264
Trunk Lid Weatherstrip Replacement . 20-265
Trunk Lid Cushion Replacement . 20-265
Trunk Lid Dynamic Damper
Replacement . 20-266
.........................
................
.........................
................
Fuel Fill Door Adjustment . 20-267
Fuel Cap Adapter Replacement . 20-268
...............
..........................
..............

..........................
......................
...
...............
..................
...............
..........................
..............
..........................
......................
...
...............
..................
Front Grille Cover Replacement . 20-269
Front Grille Replacement . 20-270
Front Fender Trim Replacement . 20-272
Cowl Cover Replacement . 20-273
Roof Molding Replacement . 20-275
Side Sill Protection Tape Replacement . 20-279
Trunk Lower Trim Replacement . 20-281
Emblem/Sticker Replacement . 20-284
.............
............
..........
..
.............
...............
....................
.............
............

..........
..
.............
...............
....................
Front Inner Fender Replacement . 20-288
Front Splash Shield Replacement . 20-289
Front Fender Fairing Replacement . 20-290
Middle Floor Undercover Replacement . 20-291
Fuel Pipe Protector Replacement . 20-292
Rear Inner Fender Replacement . 20-292
Rear Air Outlet Replacement . 20-293
......................
............
..................
..........................
.........
...........................................
...................
......................
............
..................
..........................
.........
...........................................
...................
Component Location Index . 20-294
Hood Opener Cable Replacement . 20-295
Trunk Lid Opener Cable/Fuel Fill Door
Opener Cable Replacement . 20-297

Hood Latch Replacement . 20-302
Hood Release Handle Replacement . 20-303
Trunk Lid Opener/Fuel Fill Door Opener
Replacement . 20-304
Trunk Lid Latch Replacement . 20-305
........................
..
...........................................
............................
...................................
........................
..
...........................................
............................
...................................
Frame Brace Replacement . 20-307
Rear Wheelhouse Gusset Replacement . 20-307
Middle Cross-member Gusset
Replacement . 20-308
Subframe Replacement . 20-309
Frame Repair Chart . 20-312
07/09/20 19:31:51 62TA000B_200_0003
０１
０１
ＴＡ０８Ｅ０００００００００Ｊ２００１ＰＡＡＴ００
Ref. No. Tool Number Description Qty
20-2
Body
Special Tools
07AAF-SNAA100 Torsion Bar Assembly Tool 1

070AG-SJAA10S Frame Positioning Guide Pin 1
07/09/20 19:31:51 62TA000B_200_0004
＊０１
ＴＡ０８Ｅ１４Ｊ１６１２６７０００００ＤＡＡＴ００
2-door
20-3
Doors
Component Location Index
FRONT PULL
POCKET CAP
ARMREST
SWITCH PANEL
POWER WINDOW SWITCH
ORNAMENT PANEL
GRIP BASE
FRONT DOOR
PANEL CAP
POWER MIRROR
SWITCH
DOOR GLASS INNER
WEATHERSTRIP
Passenger’s side
SWITCH PANEL
POWER WINDOW SWITCH
DOOR PANEL
UPPER
GRIP
BRACKET
LOWER GRIP
BRACKET

(cont’d)
Removal/Installation, page 20-12
07/09/20 19:31:52 62TA000B_200_0005
＊０２
2-door (cont’d)
20-4
Doors
Component Location Index (cont’d)
DOOR SASH INNER TRIM
DOOR SASH OUTER TRIM
DOOR OUTER MOLDING
DOOR GLASS
OUTER WEATHERSTRIP
HINGE
HINGE
DOOR
CHECKER
DOOR
DOOR WEATHERSTRIP
SPEAKER
PLASTIC COVER
Replacement, page 20-29
Replacement, page 20-31
Replacement, page 20-33
Replacement, page 20-31
Position Adjustment, page 20-51
Replacement, page 20-34
07/09/20 19:31:53 62TA000B_200_0006
＊０３
20-5

GLASS
IMMOBILIZER and
SECURITY LABEL
REGULATOR
CENTER LOWER CHANNEL
OUTER
HANDLE
COVER
OUTER HANDLE SEALS
OUTER HANDLE BASE
LOCK CYLINDER
(Driver’s)
STRIKER
LATCH
INNER HANDLE CABLE
INNER HANDLE
LATCH CABLE
OUTER HANDLE
FRONT LOWER CHANNEL
GLASS RUN CHANNEL
INNER HANDLE CAP
LATCH PROTECTOR
Passenger’s side
OUTER HANDLE HOLDER
Replacement, page 20-26
Adjustment, page 20-50
Replacement, page 20-26
Adjustment, page 20-53
Replacement, page 20-23
Replacement, page 20-19

