Tài liệu 2 Mbps DSX Front Cross-Connect Solutions 600 mm 2 Mbps DSX Product Family pptx

10/03 • 100571
600 mm Products
122
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps DSX Front Cross-Connect Solutions
600 mm 2 Mbps DSX Product Family
Digital signal cross-connect (DSX) products are used to connect one piece of digital telecommunications
equipment to another. This simplifies equipment connections and provides a convenient test access point
as well as a convenient location for rearranging and restoring circuits. Cross-connecting network elements
of a DSX is a simple, efficient way of organizing a facility's digital telecommunications equipment.
There are three basic areas in a DSX. The wire termination area for terminating the signal (wire) from a
network element. The cross-connect area, used to connect the two DSXs that have terminated the signals
from two digital network elements. And finally, the heart of the DSX, the jack. Each DSX jack provides an
OUT, IN and MONITOR signal access point. The OUT and IN switching jacks provide direct access to the
network element's input and output signals. These jacks provide a means of temporarily breaking the
connection between DSX panels that are cross-connected together and allow access to the signals for test
and patching operations. A MONITOR jack with high impedance bridge networking is connected to the
OUT jack for nonintrusive access to the output signal of each network element.
At 2.048 Mbps rate, DSX-1 panels connect network equipment such as office repeater bays, channel
banks, multiplexers, digital switches, loop carriers, loop switches, radio, fiber optic systems, and other
2 Mbps equipment.
OUT
IN
DSX
PERMANENT
EQUIPMENT
CABLE
Network
Element A
Tx OUT
OUT OUT

IN
IN
Rx IN
X-OUT
X-IN
M
O
I
DSX
PERMANENT
EQUIPMENT
CABLE
Network
Element B
Tx OUT
X-OUT
X-IN
Rx IN
OUT
MON
MON
IN
Typical DSX
Semi-
Permanent
Cross
Connect
Jumper
LED
Tracer

Wire
Test
Box
Test
Box
Monitoring and testing with traditional DSX requires finding and going to two locations for complete circuit testing.
It also requires access to both DSX sites and the time necessary to travel and setup test gear in two locations.
DSX Features and Benefits
• OUT/IN jacks – Fast and easy access to circuits for testing, monitoring and patching
• Bantam die-cast jacks – Guarantees quality and reliability over time
• Flashing LEDs available in a variety of colors – Provides easy circuit identification
• Multiple designs and configurations – Design optimized for each application
• Coax and 120 Ohm connections provide the flexibility to connect 75 Ohm equipment to
120 Ohm equipment
DSX Introduction
Traditional DSX Application
10/03 • 100571
600 mm Products
123
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
The Products
The 600 mm skeleton bay is the basis of ADC’s 2 Mbps DSX product offering. The fully-assembled bay
meets the standard ETSI 600 mm wide x 2200 mm tall footprint. The fuse panel and all the necessary cable
management are factory-installed in the bay making installation and ordering fast and easy. DSX panels are
added in the field as needed. The 600 mm skeleton bay is compatible with all ADC 64-termination DSX
panels. A total of 832 twisted pair or coaxial terminations fit in each bay.
Loaded 600 mm Skeleton Bay
Empty 600 mm Skeleton Bay
DSX 64-Termination Panel
PxPlus

™
Panel
FlexDSX
™
Panel
2 Mbps DSX Front Cross-Connect Solutions
600 mm 2 Mbps DSX Product Family
10/03 • 100571
600 mm Products
124
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps DSX Front Cross-Connect Solutions
Product Selection Guide
FlexDSX
™
Panels
FlexDSX panels offer four-port jack access with dual monitor for applications where the cross-connect
may be located far away or is inaccessible such as in collocation applications. The dual monitor port also
allows for fast isolation of problems as both sides of the circuit can be accessed easily from one
termination. The jacks are individually removable and the backplane terminations are removable in groups
of four.
PxPlus
™
Panels
Ideal for applications requiring three-port jack access and true cost-deferment as equipment cables can be
preterminated and jacks can be added as needed. If the chassis has more than 60% of its terminations
turned up within one year, the fixed, non-modular DSX 64 panels may be a better choice for a high
growth environment.
DSX 64-Termination Panels
Ideal for applications where individual circuit modularity is not required. This is a fixed, non-modular

