Tài liệu Michigan Channels SE Practice CCIE Lab docx

SE Practice CCIE Lab
V1.4




Michigan
Channels
SE Practice
CCIE Lab



Cisco Systems Internal Use Only
1
SE Practice CCIE Lab
V1.4


Token
Ring
ISDN
ISP
IBM Mainframe
FEP
Frame Relay
VLAN A
VLAN B
s0/1
s0
s0/0

s1/3
s1/2
s1/1
s1/0
E0/0
FA1/0
3/1
3/2
e0/1
e0/0
s0/1
s0
e0
t0
to0
s0/0
s0
BRI
BRI
s0/0
2611
2611
3640
2513
2502
Cat 5K
e0/0
Network Schematic
Cisco Systems Internal Use Only
2

SE Practice CCIE Lab
V1.4



Token
Ring
ISDN
IGRP
ISP
IBM Mainframe
FEP
1
3
5
2
Frame Relay
IGRP
VLAN A
VLAN B
6
3/2
2611
2611
3640 2513
2502
Cat 5K
BGP
IGRP
Frame Relay

OSPF area 1
OSPF AREA 3
OSPF AREA 2
x.25 EIGRP
OSPF AREA 0
EIGRP


Routing Topology
Cisco Systems Internal Use Only
3
SE Practice CCIE Lab
V1.4


To R3
To R5
To R2
To R4
Serial 1/0
Serial 1/3
Serial 1/1
Serial 1/2
Cisco
3620
DLCI 20
DLCI 40
DLCI 50
DLCI 150 to DLCI 50
DLCI 120 to DLCI 20

DLCI 140 to DLCI 40




Cisco Systems Internal Use Only
4
SE Practice CCIE Lab
V1.4
Cisco Lab

Guidelines

At no time should the hardware/software configuration of frame switch (router 7) or ISP
(router 8) be modified in any way

At no time are Static or Default routes to be used

Do not configure loopback interfaces unless requested


Create the Network Diagram


Review all of the steps in this document before you begin. Some steps must take into
account information found later in this document. Create a network diagram on a
separate piece of paper. Include all network numbers, subnet masks, and host
addresses.

Catalyst Configuration

1.0 Create 2 VLAN’s on the Catalyst 5000. Port 3/1 in VLANA and port 3/2 in
VLANB

2.0 Configure R2s’s e0/0 as 129.45.80.1/30 which in connected to VLANB

3.0 Configure R3’s e0/0 as 129.45.80.49/30 which is connected to VLANA

Topology and Basic IP Setup

4.0 Configure R5’s s1 as 129.45.80.74 with a 2 host subnet

5.0 Configure IP addresses on the rest of the network with the address 129.45.80/24
5.1 Allow
at least
6 hosts per subnet on ethernet and token ring interfaces
5.2 Allow
at least
2 hosts per subnet on each WAN link

6.0 Configure IP across the Frame-Relay nework
6.1 Configure R3 using two sub-interfaces
6.2 Use a sub-interface for the connection to R5 and use one sub-interface for
the connection to R2 and R4. Do not configure sub-interfaces for R2, R4, or
R5
6.3 Ensure that you can ping from any router to any interface including your own

7.0 Configure the ISDN link. Verify pings from R3 – R5

8.0 Configure X.25 for the connection from R1 to R2

9.0 Configure async routing between the auxillary ports on R1 and R4

Cisco Systems Internal Use Only
5