07/09/20 19:31:55 62TA000B_200_0007
＊０１
ＴＡ０８Ｅ１３Ｊ１６１２６７０００００ＤＡＡＴ０１
4-door Front door
20-6
Doors
Component Location Index (cont’d)
ARMREST
SWITCH PANEL
POWER WINDOW SWITCH
ORNAMENT PANEL
POWER MIRROR SWITCH
DOOR GLASS INNER
WEATHERSTRIP
SWITCH PANEL
POWER WINDOW SWITCH
COURTESY LIGHT LENS
DOOR PANEL
LHD Passenger’s side
SWITCH PANEL
POWER WINDOW SWITCH
RHD Passenger’s side
Removal/Installation, page 20-16
07/09/20 19:31:56 62TA000B_200_0008
＊０２
20-7
DOOR SASH INNER TRIM
DOOR SASH OUTER TRIM
DOOR OUTER MOLDING
DOOR GLASS

OUTER WEATHERSTRIP
HINGE
HINGE
DOOR
CHECKER
DOOR
DOOR WEATHERSTRIP
SPEAKER
PLASTIC COVER
(cont’d)
Replacement, page 20-30
Replacement, page 20-31
Replacement, page 20-33
Replacement, page 20-31
Position Adjustment, page 20-51
Replacement, page 20-34
07/09/20 19:31:57 62TA000B_200_0009
＊０３
4-door Front door (cont’d)
20-8
Doors
Component Location Index (cont’d)
GLASS
IMMOBILIZER and
SECURITY LABEL
REGULATOR
CENTER LOWER CHANNEL
OUTER
HANDLE
COVER

OUTER HANDLE SEALS
OUTER HANDLE BASE
LOCK CYLINDER
(Driver’s)
STRIKER
LATCH
INNER HANDLE CABLE
INNER HANDLE CAP
INNER HANDLE
LATCH CABLE
OUTER HANDLE
FRONT LOWER CHANNEL
GLASS RUN CHANNEL
LATCH PROTECTOR
DOOR PANEL BRACKET
Passenger’s side
OUTER HANDLE HOLDER
Replacement, page 20-26
Adjustment, page 20-50
Replacement, page 20-26
Adjustment, page 20-53
Replacement, page 20-23
Replacement, page 20-19
07/09/20 19:31:59 62TA000B_200_0010
＊０１
ＴＡ０８Ｅ１ＪＪ１６１６６２０００００ＤＡＡＴ００
4-door Rear door
20-9
ARMREST
POWER WINDOW SWITCH

ORNAMENT PANEL
DOOR GLASS INNER
WEATHERSTRIP
SWITCH PANEL
DOOR PANEL
ASHTRAY
(cont’d)
Removal/Installation, page 20-35
07/09/20 19:31:59 62TA000B_200_0011
＊０２
4-door Rear door (cont’d)
20-10
Doors
Component Location Index (cont’d)
DOOR SASH INNER TRIM
DOOR OUTER MOLDING
DOOR GLASS
OUTER WEATHERSTRIP
HINGE
HINGE
DOOR
CHECKER
DOOR
DOOR WEATHERSTRIP
PLASTIC COVER
DOOR SASH OUTER TRIM
Replacement, page 20-45
Replacement, page 20-48
Replacement, page 20-47
Position Adjustment, page 20-51

Replacement, page 20-49
Replacement, page 20-46
07/09/20 19:32:01 62TA000B_200_0012
＊０３
20-11
GLASS
REGULATOR
OUTER HANDLE SEALS
OUTER HANDLE BASE
STRIKER
LATCH
INNER HANDLE CABLE
INNER HANDLE CAP
INNER HANDLE
LATCH CABLE
OUTER HANDLE
GLASS RUN CHANNEL
FUEL CONSUMPTION
LABEL (KD model)
OUTER HANDLE COVER
REAR LOWER
CHANNEL
OUTER HANDLE HOLDER
CHILD LOCK CAP
QUARTER GLASS
LATCH PROTECTOR
Replacement, page 20-42
Adjustment, page 20-50
Replacement, page 20-42
Adjustment,

