Bsi bs en 00716 1 2008 + a1 2013

BRITISH STANDARD

BS EN
EN
716-1:2008
716-1:2008

+A1:2013
Incorporating
corrigendum
June 2013

Furniture — Children’s
cots and folding cots for
domestic use —
Part 1: Safety requirements

ICS 97.140; 97.190






















BS

BS EN
EN 716-1:2008
716-1:2008+A1:2013

National foreword
This British
British Standard
Standard is
is the
the UK
UK implementation
implementation of
of EN
EN 716-1:2008+A1:2013.
716-1:2008. It
This
supersedes
BSBS
7423:1999
and BS which
EN 716-1:1996,
which are withdrawn.
It
supersedes
EN 716-1:2008,
is withdrawn.
BSI,UK
as aparticipation
member
of CEN,

obliged
to publish
EN 716-1
asTechnical
a British
Standard.
in itsispreparation
was provided
entrusted
Committee
The
CEN
Correction
Notice
20 March
2013
a by
revised
English
However,
attention
drawn
thecare
fact
that
the development
of this
CW/1,
Safety
ofChanges

childisuse
and to
child
to Subcommittee
language
text.
implemented
byproducts,
this during
Correction
Notice areCW/1/5,
listed
after
European
Standard, the UK committee voted against its approval as a
Nursery
the
CENfurniture.
foreword.
European Standard.
A listUK
of organizations
represented
on this
be obtained
on
The
participation in
its preparation
wassubcommittee

entrusted by can
Technical
Committee
The reason
forof
this
disapproval
wascare
that,
in the opinion
of the UK Committee,
request
to its
secretary.
CW/1,
Safety
child
use and child
products,
to Subcommittee
CW/1/5,
BS EN 716-1
does not address the safety issues related to the interaction of
Nursery
furniture.
The
doesmight
not purport
to include
all the necessary

provisions
of aIn
otherpublication
products that
be supplied
and intended
to be attached
to cots.
contract.
Users are responsible
for its
correct
application.can be obtained on
A
list
of
organizations
represented
on
this
subcommittee
these instances, an additional risk assessment should be undertaken.
request
to its secretary.
Compliance
with a British Standard cannot confer immunity from
The UK participation in its preparation was entrusted to Technical Committee
legalpublication
obligations.
The

does
purport
to include all the necessary provisions of a
CW/41, Child use
andnot
care
articles.
contract. Users are responsible for its correct application.
A list of organizations represented on this committee can be obtained on
Compliance
with a British Standard cannot confer immunity from
request
to its secretary.
legal obligations.
This publication does not purport to include all the necessary provisions of a
contract. Users are responsible for its correct application.
Compliance with a British Standard cannot confer immunity from
legal obligations.

This British Standard was
published under the authority
of theBritish
Standards
Policywas
and
This
Standard
Strategy
Committee
published under the authority

onthe
31 July
2008 Policy and
of
Standards
Strategy Committee
on 31 July 2008
© The British Standards
Institution 2013.
Published by BSI Standards
Limited
2013
©
BSI 2008

ISBN
ISBN 978
978 00 580
580 57969
82818
70908 18
1

Amendments/corrigenda issued since publication
Amendments/corrigenda issued since publication
Date
Comments
Amendments/corrigenda
issued since publication
Date

Comments
Date
Comments
28 February 2013
Implementation of CEN amendment A1:2013
28 February 2013
Implementation of CEN amendment A1:2013
30 June 2013
Implementation of CEN Correction Notice
20 March 2013


EUROPEAN STANDARD

EN 716-1:2008+A1

NORME EUROPÉENNE
EUROPÄISCHE NORM

January 2013

ICS 97.140

Supersedes EN 716-1:2008

English Version

Furniture - Children's cots and folding cots for domestic use Part 1: Safety requirements
Meubles - Lits à nacelle fixes et pliants à usage domestique
pour enfants - Partie 1 : Exigences de sécurité

Möbel - Kinderbetten und Reisekinderbetten für den
Wohnbereich - Teil 1: Sicherheitstechnische Anforderungen

This European Standard was approved by CEN on 2 February 2008 and includes Amendment 1 approved by CEN on 17 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2013 CEN

All rights of exploitation in any form and by any means reserved
worldwide for CEN national Members.

