Tài liệu Next Generation Frame 600 mm Products Table of Contents doc

Next Generation Frame (NGF)
600 mm Product Family
Ordering Guide
6/03 • 852
Next Generation Frame 600 mm Products
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products
Table of Contents
Introduction ..................................................................................................................................1
Frames
Fiber Main Distributing Frame (FMDF) ................................................................................................2
Front Facing Fiber Main Distributing Frame (F3MDF)..........................................................................3
Fiber Slim Rack ..................................................................................................................................4
Blocks
Fiber Termination Blocks (FTB) Unterminated......................................................................................5
Cable Clamping Kit ............................................................................................................................6
Fiber Termination Blocks Preterminated ..........................................................................................7-8
Fiber Combination Blocks (FCB) ....................................................................................................9-11
Sliding Adapter Packs ......................................................................................................................12
Mini Value-Added Modules (Mini VAMs) ..................................................................................13-21
Accessories
Fiber Optic Terminal Jumper Storage Bay ........................................................................................22
Equipment Bay ................................................................................................................................23
End Guard........................................................................................................................................24
Cable Clamp Kits ............................................................................................................................24
Rack Installation Kits ........................................................................................................................24
AC Outlet Kits..................................................................................................................................24
Ultra Physical Contact Fiber Optic Patch Cords ..........................................................................25-26
Index ..............................................................................................................................................27
6/03 • 852
Next Generation Frame 600 mm Products

1
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products
Introduction
Unprecedented growth in the telecommunications industry has driven wide-spread deployment of optical
fiber over the past few years. As a result, many service providers are finding that their existing fiber frames
and troughs are overflowing with large masses of optical fiber patch cords. In addition, the rapid
deployment of SONET/SDH, fiber in the loop and video initiatives has created the demand for increased
termination density at the fiber distributing frame. Service providers must build a sound network
infrastructure that will provide a solid base for delivering the new and enhanced broadband services
promised by the ever-advancing information superhighway.
What's Next?
It's clear that simply adding additional fiber frames to an existing FDF lineup is not the answer, as
conventional fiber frames allow only a small number of bays in a lineup before the horizontal trough
system becomes unmanageable. A more innovative fiber management plan is needed that will provide
unlimited expansion as well as alleviate jumper pile-up in the horizontal troughs.
With the introduction of its Next Generation Frame family of products, ADC offers the innovative solution
that service providers have been waiting for. Designed specifically to provide higher density while improving
fiber cable management, the Next Generation Frame product family allows for virtually unlimited growth.
Frames
ADC's Next Generation Frame product line has fiber frames designed to fit a variety of termination, splice,
and storage applications. Each frame option is designed with an emphasis on superior cable management
and ease of use, including features such as ample trough space for cable and jumpers, easy access to
connectors, and storage for jumpers. The frame sections are shipped from the factory fully equipped with
all cable management hardware including a built-in jumper storage panel.
Fiber Termination Blocks (FTB)
Fiber Termination Blocks (FTBs) are available with SC, FC, ST
®
and E-2000 adapters in block configurations
of 48, 72 or 96 positions. Also, 144 position FTBs are available using LX.5

®
and LC adapters. FTBs utilize
sliding adapter packs to gain easy access to both the front and rear connectors. There is also a block
configuration available to accommodate Mini Value-Added Modules (Mini VAMs) for applications requiring
splitters or WDMs. FTBs can be ordered with or without IFC or outside plant cable.
Fiber Combination Blocks Blocks (FCB)
Fiber Combination Blocks (FCBs) provide termination and on-frame splicing capabilities, all in one block.
The block occupies two mounting positions on the frame section. They are available with SC, FC, ST
®
and
E-2000 adapters in block configurations of 48, 72 or 96 positions. Also, 144 position FCBs are available
using LX.5
®
or LC adapters.
Features and Benefits
Ample Trough Space
Reduces jumper pile-up and congestion
- Reduces maintenance time due to easy removal
and tracing of jumpers
- Minimizes risk of microbends or damage to fiber
Built-in Jumper Storage Panel
Minimizes number of required jumper lengths
Maintains fiber bend radius
Simplifies frame installation
- Saves money by reducing the number of different
jumper lengths that have to be kept in inventory
- Minimizes risk of microbends or damage to fiber
Sliding Adapter Packs
Promotes high density
Provides easy access to connectors

