Nghệ thuật xếp hình Nhật Bản: penguin_2

 ✁
✂
✄☎
✆
✂
✝ ✞
✟
✠☛✡
☞
✌
1. Colored face is behind.
Rabbit ear on both sides.
4. Valley fold down at right angle. 5. Unfold back to step 4.
3-5
in mirror image.
6. Repeat steps 3 to 5
7. Open lower flap while raising
8. Inverse rabbit ear top flap.
9. Squash fold up.
10. Valley fold down. 11. Squash fold the white flap.
2. Swing upper flap down behind.
it up, using existing creases.
3. Valley fold lower flap at .
right angle. Precrease upper
left flap at angle bisector.
✍✎
✠☛✏
 
✡
✑
✡

✒
✑
✟
✓
✔☛✕
✖
✖
✖
✗✘
✙
✚✛
✜
✙
✢ ✣✥✤
✦☛✧★
✩
24. Squash fold on both sides.
13. Valley fold white flap
to the left.
14. Valley fold one flap
down (some paper has to be
16. Petal fold.15. Squash fold front flap.
17. Flip white flap to the left.
Repeat steps 13 to 16 in mirror
image.
13-16
12. Petal fold the white
flap. Then flip the back
flap up.
pulled out.)

right angle to form the arms.
18. Valley fold both flaps at
19. Precrease so that
both corners meet in the
center.
Note the black dots, used
as reference on step 21.
20. Valley fold down
21. Valley fold up so
that the crease meets the
black dots marked on step
19.
23. Squash fold the small triangular flap.
(part of it is hidden behind the horizontal
flap)
22. Turn Over
✪✫
✦☛✬
✗
✧✭
✧✮
✭
✤
✯
✰
★
✱
✱
✱
✲✳

✴
✵✶
✷
✴
✸ ✹✥✺
✻☛✼
✽
✾
30. Open both flaps.
Model wont lie flat.
facultative).
flaps to front. (These steps are
inside poket, raise two triangulars
25. Hide both upper flaps
31. Montain fold behind using
existing crease.
32. Close flaps back.
33. Valley fold at angle bissector. 34. Valley fold down. 35. valley fold up.
36. Precrease at right angle.
in half while making a rabbit
ear at the top to form the head.
37. Mountain fold the model
then unfold to step 27.
28. Precrease in half.
29. Precrease in half,
24. Squash fold on both sides.
26. Precrease, then turn over.
27. Valley fold down using
crease made on step 26.
23(bis). Valley fold on both

sides using existing creases.
✿❀
✻☛❁
✲
✼❂
✼❃
❂
✺
❄
❅☛❆
❇
❇
❇
❈❉
❊
❋●
❍
❊
■ ❏✥❑
▲☛▼◆
❖
38. Inside reverse fold where indicated,
to form the arms. Shape the head using
montain fold and pushing it slightly down
(it will make it 3D). Crimp the legs to form
the feet.
29. Round the body by inserting a
finger between the two main flaps.
40. The two pointed flaps can be raised
a little and tucked inside one another to

somewhat close the model in a rounded
shape.
41. finished.
◗
▲☛❘
❈
▼❙
▼❚
❙
❑
❯
❱☛❲
❳
❳
❳