Ref. No. EN 716-1:2008+A1:2013: E

BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

Contents

Page

Foreword .......................................................................................................................................................3
1

Scope ................................................................................................................................................4

2

Normative references .......................................................................................................................4

3

Terms and definitions ......................................................................................................................4

4
4.1
4.2
4.2.1
4.2.2
4.3

4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
4.4.8
4.4.9
4.5
4.6

Safety requirements .........................................................................................................................5
General .............................................................................................................................................5
Materials ...........................................................................................................................................5
Materials and surfaces .....................................................................................................................5
Flammability of textiles, coated textiles and plastics coverings ................................................... 5
!Initial stability" .........................................................................................................................5
Construction.....................................................................................................................................5
General .............................................................................................................................................5
Holes, gaps and openings on the inside of the cot ........................................................................ 6
Head entrapment on the outside of the cot..................................................................................... 7
Shear and squeeze points ...............................................................................................................7
Snag points ......................................................................................................................................7
Locking systems ..............................................................................................................................7
Cot base............................................................................................................................................8
Sides and ends .................................................................................................................................8
Cot rim ..............................................................................................................................................9
Final stability ....................................................................................................................................9

!Mattress size" ..........................................................................................................................9

5

Packaging .........................................................................................................................................9

6

Instructions for use ........................................................................................................................ 10

7

Marking ........................................................................................................................................... 11

Annex A (informative) !A–deviations"................................................................................................. 12

2


EN 716-1:2008+A1:2013 (E)
BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

Foreword
Foreword

This document (EN 716-1:2008+A1:2013) has been prepared by Technical Committee CEN/TC 207
“Furniture”,
the secretariat
of which is held by UNI.
This
document
(EN 716-1:2008+A1:2013)
has been prepared by Technical Committee CEN/TC 207
“Furniture”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text
by endorsement,
the latest
by July
2013, and
national standards
shall be withdrawn
at the
Thisor
European
Standardatshall
be given
the status
of a conflicting
national standard,
either by publication
of an identical
latest
by
July

2013.
text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the
latest by July 2013.
Reference:
EN 716:2008+A1:2013
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
Furniture
- Children's
cots
and
cots
for domestic
use
Part 1:
Safety
rights.
[and/or
shall
not
befolding
held
forofidentifying
any
ormay
allrequirements
such
patent
rights.
Title: CEN
Attention

is drawn
toCENELEC]
the
possibility
that
some
ofresponsible
the elements
this- document
be the
subject
of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
00207237
Workdocument
Item:
This
supersedes !EN 716-1:2008."
This document supersedes !EN 716-1:2008."
Brussels,
This document includes Amendment 1 approved by CEN on 17 November
2012 2013-03-20
Thisreference
documenttoincludes
Amendment
1 approved
by CEN
on 17
November
2012 in the document related to:

With
the above,
please include
the following
minor
editorial
correction(s)
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
the following language version(s) :
According
to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
English
countriesFrench
are
bound
to implement this
European
Standard:
Bulgaria,
Croatia,ofCyprus,
Czech
According
to the
CEN/CENELEC
Internal
Regulations,
theAustria,
nationalBelgium,
standards

organisations
the following
Republic,
Denmark,
Estonia,
Finland,
Former
Yugoslav
Republic
of
Macedonia,
France,
Germany,
Greece,
countriesGerman
are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Hungary,
Ireland,
Italy,Finland,
Latvia, Former
Lithuania,
Luxembourg,
Malta,
Netherlands,France,
Norway,Germany,
Poland, Portugal,
Republic, Iceland,
Denmark,
Estonia,
Yugoslav

Republic
of Macedonia,
Greece,
for the following
procedure
:Italy,
Romania,
Slovakia,
Slovenia,
Spain,
Sweden,
Switzerland,
Turkey
andNetherlands,
the United Kingdom.
Hungary,
Iceland,
Ireland,
Latvia,
Lithuania,
Luxembourg,
Malta,
Norway, Poland, Portugal,
Romania,Publication
Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

Correction Notice

FJD
CEN

Correction Notice 20 March 2013

Correction
20that
March
2013 provided
a revised
English
text, incorporating
ItThe
has CEN
been brought
to ourNotice
attention
this document,
issued on
2013-01-09
(CEN language
Standards Publications
Weekly Output
Reference
2013/01/I)
requires
modification.
the following
editorial
corrections:

Please find enclosed the updated English version.