64 termination panel with three-port jack access.
Feature/Need FlexDSX PxPlus DSX 64
64 terminations/panel (Balun & twisted pair) X X X
Mounts in IBF-RSC021 skeleton bay X X X
(832) 2 Mbps terminations per bay X X X
Tracer LED X X X
Ability to prewire backplane X X X
Oversized labels X X X
In-service patching and circuit rearrangement X X X
Balun options (BNC & 1.6/5.6) X X X
Patching and monitoring capabilities X X X
Removable jacks X X
Dual monitor (4 port jacks) X
Variety of backplanes and connector options X
to fit into 1 chassis
10/03 • 100571
600 mm Products
125
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps DSX Front Cross-Connect Solutions
ADC 600 mm Skeleton Bay for FlexDSX
™
, PxPlus
™
and DSX64 Panels
The 600 mm skeleton bay is designed for FlexDSX, PxPlus and DSX 64-termination panels. The fully-
assembled bay meets the standard ETSI 600 mm wide x 2.2 meter tall footprint for easy office planning.
Rack mounting will also accommodate standard 48.26 cm (19 inch) panels. Fuse panels and all the
necessary cable management are factory-installed in the bay, making ordering and installation fast and easy.
DSX panels are added in the field as needed. OUT (Tx) and IN (Rx) cable ways for equipment terminations

support the use of either 120 Ohm twisted pair or 75 Ohm coaxial cable. The skeleton bay can be mounted
on either concrete or raised floor.
600 mm Empty Skeleton Bay
600 mm Skeleton Bay
Front Jumper Rings
(shown with panels installed)
600 mm
Extra rack space reserved for
miscellaneous applications
(such as cross aisle panels or monitor
panels) or for additional DSX panels
(up to [832] 2 Mbps terminations)
High-density supports up to (12)
5.25-inch (13.34 cm) panels or (768)
2 Mbps terminations (120 Ohm or
75 Ohm) per bay
Single part number simplifies
ordering and installation
Rings and troughs – preprovisioned
jumper management ensures existing
wiring is not disturbed during
expansion or maintenance
Cable tie down bars on the rear of
the bay eliminate the need for filler
panels and end guards
600 mm width aligns perfectly
with raised floor tile dimensions
and simplifies office engineering
and planning
Panels mount over the rings –

no need for removal of rings
during installation
All metric hardware allows easy
replacement for misplaced screws
Description
Skeleton bay front cross-connect
Catalog Number
IBF-RSC021
Ordering Information
Note: Bays come fully-loaded with cable troughs, cable rings, fuse panel and grounding kits.
The bay holds up to nine 7-inch (17.78cm) high modules.
10/03 • 100571
600 mm Products
126
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
The FlexDSX platform from ADC embodies the ultimate flexibility in circuit access. The 4-port jack card
provides dual monitor capability. Dual monitoring allows nonintrusive monitoring in both directions of a
2 Mbps signal from a single DSX location. Monitoring a circuit in both directions from a single DSX
location will save time when troubleshooting the network because test gear isn’t moved to a second DSX
location to test the complete circuit. Dual monitoring also gives access to complete circuits when the
other end of the cross-connection is not available, as in the situation where collocation of two carriers
exists and the cross-connection between DSX provide the point of interconnection.
FlexDSX products also provide flexibility in deploying your resources. The completely modular design
allows you to deploy modules and chassis on an as-needed basis. By creating a lineup of skeleton bays
and filling the bays with chassis and modules only as needed, you can defer capital expenses until the
equipment is ready to create a revenue stream.
In today's multinational, multiservice environment, FlexDSX products offer a variety of standard
terminations. From wire-wrap to coax to RJ45 connectors, FlexDSX products offer the option to terminate
2 Mbps equipment from a single location.
OUT

IN
FlexDSX
PERMANENT
EQUIPMENT
CABLE
Network
Element A
Tx OUT
OUT OUT
IN
IN
Rx IN
X-OUT
X-IN
M
O
I
FlexDSX
PERMANENT
EQUIPMENT
CABLE
Network
Element B
Tx OUT
X-OUT
X-IN
Rx IN
OUT
MON
MON