- Saves valuable floor space
- Reduces time required for operations and
maintenance
Intelligent Cable Routing System
No fiber cross-over points
Multiple vertical troughways
- Reduces maintenance time due to easier
removal and tracing of jumpers and minimizes
fiber “weaving”
6/03 • 852
Next Generation Frame 600 mm Products
2
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products
Fiber Main Distributing Frame (FMDF)
The FMDF is the cornerstone of the NGF product line. This innovative frame has six rear horizontal
troughs. This abundant trough space minimizes fiber pile up and congestion leading to easier jumper
traceability and removal. The frame has twelve Fiber Termination Block (FTB) mounting positions equally
divided between vertical columns on the left and right sides of the frame as shown in the figure below.
The frame is 600 mm wide x 600 mm deep. The built-in jumper storage panel will store up to 5 meters
of jumper slack.
Catalog Number
NGF-ETSIMDF6060
Dimensions
2.2 m x 600 mm x 600 mm
Ordering Information
Description
600 mm FMDF Frame Section
600 mm 600 mm
FTB

Mounting
Position
(12)
Right
Vertical
Left
Vertical
Horizontal
Trough (6)
Jumper
Storage
Panel
Front ISO View
Front View
Side View
3
www.adc.com • +1-952-938-8080 • 1-800-366-3891
3/03 • 852
Next Generation Frame 600 mm Products
Next Generation Frame 600 mm Products
Front Facing Fiber Main Distributing Frame (F3MDF)
The F3MDF is designed for single-sided access applications and may be mounted up against a wall or
back-to-back to save floor space. Unlike the FMDF, the more compact F3MDF is equipped with a single
230 mm horizontal trough. The F3MDF has twelve FTB mounting positions equally divided between
vertical columns on the left and right sides of the frame as shown in the figure below. The frame is
600 mm wide x 480 mm deep. The built-in jumper storage panel will store up to 5 meters of
jumper slack.
2.2 m
600 mm 480 mm
Jumper

Storage
Panel
Right
Vertical
Left
Vertical
FTB
Mounting
Position
(12)
Horizontal
Trough (6)
Front ISO View
Front View
Side View
Catalog Number
NGF-ETSIF3MDF6048
Dimensions
2.2 m x 600 mm x 480 mm
Ordering Information
Description
600 mm F3MDF Frame Section
4
www.adc.com • +1-952-938-8080 • 1-800-366-3891
2.14 m
480 mm 480 mm
FTB
Mounting
Position
Jumper

Storage
Panel
3/03 • 852
Next Generation Frame 600 mm Products
Next Generation Frame 600 mm Products
Fiber Slim Rack
The Fiber Slim Rack is designed for lower density applications than the FMDF or F3MDF. It has six FTB
mounting positions and is designed for single-sided access applications. The Slim Rack is intended for
use in a single frame application and should not be used in a multiframe lineup. The built-in jumper
storage panel will store up to 5 meters of jumper slack.
When ordering FTBs for the Slim Rack, remember that only left oriented blocks are used on
this frame.
Front ISO View
Front View
Side View
Catalog Number
NGF-SLM7A100
Dimensions
2.14 m x 480 mm x 480 mm
Ordering Information
Description
NGF Fiber Slim Rack Frame Section
Catalog Number
NGF-TB
Block Style
1
2
3
4
1

2
4
3
SC
FC/ST
®
E-2000
LX.5
®
/LC
Cable Exit Direction
U
D
Upward
Downward
Block Configuration
A
B
C
M
48
72
96
144 (LX.5
®
or LC only)*
Block Orientation
L
R
Left

Right
Adapter Type
(62.5/125)
Multimode
9
A
5
Y
P
SC
FC
ST
®
LX.5
®
(144 only)
LC
(144 only)
OR
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N

X
K
SC ultra polish
SC ultra polish,
zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish,
zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®
ultra polish
(144 only)
LX.5
®
angled polish
(144 only)
LC ultra polish
(144 only)
5
6/03 • 852
Next Generation Frame 600 mm Products
5
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products

Fiber Termination Blocks (FTB) Unterminated
FTBs without fiber can be ordered fully loaded with adapters or empty (no adapters), in which case the
adapter packs for the block must be ordered separately (see page 12). Before ordering, determine the
block orientation and cable exit direction. Unterminated FTBs may be ordered with a “left” orientation
(mounts on the left side of the frame) or a “right” orientation (mounts on the right side of the frame).
The cable exit direction will be either “upward” (cables terminated to the rear side of the block exit up
toward the top of the frame) or “downward” (cables terminated to the rear side of the block exit down
toward the bottom of the frame). All blocks with adapters only are configured to terminate single or
dual jumpers on the rear of the block. If a multi-fiber breakout style cable (i.e., OSP/IFC) is to be
terminated to the rear of the block, a separate clamping kit is required (see page 6).
Definition of Variables
1
2
3
4
5
Block Style
General adapter type required in the FTB
Block Configuration
Maximum number of terminations that the FTB will accommodate when fully loaded
Block Orientation
Vertical column of the frame the FTB is to be mounted on
Cable Exit Direction
Direction the equipment jumpers or OSP cable will exit from the FTB
Adapter Type
Specific adapter type required in the FTB
* 144 blocks using style 1, 2, or 3 cannot be used
in 26" wide NGF frames
6/03 • 852
Next Generation Frame 600 mm Products