We apologise for any inconvenience this may cause.

3
3


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

1

Scope

This part of EN 716 specifies safety requirements for children's cots for domestic use with an internal length
greater than 900 mm but not more than 1 400 mm.
The requirements apply to a cot that is fully assembled and ready for use.
Cots that can be converted into other items e.g. changing units, playpens should, when converted, comply
with the relevant European standard for that item.
This standard does not apply to carry cots, cribs and cradles for which a separate European standard exists.

2

Normative references

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.
EN 71-1, Safety of toys — Part 1: Mechanical and physical properties
EN 71-2:2006, Safety of toys — Part 2: Flammability
EN 71-3, Safety of toys — Part 3: Migration of certain elements
!EN 716-2:2008+A1:2013", Children's cots and folding cots for domestic use — Part 2: Test methods
EN 1103, Textiles - Fabrics for apparel - Detailed procedure to determine the burning behaviour

3

Terms and definitions

For the purposes of this European Standard, the following terms and definitions apply.
3.1
folding cot
cot which can be dismantled or folded without the use of a tool for transportation. This does not include items
such as carry cots intended for transportation of infants
NOTE

In some countries "folding cots" are also called "travel cots".

3.2
locking system
mechanism consisting of a locking device and one or more operating devices, which can deactivate the
locking device, e.g. by pushing a button, pressing a lever or turning a knob
3.3
locking device
device intended to maintain the cot or parts of it in its intended position
3.4
shear and squeeze points
gaps which can cause harm to parts of the body and which occur when two accessible parts move relative to

each other

4


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

3.5
accessible parts
!when a child’s hand can neither reach through sides nor ends, the inside of the cot and the exterior of the
cot 300 mm from the upper part of the rim
when a child’s hand can reach through sides or ends, accessible parts are the whole cot except the underside
of the cot base"
3.6
mattress base
cot base and mattress combined in one component
3.7
movable sides
sliding sides, drop sides, folding sides, etc

4

Safety requirements

4.1

General

With the exception of the requirements specified in clause 4.2, the requirements apply both before and after
testing in accordance with !EN 716-2:2008+A1:2013".

4.2

Materials

4.2.1

Materials and surfaces

The manufacturer/importer/retailer shall provide verification that all accessible parts meet the relevant
requirements from EN 71-3.
4.2.2

Flammability of textiles, coated textiles and plastics coverings

When tested in accordance with 5.4 of EN 71-2:2006, the maximum rate of spread of flame of textiles, coated
textiles or plastic coverings shall be 30 mm/s.
When tested in accordance with EN 1103, there shall be no flash-effect.
!

4.3

Initial stability

When tested in accordance with 5.2 of EN 716-2:2008+A1:2013, the cot shall not overturn."

4.4

Construction

4.4.1
4.4.1.1

General
Edges and protruding parts

Edges and protruding parts accessible during normal use shall be rounded or chamfered and free of burrs and
sharp edges.

5


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)
4.4.1.2

Self-tapping screws

Self-tapping screws shall not be used to fasten any component that is designed to be removed or loosened
when dismantling the cot for purposes of transportation or storage.
NOTE

Self-tapping screws include wood screws, particleboard screws and the like.

4.4.1.3

Labels and decals

!Glued labels and decals shall not be used on the internal surfaces of cot sides and ends unless they are
below the level of the cot base or mattress base."
4.4.1.4

Small parts

When tested in accordance with !5.5" of !EN 716-2:2008+A1:2013", no accessible part that can be
detached shall fit wholly within the small parts cylinder.
4.4.1.5

Castors and wheels

Castors/wheels shall not be fitted except in the following configuration, either:
a)

two or more castors/wheels and at least two other support points, or,

b)

at least four castors/wheels, of which at least two can be locked.