page 20-53
Replacement, page 20-40
Replacement, page 20-38
Replacement, page 20-285
Replacement, page 20-42
07/09/20 19:32:03 62TA000B_200_0013
＊０１
＊０２
＊０３
＊０４
ＴＡ０８Ｅ１４Ｊ１６１２６７２１４０１ＫＤＡＴ００
2-door
20-12
Doors
Front Door Panel Removal/Installation
A
B
Fastener Locations
:Screw,2A:Screw,1B
A
B
A
C
Fastener Location
:Screw,1
A
Fastener Location
:Screw,1
A
B

C
D
E
F
C
NOTE:
• Take care not to scratch the door and related parts.
• When removing components, use the trim tools or
equivalent.
1. Remove the tweeter cover (see page 20-56).
2. Raise the glass fully.
3. Push on the bottom of the inner handle cap (A)
while pushing on the upper hook (B) with the
appropriate trim tool, then pull back the cap to
remove it.
4. Remove the screws (A, B) securing the inner handle
(C).
5. Remove the front pull pocket cap (A), and remove
the screw.
6. Pry up the notch (A) of the front door panel cap (B),
then pull back the cap to detach the hooks (C), and
release the hooks (D), then remove the cap.
7. Remove the screw, and disconnect the power
window switch connector (E) and the power mirror
switch connector (F).
07/09/20 19:32:04 62TA000B_200_0014
＊０５
＊０６
＊０７
＊０８

20-13
Fastener Locations
:Clip,10
(Gray)
A
B
C
D
A
B
C
C
A
B
A
B
C
D
E
F
G
8. Remove the door panel (A) with as little bending as
possible to avoid creasing or breaking it.
–1 Start at the bottom edge of the door panel,
release the clips with a commercially available
trim pad remover.
–2 Detach the upper clips.
–3 Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (B) and the latch
cable (C) are connected to the inner handle (D).

Do not pull the door panel up too far, or these
cables will be damaged.
9. While holding the door panel (A) away from the
door, remove the inner handle (B) from the door
panel by releasing the hooks (C).
10. Remove the door panel (A) while pulling the inner
handle (B) out through the hole in the door panel.
11. Disconnect the inner handle cable (A) and the latch
cable (B) from the inner handle (C), then remove
the handle.
–1 Detach the inner handle cable fasteners (D, E),
then disconnect the inner handle cable from
the cable fasteners.
–2 Detach the latch cable fastener (F), and remove
the latch cable fastener (G) from the inner
handle by pinching its tabs out.
NOTE: Check if the cable fasteners are
damaged or stress-whitened.
(cont’d)
07/09/20 19:32:04 62TA000B_200_0015
＊０９
＊１０
20-14
Doors
Front Door Panel Removal/Installation (cont’d)
A
B
C
D
E

D
D
D
Fastener Locations
:Screw,4 :Clip,3
Fastener Locations
:Screw,2A:Scerw,3B:Screw,1C
A
B
C
D
E
F
A
B
B
12. Remove the ornament panel (A).
–1 Remove the screws from back of the door
panel (B).
–2 Release the hooks (C) from back of the door
panel.
–3 Detach the hooks (D) and the clips from the
grip base (E).
13. Remove the screws (A, B, C), then remove the grip
base (D) and the upper grip bracket (E) from the
door panel (F).
07/09/20 19:32:05 62TA000B_200_0016
＊１１
＊１２
＊１３

20-15
Fastener Locations
:Screw,7
:Clip,3
A
C
B
D
D
E
D
Fastener Locations
:Screw,3
A
B
C
47 mm (1.85 in.)
A
B
14. Remove the switch panel (A) and the armrest (B) as
an assembly from the door panel (C).
–1 Remove the screws from the back of the door
panel.
–2 Pull out along the edge of the armrest to
release all of the hooks (D).
–3 Pull out along the edge of the switch panel to
release the hooks (E) and to detach the clips.
15. Remove the screws, and release the hook (A), then
separate the switch panel (B) and the armrest (C).
16. Install the door panel in the reverse order of

removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Replace any damaged cable fasteners with new
ones.
• The latch cable (A) should be fixed to the cable
fastener (B) with the latch in the unlocked
position as shown.
• Make sure the connectors are plugged in
properly, and the cables are connected securely.
• Make sure the window and power door lock
operate properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
07/09/20 19:32:05 62TA000B_200_0017
＊０１
＊０２
＊０３
＊０４
ＴＡ０８Ｅ１３Ｊ１６１２６７２１４０１ＫＤＡＴ０１
4-door
20-16
Doors
Front Door Panel Removal/Installation (cont’d)
A
B
Fastener Locations
:Screw,2
A