6
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products
Fiber Termination Blocks
Clamping kit includes: Cable clamp, protective cover and fanout bracket. It is required when terminating
a multifiber breakout style cable to the rear of the block.
72 position block loaded
with jumpers
72 position block loaded with
multifiber breakout cable
72 position block with
clamping kit
Protective
Cover
Fanout
Bracket
Cable Clamping Kit
Rear Cable Management Tray
for 144 Block Conversion Kit
Description Catalog Number
Block style originally purchased
All 48- and 72-position blocks NGF-ACCOSPKIT02
96-position blocks with rear cable management NGF-ACCOSPKIT01
as shown above (blocks ordered before June 2002
96- or 144-position Left Up Blocks NGF-ACCRCMSLU
96- or 144-position Right Up Blocks NGF-ACCRCMSRU
96- or 144-position Left Down Blocks NGF-ACCRCMSLD
96- or 144-position Right Down Blocks NGF-ACCRCMSRD
Ordering Information
6/03 • 852

Next Generation Frame 600 mm Products
7
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products
Fiber Termination Blocks (FTB) Preterminated
Preterminated FTBs are available with either indoor or outdoor rated cable in ribbon or stranded
configurations. All blocks are 100% factory tested to guarantee continuity and reliable connections.
Preterminated FTBs make installation quick and easy, reducing labor costs. Before ordering, determine
the block orientation and cable exit direction. Preterminated FTBs may be ordered with a “left”
orientation (mounts on the left side of the frame) or a “right” orientation (mounts on the right side of
the frame). The cable exit direction will be either “upward” (cables terminated to the rear side of the
block exit up toward the top of the frame) or “downward” (cables terminated to the rear side of the
block exit down toward the bottom of the frame).
Preterminated Fiber
Termination Blocks
arrive from the factory
with either IFC or
OSP Cables
Fiber cable easily uncoils
during installation
Fiber Termination Block
ships inside the drum
Ordering information follows on next page.
Fiber Termination Block
loaded with multifiber
breakout cable
Definition of Variables
1 Block Style
General adapter type required in the FTB
2 Block Configuration

Maximum number of terminations that the FTB will accommodate when fully loaded
3 Block Orientation
Vertical column of the frame the FTB is to be mounted on
4 Cable Exit Direction
Direction the equipment jumpers or OSP cable will exit from the FTB
5 Adapter/Connector #1
Specific adapter/connector type required in the FTB. Refers to the adapter/
connector type at the FTB
6 Connector #2
Specific connector type required at the cable end opposite the FTB
7 Cable Type
Type of cable to be terminated to the FTB
8 Cable Length
Required length of the cable terminated to the FTB
6/03 • 852
Next Generation Frame 600 mm Products
8
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Catalog Number
NGF-TB
†Other cable types are available upon request.
Please contact your ACD representative.
Glass Type
Glass Type
IFC Type Multimode
(62.5/125)
OR
OR
AM
BM

DM
2M
VM
WM
12 fiber stranded
24 fiber stranded
36 fiber stranded
48 fiber stranded
72 fiber stranded
96 fiber stranded
Corning
Corning
Corning
Corning
Corning
Corning
Length in
meters
Cable Length
XXX
8
Block Style
1
2
3
4
SC
FC/ST
®
E-2000

LX.5
®
/LC
Cable Exit Direction
U
D
Upward
Downward
Block Configuration
A
B
C
M
48
72
96
144
(LX.5
®

or
LC
only)**
Block Orientation
L
R
Left
Right
1
4

2
3
IFC Type Singlemode † Glass Type
ZB
ZC
ZD
AA
BA
CA
2A
7A
VA
DA
FH
GA
HA
MA
JA
KA
EG
FJ
KB
EF
FK
72 fiber stranded
96 fiber stranded
144 fiber stranded
12 fiber stranded
24 fiber stranded
36 fiber stranded

48 fiber stranded
54 fiber stranded
72 fiber stranded
96 fiber stranded
144 fiber stranded
12 fiber ribbon
24 fiber ribbon
36 fiber ribbon
48 fiber ribbon
72 fiber ribbon
96 fiber ribbon
144 fiber ribbon
72 fiber ribbon
96 fiber ribbon
144 fiber ribbon
House Cable*
House Cable*
House Cable*
Corning
Corning
Corning
Corning
Corning
Corning
Corning
Corning
Sumitomo
Sumitomo
Sumitomo
Sumitomo

Sumitomo
Sumitomo
Sumitomo
Alcatel
Alcatel
Alcatel
7
OSP Cable Type Singlemode
72 fiber ribbon dielectric
72 fiber stranded dielectric
96 fiber ribbon dielectric
96 fiber ribbon dielectric
96 fiber stranded dielectric
144 fiber stranded dielectric
144 fiber ribbon dielectric
VP
VT
VU
VW
EN
FL
FM
Alcatel
Pirelli
Alcatel
Pirelli
Pirelli
Pirelli
Pirelli
0