4.4.2
4.4.2.1

Holes, gaps and openings on the inside of the cot
General

With the exception of the holes, gaps and openings specified in !4.4.2.2, 4.4.2.3, 4.4.2.4, 4.4.2.5, 4.4.2.6,
4.4.4.2 and 4.4.4.3" all other accessible holes, gaps and openings shall be less than 7 mm, between 12 mm
and 25 mm, or between 45 mm and 65 mm when tested in accordance with !5.4.1" of !EN 7162:2008+A1:2013".
4.4.2.2

Assembly holes

There shall be no accessible holes between 7 mm diameter and 12 mm diameter, unless the depth is less
than 10 mm.
4.4.2.3

Distance between cot base and sides and ends

When tested in accordance with !5.4.1" of !EN 716-2:2008+A1:2013", it shall not be possible for the
25 mm cone to pass between the cot base and the sides, and between the cot base and the ends.
4.4.2.4

Openings in mesh sides and ends

When the sides or ends are of mesh, it shall not be possible for the 7 mm cone as described in !5.4.1"
of !EN 716-2:2008+A1:2013" to pass through the holes of the mesh.
4.4.2.5

Distance between slats of the cot base

When tested in accordance with !5.4.1" of !EN 716-2:2008+A1:2013", it shall not be possible for the

60 mm cone to pass between two adjacent slats of the cot base.

6


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)
4.4.2.6

Openings in mesh of the cot base

When tested in accordance with !5.4.1" of !EN 716-2:2008+A1:2013", it shall not be possible for the
85 mm cone to pass through a cot base made of mesh.
4.4.3

Head entrapment on the outside of the cot

!The following requirements do not apply to cots that have mesh or fabric sides/ends and a rigid leg or
support system, when the lowest part of the opening is less than 100 mm from the floor."
When tested in accordance with !5.4.2" of !EN 716-2:2008+A1:2013", completely bound openings
on the outside (exterior) of the cot that allow passage of the small head probe, shall also allow the large head
probe to pass completely through the bound opening.
Completely bound openings that allow the large probe to pass completely through shall comply with the
requirement for partially bound, V and irregular shaped openings when tested in accordance with !5.4.2"
of !EN 716-2:2008+A1:2013".
Partially bound, V and irregular shaped openings shall be constructed so that:

a) portion B of the template does not enter the opening when tested in accordance with !5.4.2"
of !EN 716-2:2008+A1:2013"; or
b) apex of portion A of the template contacts the base of the opening when tested in accordance
with !5.4.2" of !EN 716-2:2008+A1:2013".
4.4.4
4.4.4.1

Shear and squeeze points
Shear and squeeze points when setting up and folding

If !4.4.4.2 or 4.4.4.3" are not applicable, shear and squeeze points that are created only when setting up
or folding are permitted.
4.4.4.2

Shear and squeeze points under the influence of powered mechanisms

Where powered or spring loaded mechanisms are used, the distance between two accessible parts moving
relative to each other shall always be greater than 18 mm or smaller than 5 mm.
4.4.4.3

Shear and squeeze points during use

There shall be no accessible shear and squeeze points which close to less than 18 mm unless they are
always less than 5 mm during the last load application according to !5.9.1" of !EN 7162:2008+A1:2013".
4.4.5

Snag points

When tested in accordance with !5.10" of !EN 716-2:2008+A1:2013", the mass shall not be
supported by any part accessible from inside the cot. Parts of cot sides and ends more than 1 400 mm above

the cot base are considered not accessible.
4.4.6
4.4.6.1

Locking systems
Locking systems for folding cots

Folding cots that fold towards the inside shall be equipped with at least two locking systems fulfilling the
requirements of !4.4.6.2."