A
B
Fastener Location
:Screw,1
A
B
C
D
Fastener Locations
: Clip, 8
(Gray)
NOTE:
• Take care not to scratch the door and related parts.
• When removing components, use the trim tools or
equivalent.
1. Remove the tweeter cover (see page 20-56).
2. Raise the glass fully.
3. Push on the bottom of the inner handle cap (A)
while pushing on the upper hook (B) with the
appropriate trim tool, then pull back the cap to
remove it.
4. Remove the screws securing the inner handle (A).
5. Pry up the notch (A) of the lid (B), then pull back the
lid, and remove the screw.
6. Remove the door panel (A) with as little bending as
possible to avoid creasing or breaking it.
–1 Start at the bottom edge of the door panel,
release the clips with a commercially available
trim pad remover.
–2 Detach the upper clips.

–3 Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (B) and the latch
cable (C) are connected to the inner handle (D).
Do not pull the door panel up too far, or these
cables will be damaged.
07/09/20 19:32:06 62TA000B_200_0018
＊０５
＊０６
＊０７
＊０８
20-17
A
B
C
C
A
B
C
D
E
F
A
B
C
D
E
F
G
Fastener Location
:Clip,1

A
B
C
D
C
7. While holding the door panel (A) away from the
door, remove the inner handle (B) from the door
panel by releasing the hooks (C).
8. Remove the door panel (A) while pulling the inner
handle (B) out through the hole in the door panel.
While holding the door panel away from the door,
disconnect the power window switch connector (C),
the power mirror switch connector (D), and the
courtesy light bulb socket (E), and detach the
harness clip (F).
9. Disconnect the inner handle cable (A) and the latch
cable (B) from the inner handle (C), then remove
the handle.
–1 Detach the inner handle cable fasteners (D, E),
then disconnect the inner handle cable from
the cable fasteners.
–2 Detach the latch cable fastener (F), and remove
the latch cable fastener (G) from the inner
handle by pinching its tabs out.
NOTE: Check if the cable fasteners are
damaged or stress-whitened.
10. Remove the switch panel (A) from the door panel
(B).
–1 Detach the rear clip.
–2 Pull out along the edge of the panel to release

all of the hooks (C).
–3 Pull the switch panel rearward to release the
front hook (D).
(cont’d)
07/09/20 19:32:07 62TA000B_200_0019
＊０９
＊１０
＊１１
20-18
Doors
Front Door Panel Removal/Installation (cont’d)
Fastener Locations
:Screw,5
A
B
C
Fastener Locations
:Screw,6
A
B
C
D
E
C
B
D
46.5 mm (1.83 in.)
A
B
11. Remove and loosen the screws from back of the

door panel (A), and release the hook (B), then
remove the armrest (C).
12. Remove the screws from back of the door panel (A),
and release the hooks (B, C, D), then remove the
ornament panel (E).
13. Install the door panel in the reverse order of
removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Replace any damaged cable fasteners with new
ones.
• The latch cable (A) should be fixed to the cable
fastener (B) with the latch in the unlocked
position as shown.
• Make sure the connectors are plugged in
properly, and the cables are connected securely.
• Make sure the window and power door lock
operate properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
07/09/20 19:32:07 62TA000B_200_0020
＊０１
＊０２
＊０３
＊０４
ＴＡ０８Ｅ００Ｊ１６１２６７２１３０１ＫＢＡＴ００
2-door
4-door
2-door

4-door
20-19
Front Door Outer Handle Replacement
A
B
C
D
B
A
B
C
D
A
B
NOTE: Put on gloves to protect your hands.
1. Remove the door panel:
• 2-door (see page 20-12)
• 4-door (see page 20-16)
2. Disconnect the power door lock actuator connector
(A), and detach the harness clips (B).
3. Remove the rear plug cap (C), then remove the
plastic cover (D) as needed.
NOTE: Remove the glue from the door surface. If
the plastic cover is damaged or torn, replace it.
4. Remove the maintenance cap (A) (2-door) or the
hole seal (B) (4-door).
(cont’d)
07/09/20 19:32:08 62TA000B_200_0021
＊０５
＊０６