IN
Typical DSX
Semi-
Permanent
Cross
Connect
Jumper
LED
Tracer
Wire
Test
Box
MON
MON
FlexDSX products provide the convenience and time-saving feature of testing and
monitoring the signal in both directions from one location.
2 Mbps DSX Front Cross-Connect Solutions
FlexDSX
™
Introduction
FlexDSX
™
Application
Features
• Conduct protocol testing for both OUT and IN transmission directions from one location – saves time
when testing a circuit
• Staggered jack alignment – allows industry standard patch cords to be used side-by-side in high
density products
• Jumper rings and rear cable bars are installed on the skeleton bay – provides superior cable management
• OUT/IN equipment cable terminations on the backplane are modular in groups of four – allows for

multiple circuit count configurations (56, 64, 84)
• Works with twisted pair or coax cabling; choose wire-wrap, BNC or 1.6/5.6 interfaces – flexibility to
meet a variety of needs
• Coax and 120 Ohm connections provide the flexibility to connect 75 Ohm equipment to
120 Ohm equipment
10/03 • 100571
600 mm Products
127
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps DSX Front Cross-Connect Solutions
FlexDSX
™
Panels – Four-Port (Dual Monitor) Jack Access
FlexDSX panels are the only DSX panels in the industry that offer individual, removable jacks, removable
OUT/IN equipment cable terminations, and four-port (bidirectional) test access capabilities. The four-port
jack system consists of OUT and IN jacks for direct access to the network element’s input and output
signals, and DUAL MONITOR jacks for monitoring of the signal in both directions simultaneously at a single
location. Dual monitors are especially beneficial for testing when the other side of the cross-connect is
located far away, in another room, or is inaccessible (i.e., collocation).
FlexDSX Front View
FlexDSX panel with individual
jack card pulled out
FlexDSX four-port
jack card
Large labels provide clear documentation
of circuits
64-terminations per panel (Balun and twisted
pair) – matches 2.048 Mbps equipment
cabling breakouts
Large front trough avoids cable build-up

Tracer LED eliminates
manual tracing of circuits
for faster circuit
identification
Four-port (dual monitor)
jacks allow quick isolation
of problems in larger
applications where the
cross-connect may be
located far away or is
inaccessible
Individual
removable
jacks
Staggered jacks allow industry standard
patch cords to be used side-by-side
Chassis are configured with OUT/IN interfaces
in groups of four for easy removal and
minimal disturbance of adjacent circuits
FlexDSX Rear View
(1.6/5.6 Balun version shown)
10/03 • 100571
600 mm Products
128
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Description
Fully-loaded, 64-circuit panel – Wire-wrap cross-connects
5.25" (13.34 cm) high, 19" (48.26 cm), EIA/IEC mounting
120 Ohm wire-wrap equipment interface
120 Ohm wire-wrap equipment interface, rear dual

performance monitor
BNC Balun equipment interface
1.6/5.6 Balun equipment interface
SMB
RJ45
Shielded RJ45
7" (17.78 cm) high*, 19" (48.26 cm), EIA/IEC mounting
BNC equipment interface
1.6/5.6 equipment interface
Catalog Number
DFX-100001
DFX-100001-DPM
DFX-210001
DFX-220001
DFX-230001
DFX-400001
DFX-500001
DFX-210001-DPM*
DFX-220001-DPM*
Ordering Information
2 Mbps DSX Front Cross-Connect Solutions
FlexDSX
™
Panels – Four-Port (Dual Monitor) Jack Access
*The IBF-RSC024 skeleton bay holds nine 7-inch (17.78 cm) high panels
Module and Card
4-Port Jack Card with 4-Pack Module
4-Pack Module
with 1.6/5.6 connectors
4-Pack Module

with wire-wrap connectors
4-Pack Module
with BNC connectors
4-Port Jack Card
Description
FlexDSX 64-position empty chassis
19" (482.6mm) x 5.25" (133.35mm) (3RU)
4-pack modules
Wire-wrap, front cross-connect, 120 Ohm
BNC, front cross-connect, 75 Ohm
1.6/5.6, front cross-connect, 75 Ohm
RJ45, front cross-connect, 120 Ohm
Shielded RJ45, front cross-connect, 120 Ohm
SMB, front cross-connect, 75 Ohm
Circuit cards
FlexDSX jack, odd
FlexDSX jack, even
Catalog Number
DFX-9E0002
DFX-9E1000
DFX-9E2000
DFX-9E3000
DFX-9E4000
DFX-9E4000-S
DFX-9E5000
DFX-1
DFX-2
Ordering Information
10/03 • 100571
600 mm Products