7


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)
In order to prevent a folding cot from folding unintentionally, all other folding cots shall be equipped with a
locking system fulfilling the requirements of !4.4.6.2."
The cot shall not fold and the locking system shall fulfil its function when tested in accordance with 5.11
of !EN 716-2:2008+A1:2013".
4.4.6.2

All locking systems

With the exception of the locks on castors/wheels, all locking systems shall:
a)

have a residual force of at least 50 N (tangential when relevant) for operation when tested in accordance
with 5.11 of !EN 716-2:2008+A1:2013"; or

b)

require at least two consecutive actions operating on different principles, the second being dependent on
the first having been carried out and maintained; or

c)

require at least two separate but simultaneous actions operating on different principles; or

d)

have two operating devices separated by a distance of at least 850 mm and required to be operated
simultaneously; or

e)

require the cot base to be lifted to allow folding of the cot.

If the weight of the child on the cot base has a positive effect on the locking, this is accepted as an operating
device.
The locking system shall fulfil its function before and after testing in accordance with 5.11 of !EN 7162:2008+A1:2013".
4.4.7

Cot base

!
4.4.7.1

Folding mattress base and cot base

Any folding mattress base or cot base shall not fold when tested in accordance with 5.7 of EN 7162:2008+A1:2013 (folding test of the mattress base and cot base)."
4.4.7.2

Adjustable cot base

If the cot base is adjustable, adjustment from a higher position to a lower position shall require the use of a
tool or operation of a locking system, which fulfils the requirements of !4.4.6.2."
4.4.7.3

Strength of the cot base

When tested in accordance with !5.7.2" of !EN 716-2:2008+A1:2013", no element of the cot base
shall break, nor shall the cot base become dislodged and the function of the cot shall not be impaired.
4.4.8
4.4.8.1

Sides and ends
Movable sides

!Movable sides shall be provided with a locking system fulfilling the requirements of 4.4.6.2. The locking
system shall engage automatically when the movable side is in the open and closed position."

8


BS
716-1:2008+A1:2013

EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)
4.4.8.2

Distance between footholds and top of cot sides and ends

When tested in accordance with !5.9.1" of !EN 716-2:2008+A1:2013", under load, the distance
between the upper side of the cot base/mattress base and the upper edge of the cot side and end shall be at
least 600 mm.
When tested in accordance with !5.3.3" of !EN 716-2:2008+A1:2013", there shall be a distance of at
least 600 mm between the top of any foothold and the top of the cot side and end.
With the cot base and the sides/ends in the highest position, the distance between the upper side of the cot
base and the upper edge of the cot side and end shall be at least 300 mm, measured from the lowest point of
the side and end.
4.4.8.3

Strength of side and end components

When tested in accordance with !5.8.1, 5.8.2 and 5.8.3" of !EN 716-2:2008+A1:2013", the slats or
sides and ends and corners shall neither break nor become detached. The function of the cot shall not be
impaired.
When tested in accordance with !5.8.4" of !EN 716-2:2008+A1:2013", the threads of the mesh and
other flexible materials, e.g. fabrics, plastics shall not break and the function of the cot shall not be impaired.
4.4.8.4

Strength of frame and fastenings

When tested in accordance with !5.9.1 and 5.9.2" of !EN 716-2:2008+A1:2013", there shall be no

breakage. The function of the cot shall not be impaired.
The test in !5.9.2" of !EN 716-2:2008+A1:2013" is not applicable to folding cots.
4.4.9

Cot rim

No filling shall be removed from the cot rim when tested in accordance with !5.6, bite test", of !EN 7162:2008+A1:2013".
!deleted text"
!

4.5

Final stability

When tested in accordance with 5.12 of EN 716-2:2008+A1:2013, the cot shall not overturn."

!
4.6

Mattress size

If a mattress is supplied with the cot, the dimensions of the mattress shall be as specified in Clause 6 l)."

5

Packaging

Any plastic covering used as packaging for cots, folding cots or mattresses, if applicable, that does not fulfil
the requirements of EN 71-1, shall be conspicuously marked with the following information or its equivalent:
"To avoid danger of suffocation keep this plastic bag away from babies and children."