20-20
Doors
Front Door Outer Handle Replacement (cont’d)
A
B
C
D
E
A
E
B
Fastener Location
:Bolt,1
6x1.0mm
8N·m
(0.8 kgf·m, 6 lbf·ft)
B
A
5. Driver’s door: Pull both side flanges (A) of the
retainer (B) outward, and pull the middle flange
portion (C) of the outer casing cover (D) out, then
disconnect the cylinder cable (E) from the latch.
4-door is shown; 2-door is similar.
6. 2-door: Pull the glass run channel (A) away as
needed, and remove the bolt, then remove the
center lower channel (B) by pulling it downward.
07/09/20 19:32:08 62TA000B_200_0022
＊０７
＊０８
＊０９

＊１０
Driver’s door
Passenger’s door
Driver’s door
Passenger’s door
20-21
Fastener Location
:Bolt,1
A
B
B
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
Fastener Location
:Bolt,1
A
B
B
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
D
A
C
D
7. While holding the outer handle cover (A) from
outside of the door, loosen the bolt (driver’s door)

until it can be pulled out half-way by hand, or
remove the bolt (passenger’s door), and then
release the hooks (B) of the outer handle cover,
then remove the cover.
8. Release the hooks (A), then remove the lock
cylinder (B) (driver’s door) or the outer handle
holder (C) (passenger’s door) from the outer handle
base (D).
(cont’d)
07/09/20 19:32:09 62TA000B_200_0023
＊１１
＊１２
＊１３
＊１４
20-22
Doors
Front Door Outer Handle Replacement (cont’d)
A
B
C
C
A
A
B
D
A
B
B
C
Fastener Location

:Nut,1
A
B
C
D
E
6x1.0mm
4.9 N·m
(0.5 kgf·m,
3.6 lbf·ft)
C
9. Driver’s door: If the retainer (A) of the lock cylinder
cable (B) is damaged, release the hooks (C), then
replace it.
10. Pull the outer handle (A) back, and out as shown to
remove it from the door. Take care not to scratch
the door.
11. Release the hooks (A, B), then remove the outer
handle front seal (C) and the outer handle rear seal
(D).
12. Remove the outer handle base (A).
–1 Detach the rod fastener (B).
–2 With a clip remover, disconnect the outer
handle rod (C).
–3 Loosen the nut.
–4 Release the hook (D), and slide the outer
handle base forward to release the special bolt
(E) from the door panel.
07/09/20 19:32:10 62TA000B_200_0024
＊１５

＊０１
ＴＡ０８Ｅ００Ｊ１６１２６７２０８０１ＫＢＡＴ００
20-2320-23
Front Door Latch Replacement
B
A
6x1.0mm
8N·m
(0.8 kgf·m, 6 lbf·ft)
A
B
Fastener Location
:Bolt,1
13. Remove the rod fastener (A) from the outer handle
base (B), then replace it with a new one.
14. Install the handle in the reverse order of removal,
and note these items:
• Reinstall the lock cylinder (driver’s door) or the
outer handle holder (passenger’s door) before
installing the outer handle cover.
• Make sure that the actuator connector is plugged
in properly, and that the cylinder cable and the
outer handle rod are connected securely.
• Make sure the door key cylinder/door locks
operate properly.
• Make sure the door handle works properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
NOTE: Put on gloves to protect your hands.

1. Remove the door panel and the inner handle:
• 2-door (see page 20-12)
• 4-door (see page 20-16)
2. Remove the plastic cover as needed (see step 2 on
page 20-19).
3. Detach the rod fastener, and disconnect the outer
handle rod from the outer handle base (see step 12
on page 20-22).
4. Driver’s door: Disconnect the cylinder cable from
the latch (see step 5 on page 20-20).
5. 2-door: Pull the glass run channel away as needed,
and remove the bolt, then remove the center lower
channel by pulling it downward (see step 6 on page
20-20).
6. 4-door: Pull the glass run channel (A) away as
needed, and remove the bolt, then remove the
center lower channel (B) by pulling it downward.
(cont’d)
Replace.
07/09/20 19:32:10 62TA000B_200_0025