129
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Description
All-front-access FlexDSX panels
Empty rack (holds 10 DFX-1F0001 chassis)
Fully-loaded panel
Empty chassis
Four pack module
All-front-access FlexDSX with performance monitoring
Empty rack (holds 8 DFX-1F0001-DPM chassis)
Fully-loaded panel
Empty chassis
Four pack module
Catalog Number
DFX-RSFA04
DFX-1F0001
DFX-9E0003
DFX-9F1000
DFX-RSFA03
DFX-1F0001-DPM
DFX-9E0003-DPM
DFX-9F1000-DPM
Ordering Information
2 Mbps Digital Cross-Connect System
All-Front-Access FlexDSX
™
Panels
The all-front-access FlexDSX product family, designed for 2.048 Mbps cross-connect applications for the
standard 600 mm footprint, provides 0.045" (1.14 mm) square wire-wrap pin interface options on both the
cross-connect and equipment fields and is available with or without performance monitoring. Each chassis

holds up to 16 four-circuit front access module packs. No internal wiring is required between modules and
the chassis or between adjacent modules. Each of the 64 individual jack cards in a fully-populated chassis
have four bantam-sized ports—monitor OUT, OUT, IN, and monitor IN, as well as a red flashing tracer lamp.
Monitor network resistors provide 120 Ohm impedance.
FlexDSX chassis without
performance monitoring
(Front View)
FlexDSX chassis with
performance monitoring
(Front View)
Four-Pack Modules
Four-Pack Modules
10/03 • 100571
600 mm Products
130
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps DSX Front Cross-Connect Solutions
PxPlus
™
Panels – Three-Port Individual Jack Modularity
The PxPlus panel was designed for 2 Mbps DSX cross-connect applications where individual jack modularity
is required. The PxPlus system consists of a 64-circuit empty panel and individual three-port jack access
cards that are sold separately. The empty panel can be loaded into the bay and precabled. When service is
ready to be turned up, the PxPlus jack cards are installed into the panel providing for true cost deferment.
PxPlus panel shown fully loaded
with circuit cards
PxPlus Panel with individual
jack card pulled out
Large removable labels provide easy documentation of
circuits to help avoid mistakes while trouble shooting.

Three-port
(single monitor)
jack access
allows easy
circuit access
for testing,
patching and
monitoring
Tracer LED eliminates manual tracing of
circuits for faster circuit identification
Designed for individual jack modularity – jacks are
ordered separately and installed upon service turn-up.
PxPlus panel shown empty
without circuit cards
Backplane can be fully prewired upon installation –
allows circuit cards to be added as needed for true
cost deferment
64 terminations per panel (Balun
and twisted pair) matches
equipment cabling breakouts
PxPlus panel (rear view)
(Wire-wrap version shown)
Description
64-circuit empty chassis –
Wire-wrap equipment interface
BNC Balun equipment interface
Jack card
Individual 120 Ohm
Catalog Number
PXP-532004

PXP-532003
PXP-A00006
Ordering Information
10/03 • 100571
600 mm Products
131
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps DSX Front Cross-Connect Solutions
DSX 64-Termination – Three-Port Fixed Panel
Each panel supports 64 2 Mbps terminations and provides three-port jack access for monitoring, patching
and testing. An LED provides easy identification of cross-connect cables by eliminating manual tracing of
wires. The equipment (OUT/IN) cables are terminated on the rear of the chassis via wire-wrap and Balun
options of 1.6/5.6 or BNC connectors. The cross-connects are terminated on the front via wire-wrap pins.
DSX 64-Termination Panel (Front View)
Front wire-wrap cross-connect pins for easy
circuit rearrangement
Large removable labels provide easy documentation of
circuits to help avoid mistakes while troubleshooting
64-terminations per panel (Balun and twisted
pair) – matches equipment cabling breakouts
DSX 64-Termination Panel (Rear View)
(BNC Balun version shown)
DSX 64-Termination Panel
Three-port (single monitor) jack access allows easy
circuit access for testing, patching and monitoring
Tracer LED eliminates manual tracing of circuits
for faster circuit identification
One part number allows for
easy ordering and installation
Description