9
A
5
Y
P
No connector/stub end
SC
FC
ST
®
LX.5
®

(144 only)
LC (144 only)
Connector #2 Singlemode
0
7
8
L
2
3
Q
4
V
N
X
K
No connector/stub end
SC ultra polish

SC ultra polish, zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish, zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®

ultra polish (144 only)
LX.5
®

angled polish (144 only)
LC ultra polish (144 only)
Connector #2
Multimode (62.5/125)
OR
6
OR
Adapter/Connector #1
Multimode (62.5/125)
9
A
5
Y
P

SC
FC
ST
®
LX.5
®
(144 only)
LC (144 only)
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N
X
K
SC ultra polish
SC ultra polish,
zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish,
zirconia sleeve
FC 8° angled polish
ST

®
ultra polish
E-2000 angled polish
LX.5
®
ultra polish
(144 only)
LX.5
®
angled polish
(144 only)
LC ultra polish
(144 only)
5
Next Generation Frame 600 mm Products
Preterminated FTBs
See previous page for definition of variables.
* House cable will use Corning SMF28, Sumitomo,
Alcatel or similar singlemode fiber based on current
market availability.
** 144 blocks using style 1, 2, or 3 cannot be used
in 26" wide NGF frames
6/03 • 852
Next Generation Frame 600 mm Products
9
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Next Generation Frame 600 mm Products
Fiber Combination Blocks (FCB)
Fiber Combination Blocks provide a place to terminate pigtails and splice IFC/OSP cables on the frame.
The blocks are available with several different adapter types in block configurations of 48, 72, or 96

positions. Also, a 144 position FCB is available using an LX.5
®
adapter. The termination portion of the
fiber combination block utilizes sliding adapter packs to gain easy access to connectors on both the front
and rear side of the block. The block is available with factory-installed pigtails for easy installation. Splice
trays are shipped with the block if ordered with pigtails; otherwise trays must be ordered separately. The
block is shipped with a cable clamp for OSP/IFC. The FCB occupies two mounting positions on a frame
section. Before ordering, determine the block orientation. FCBs may be ordered with a “left” orientation
(mounts on the left side of the frame) or a “right” orientation (mounts on the right side of the frame).
Ordering information follows on next page.
6/03 • 852
Next Generation Frame 600 mm Products
10
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Catalog Number
NGF-CB
2
Splice Chip
0
1
2
3
6
7
8
9
4
Empty
Bare fusion
Heat shrink fusion

Mechanical (elastomeric)
Nortel QPAK
Swiss
®
ANT
Rotary
FibrLok
®
16 position heat shrink fusion
Block Style
1
2
3
4
SC
FC/ST
®
E-2000
LX.5
®
/LC
Block Configuration
A
B
C
M
48
72
96
144 (LX.5

®
or LC only)
1
2
Number of Pigtail
Assemblies
XX
Number of assemblies
6
Pigtail Type
0
1
2
4
5
No pigtails
12 fiber pigtail
12 fiber stranded
Maxi-Strip
8 fiber pigtail
12 fiber ribbon
5
7
Block Orientation
L
R
Left
Right
3
A

5
9
Y
P
FC
ST
®
SC
LX.5
®
(144 only)
LC (144 only)

4
OR
Adapter/Connector Type
Multimode (62.5/125)
Adapter Type
Singlemode
7
8
L
2
3
Q
4
V
N
X
K

SC ultra polish
SC ultra polish,
zirconia sleeve
SC 8° angled polish
FC ultra polish
FC ultra polish,
zirconia sleeve
FC 8° angled polish
ST
®
ultra polish
E-2000 angled polish
LX.5
®
ultra polish (144 only)
LX.5
®
angled polish
(144 only)
LC ultra polish (144 only)
4
1
Next Generation Frame 600 mm Products
Fiber Combination Blocks (FCB)
Definition of Variables
1
2
3
4
5

6
7
Block Style
General adapter type required in the FCB
Block Configuration
Maximum number of terminations that the FCB will accommodate when fully loaded
Block Orientation
Vertical column of the frame the FCB is to be mounted on
Adapter/Connector Type
Specific adapter/connector type required in the FCB
Pigtail Type
Type of pigtail required
Number of Pigtail Assemblies
Number of pigtails to be pre-installed in the FCB
Splice Chip
Type of splice chip required for splice trays
1
144 termination block requires the use of either:
Mechanical (elastomeric) splice tray when using mass fusion ribbon splicing
Nortel QPAK splice tray when using single fiber heat shrink fusion splicing
144 blocks using block style 1, 2, or 3 cannot be used in 26" wide NGF frames