64-termination panel
120 Ohm wire-wrap equipment interface
BNC Balun to wire-wrap equipment interface
1.6/5.6 Balun to wire-wrap equipment interface
Catalog Number
D1M-1A2016
D1M-1A2015
D1M-1A2017
Ordering Information
Features
• 64 terminations per panel (Balun and twisted pair) – matches 2.048 Mbps equipment cabling breakouts
• All panels mount into the ADC 600 mm skeleton bay IBF-RSC021 – one platform for all applications
• Tracer LED eliminates manual tracing of cross-connect wires for fast circuit identification
• Oversized labels for complete circuit identification
• In-service patching and circuit rearrangement allows circuit maintenance to be completed during business
hours without downtime by using ADC’s bridging office repeaters (Call your local ADC sales office for
more information)
• Balun terminations increase density by converting 75 Ohm equipment cables to 120 Ohm for cross-
connecting while still providing the flexibility of DSX jack access. Available in BNC and 1.6/5.6
10/03 • 100571
600 mm Products
132
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Digital Cross-Connect System
Bay Hardware and Accessories
End Guard
These 2.2 m high end guards provide protection and a finished appearance at the start and end
of the lineup.
DSX Frame Doors
The door kit provides left and right doors for the front and rear of the DSX frame. Also included are top,

front, and rear brackets for mounting of the doors to the frame.
Description
450 mm deep end guard
600 mm deep end guard
300 mm deep end guard
Catalog Number
RAC-EGK450*
RAC-EGK600*
RAC-EGK300*
Ordering Information
Description
DSX frame door kit
Catalog Number
IBF-1ENCDOR
Ordering Information
Description
End guard for use with DSX frame door kit
Catalog Number
IBF-1ENCEG
Ordering Information
End Guard for Use with Door Enclosure Kit
This end guard kit is used in conjunction with the DSX frame doors used to enclose the frame. It also
provides protection and a finished appearance to the start and end of the frame lineup.
Description
150 mm filler panel kit
300 mm filler panel kit that includes upper and lower
cable trough
Catalog Number
SFK-122150
SFK-122300

Ordering Information
Filler Panel Kits
The filler panel kits add spacing between DSX frames. The kits come in 150 mm and 300 mm
measurements.
* Each kit comes with two end guards
10/03 • 100571
600 mm Products
133
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Digital Cross-Connect System
Bay Hardware and Accessories
Rack Installation Kit
This rack installation kit comes with all the necessary hardware to install the DSX rack in a raised
floor environment.
AC Outlet Kit
This AC outlet kit is a universal continental Europe outlet that mounts in the base of the frame.
Description
Zone 2 raised floor mounting kit
Concrete floor kit
Catalog Number
RAC-MX0615
RAC-MX0616
Ordering Information
Description
UK AC outlet kit
Continental Europe AC outlet kit
North American AC outlet kit
Catalog Number
AUX-AC0003
AUX-AC0004

AUX-AC0005
Ordering Information
Note: See installation guidelines for instructions on mounting the DSX Frame.
Cross Aisle Panels
Description
128-circuit cross aisle panel
64-circuit cross aisle panel with trace LEDs
Catalog Number
AUX-200022
AUX-200064
Ordering Information
Alarm Panels
Description
64-circuit all front access panel
Catalog Number
AUX-000040
Ordering Information
10/03 • 100571
600 mm Products
134
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Features and Benefits
One part number
ADC’s Super High Density (SHD) Bay comes preassembled to the customer’s specification,
eliminating multiple parts and lineup hardware. This reduces installation time, simplifies ordering,
and helps generate revenue faster by turning up service sooner.
Waterfall IN/OUT cabling
Waterfall cabling increases lineup density, thereby saving valuable floor space and reducing cost
by eliminating the need for bay spacers.
600 mm width

The bay’s width aligns perfectly with raised floor tile dimensions, simplifying office engineering
and planning.
Integrated trouble-free cross-connect cable management
Providing increased jumper capacity, ADC’s patented cable management system eases operations
and maintenance by reducing cross-connect jumper congestion.
Expanded labeling space
Decreases possibility of mistakes during troubleshooting as all circuits are clearly identified.
64-position panels
Panel termination count matches digital switch and fiber optic multiplexer 2 Mbps signal groups
for simplified network engineering.
1152 wire-wrap or 768 BNC terminations
Industry's highest DSX density improves profitability by conserving valuable floor space.
Helps providers realize more revenue and have more space for other revenue-generating
network equipment.
192 cross aisle tie circuit
Integrated cross aisle tie panels ensure ability to add new lineups without sacrificing overall
termination density.
Single or dual bantam monitor ports
Streamlines installation, maintenance and troubleshooting. Supports traditional monitoring
practices as well as monitoring on OUT (Tx) and IN (Rx) ports of the DSX.
Overhead and raised floor cabling
Provides flexibility for any installation criteria.
2 Mbps Super High Density Solutions
DSX600
™
Bay
ADC introduces the 600 mm Super High Density Bay (SHD) product line. Quick to install, easy
to manage and maintain, Super High Density Bays maximize the network’s termination density,
simplifies engineering and is designed to match any application. Perfectly. ADC’s 600 mm Super
High Density DSX – ensuring transparent service evolution.

10/03 • 100571
600 mm Products
135
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Super High Density Solutions
DSX600
™
Bay
1
ADC’s Super High Density Bay (SHD) comes
preassembled to customer specification,
eliminating multiple parts and lineup
hardware. This reduces installation time,
simplifies ordering and saves money.
600 mm
600 mm
3
Waterfall cabling increases lineup density,
thereby saving valuable floor space and
reducing cost by eliminating the need for
costly bay spacers.
2
With its 600 mm width, ADC’s SHD
bay aligns perfectly with raised floor
tile dimensions simplifying office
engineering and planning.
By providing increased jumper capacity
(a), ADC’s patented cable management
system (b) eases operations and
maintenance by reducing cross-connect

jumper congestion. This makes removal
of inactive jumpers easy.
a
b
4
10/03 • 100571
600 mm Products
136
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Labeling is critical to troubleshooting efforts.
ADC’s SHD Bay allows technicians to clearly
identify each circuit by providing expanded
labeling space to improve network
documentation and decrease the potential
for mistakes while troubleshooting.
The SHD Bay utilizes 64-termination panels
to match digital switch and fiber optic
multiplexer two megabit signal groups,
simplifying network engineering.
With (1152) 2 Mbps terminations and 192
cross aisle terminations, ADC’s SHD Bay
provides the industry's highest DSX density
available, saving money by conserving
valuable floor space. In situations where
75 Ohm terminations are required, ADC
provides a 768 termination bay which fits in
the same lineup as the 120 Ohm bay and
maintains the advantage of ADC’s patented
cross-connect jumper management.
5

6
7
5
5
2 Mbps Super High Density Solutions
DSX600
™
Bay
5
10/03 • 100571
600 mm Products
137
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Super High Density Solutions
DSX600
™
Bay
Description
2.13 m
1152 2 Mbps terminations
192 cross aisle tie circuits
Wire-wrap OUT/IN interface
Wire-wrap cross-connect interface
Designed for below floor cabling
768 2 Mbps terminations
75 Ohm BNC OUT/IN interface
Wire-wrap cross-connect interface
Designed for below floor cabling
Super High Density Bay end guard
2.2 m

1152 2 Mbps terminations
64 cross aisle tie circuits
Dual monitor panels
32 interbay circuits
Designed for below floor cabling
1152 2 Mbps terminations
192 cross aisle tie circuits
Wire-wrap OUT/IN interface
Wire-wrap cross-connect interface
Designed for overhead cabling
1344 2 Mbps terminations
120 Ohm BNC OUT/IN interface
Wire-wrap cross-connect interface
Designed for below floor cabling
Super High Density Bay end guard
Super High Density Bay raised floor
installation kit (for 600 mm floors)
Super High Density Bay raised floor
installation kit (for 850 mm floors)
Concrete floor installation kit
Dimensions (HxWxD)
2.13 m x 600 mm x 457 mm
2.13 m x 600 mm x 457 mm
2.2 m x 600 mm x 457 mm
2.2 m x 600 mm x 457 mm
2.2 m x 600 mm x 457 mm
Catalog Number
SHD-0323
SHD-0424
SHD-0007

SHD-W-0001
SHD-0512
SHD-0051
SHD-W-0005
SHD-HR-28
SHD-HR-55
RINST-FLR
Ordering Information
Super High Density Bay
Front View
Super High Density Bay
Rear View
(Note: This application shows overhead cabling. This configuration is available upon request.)
10/03 • 100571
600 mm Products
138
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Super High Density Solutions
FlexDSX
™
Super High Density Bay
Introduction
ADC’s FlexDSX
™
Super High Density Bay offers greater termination density as well as built-in, trouble-free
cable management for flexible network planning, installation and maintenance.
ADC’s FlexDSX Super High Density Bay design is unmatched in the marketplace. ADC’s vertical IN/OUT
terminal blocks with extra cabling space and cable management fanning strips provide 50 percent more
cabling space than traditional high-density bays. Simultaneously, it provides increased jumper capacity to
simplify cross-connect wire management for easy operation and maintenance. The FlexDSX Super High

Density design incorporates a recessed vertical wireway for cross-connect cabling and up to seven
horizontal cross-connect jumper wireways instead of the standard two wireways. Vertical and horizontal
wireways are on separate planes to avoid congestion and pile-up at intersections.
The FlexDSX Super High Density Bay enables service providers to realize additional cost savings by
conserving valuable floor space. The bay provides more than 30 percent floor space savings, while
doubling the density and provides dual monitoring with ADC’s reliable FlexDSX jack technology.
Description
The FlexDSX Super High Density Bay achieves greater density in a 7-foot height x 26-inch width x 18-inch
depth, accommodating up to 1512 (7') usable DSX jack terminations. ADC’s flexible ordering guide
allows bay designs in 64 or 84 jacks per panel. This eliminates jack waste or complications in circuit
management administration.
• Provides clear identification of each circuit by offering expanded labeling space improving network
documentation and decreasing potential mistakes while troubleshooting
• Colored cross-connect labels allow for easy determination of circuit terminations
• Flashing LED and Dual monitoring
• Block’s design provides better cable management and more
space for cables
• Cable entry is allowed on both sides of block
10/03 • 100571
600 mm Products
139
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
• 1512 jacks per seven-foot bay uses an efficient jack count of
84 jacks per panel. Dual monitoring of the out and in ports,
panel termination count matches digital switching broadband
equipment for simplified network engineering. Consists of 18
panels of 84 jacks in a single plane.
• More than 30 percent floor space savings – the industry’s
highest DSX density improves profitability by conserving
valuable floor space. Service providers can realize more

revenue and more space for other revenue generating
network equipment.
• Incorporating vertical IN/OUT terminal blocks with extra
cabling space and cable management strips provide 50
percent more cabling space than traditional high-density
bays. Increased lineup density saves valuable floor space and
reduces costs by eliminating the need for bay spacers. Dual
hinged doors with designation labels on both sides provide
double the designation space. Adhesive backed labels
guarantee the identification designations will always be
available. The expanded label space minimizes the possibility
of mistakes during trouble shooting as all circuits are clearly
identified.
• Built-in trouble-free cross-connect cable management
provides increased jumper capacity. ADC’s cable management
system eases operations and maintenance by reducing cross-
connect jumper congestion and pileup.
• Tie pair terminal blocks (2) 80 circuits wired point-to-point to
tie pair blocks in the rear cross-connect field by ADC. Built-in
aisle tie panels ensure ability to grow new lineups without
sacrificing overall termination density.
• The rear cross-connect high density design allows for all jack
maintenance activities to remain at an arm’s length.
• Guarantees a worry-free maintenance environment with over
40 years of proven jack quality and reliability and a lifetime
warranty. All components of the bay are made by ADC,
ensuring quality from beginning to end.
2 Mbps Super High Density Solutions
FlexDSX
™

Super High Density Bay
Super High Density Bay
Description
*Overhead cabling denotes the cable enters the top of the bay and the equipment termination blocks are at
the top of the bay. Raised floor cabling denotes the cable enters from the raised floor into the bottom of the
bay and the equipment blocks are at the bottom of the bay.
Catalog
Number
DFX-SHD001
DFX-SHD002
DFX-SHD003
DFX-SHD004
DFX-SHD005
DFX-SHD006
# of
Terminations
1512
1512
1260
1260
1152
960
# of Cross
Aisle Circuits
160
160
160
160
160
160

Jack
Position
84
84
84
84
64
64
Description
7' concentration bay, overhead cabling
7' maintenance bay, overhead cabling
7' maintenance bay, raised Floor cabling
7' concentration bay, raised Floor cabling
2.2m concentration bay, overhead cabling
2.2m maintenance bay, overhead cabling
Ordering Information
10/03 • 100571
600 mm Products
140
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Super High Density Solutions
FlexDSX
™
Super High Density Bay
Accessories
Catalog Number
ACOK-PWNB
SHD-HR-85
SHD-HR-92
SHD-HR-43N

SHD-HR-44N
SHD-HR-91
RINST-FLR
SHD-HR-93
Description
AC outlet kit (FlexDSX Super High Density Bays
accept outlet kits in front only, North American)
End guards
7' height x 18.75" width
2.2 m height x 18" width, 600mm rack SHD
Installation kits
7' to 9' extension rack
7' to 11.5' extension rack
Installation kit, raised floor
Installation kit, concrete floor, overhead cabling
Installation kit, raised floor, metric
Ordering Information
10/03 • 100571
600 mm Products
141
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
Catalog Number
PJ712
PJ713
PJ714
PJ715
PJ716
PJ718
PJ720
PJ722

PJ1208
PJ1210
PJ1212
PJ1415
PJ1420
PJ1425
PJ1430
PJ1450
PJ762
PJ764
PJ765
PJ766
PJ768
PJ770
PJ772
PJ1308
PJ1310
PJ1312
PJ1514
PJ1520
PJ1525
PJ1530
PJ1535
PJ1545
ACK-INTL
ACK-INTL-N
Ordering Information
Description
Three conductor*
Single

1' (.3 m)
1.5' (.46 m)
2' (.61 m)
2.5' (.76 m)
3' (.91 m)
4' (1.22 m)
5' (1.52 m)
6' (1.83 m)
8' (2.44 m)
10' (3.05 m)
12' (3.66 m)
15' (4.57 m)
20' (6.1 m)
25' (7.62 m)
30' (9.15 m)
50' (15.24 m)
Dual*
1' (.3 m)
2' (.61 m)
2.5' (.76 m)
3' (.91 m)
4' (1.22 m)
5' (1.52 m)
6' (1.83 m)
8' (2.44 m)
10' (3.05 m)
12' (2.66 m)
14' (4.27 m)
20' (6.1 m)
25' (7.62 m)

30' (9.15 m)
35' (10.68 m)
45' (13.73 m)
Patch cord kit
International patch cords kit
International patch cords kit, nickel-plated
* For nickel plated patch cords, add the suffix “N”. For plenum-rated fire
retardant patch cords, add the suffix “PL”.
2 Mbps Super High Density Solutions
Accessories
Bantam Patch Cords
PJ768
Three-Conductor Dual Patch Cord
PJ718
Three-Conductor Single Patch Cord
10/03 • 100571
600 mm Products
142
www.adc.com • +32-2-712-65-00 • +32-2-712-65-42
2 Mbps Super High Density Solutions
Accessories
Description Catalog Number
Ordering Information
Tools and Tool Kits
Description
Cross-connect wire, 500-foot roll (150 m)
Cross-connect wire, 1000-foot roll (300 m)
Cross-connect wire, 1500-foot roll (450 m)
Cross-connect wire, 2000-foot roll (600 m)
Catalog Number

DSX-CCW/500
DSX-CCW/1000
DSX-CCW/1500
DSX-CCW/2000
Ordering Information
Cross-Connect Wire
Manual wire-wrap kit includes: AUX-0X0165
Manual wire-wrap kit
22-24 AWG wire-wrap bit sleeve
24-26 AWG wire-wrap bit sleeve
22-24 AWG wire-wrap bit
26 AWG wire-wrap bit
Mannual wire-cutting/stripping tool AUX-0X0803
Manual unwrapping tool (screw driver tool) AUX-0X0802
Manual unwrapping tool (soft, ergonomic handle) AUX-0X0381
Unwrapping sleeve for use with AUX-0X0381 AUX-0X0383
Electric 220 wire-wrap gun AUX-0X0466
22-24 AWG bit (0.64 - 0.51mm) AUX-0X0467
22-24 AWG sleeve (0.64 - 0.51mm) AUX-0X0468