9


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

6

Instructions for use

Instructions shall be provided in the official language(s) of the country where the cot is sold.
These instructions shall be headed "IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ
CAREFULLY" in letters not less than 5 mm high.
Warnings
The instructions for use shall include the following warnings:
a)

Warning: Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the cot.

b)

Warning: Do not use the cot if any part is broken, torn or missing and use only spare parts approved by
the manufacturer.

c)

Warning: Do not leave anything in the cot or place the cot close to another product, which could provide a
foothold or present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.

d)

Warning: Do not use more than one mattress in the cot.

The instructions for use shall include the following statements:
e)

Statement that a cot is ready for use, only when the locking mechanisms are engaged and to check
carefully that they are fully engaged before using the folding cot.

f)

If the height of the cot base is adjustable, a statement that the lowest position is the safest and that the
base should always be used in that position as soon as the baby is old enough to sit up.

g)

When movable sides are provided, a statement that "if you leave the child unattended in the cot, always
make sure that the movable side is closed".

h)

Where detachable support rails are provided to support the cot base above its lowest position, a
statement that it is essential to remove these rails before the cot is used in its lowest position.

i)

Assembly drawing, a list and description of all parts and tools required for assembly and a diagram of the
bolts and other fastenings required.

j)

Thickness of the mattress shall be such that the internal height (surface of the mattress to the upper edge
of the cot frame) is at least 500 mm in the lowest position of the cot base and at least 200 mm in the
highest position of the cot base.

k)

Where the requirement in 6 j) is fulfilled by a mark on the cot, a statement that the mark indicates the
maximum thickness of the mattress to be used with the cot.

l)

Statement about the minimum size of mattress to be used with the cot. The length and width shall be
such that the gap between the mattress and the sides and ends does not exceed 30 mm.

m) Statement that all assembly fittings should always be tightened properly and that fittings should be
checked regularly and retightened as necessary.
n)

Instructions for washing/cleaning, when applicable.

o)

Statement to prevent injury from falls that when the child is able to climb out of the cot, the cot shall no

longer be used for that child.

10


BS
716-1:2008+A1:2013
EN EN
716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

7

Marking

All cots for which a claim of conformity to this standard is made shall be permanently marked with the
following information:
a) name, registered trade name or registered trade mark of either the manufacturer or distributor or retailer
together with additional means of identifying the product;
b) reference to this EN (!EN 716-1:2008+A1:2013");
c) if the mattress is not an integral part of the cot, the maximum thickness of the mattress to be used. This
can be in the form of text, a distinct mark on the cot at the correct height, e.g. a line, or by other means.

11


BS
716-1:2008+A1:2013
EN EN

716-1:2008+A1:2013
(E)
EN 716-1:2008+A1:2013 (E)

Annex A
(informative)
!A–deviations

A-deviation: National deviation due to regulations, the alteration of which is for the time being outside the
competence of the CEN/CENELEC member.
This European Standard does not fall under any Directive of the EU. In the relevant CEN/CENELEC countries
these A-deviations are valid instead of the provisions of the European Standard until they have been removed.
SWEDEN
Clause

Deviation

4.4.2.5

Children’s cots provided on the Swedish market shall
have a distance < 25 mm between two adjacent slats
of the cot base. When tested in accordance with
5.4.1 of EN 716-2 + A1: 2013, it shall not be possible
for the 25 mm cone to pass between two adjacent
slats of the cot base.
This is the interpretation of the Swedish Product
Safety Act made by the Swedish Market Court in two
court cases: MD 1991:30 and MD 2005:15.

"

12


blank


British Standards Institution (BSI)
BSI is the independent national body responsible for preparing British Standards and other
standards-related publications, information and services. It presents the UK view on standards
in Europe and at the international level.
BSI is incorporated by Royal Charter . British Standards and other standardization
products are published by BSI Standards Limited .

Revisions

Information on standards

British Standards and PASs are periodically updated by amendment or
revision. Users of British Standards and PASs should make sure that they
possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and
services. We would be grateful if anyone finding an inaccuracy or ambiguity
while using British Standards would inform the Secretary of the technical
committee responsible, the identity of which can be found on the inside front
cover. Similary for PASs, please notify BSI Customer Services.
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001

BSI provides a wide range of information on national,
European and international standards through its Knowledge

Centre.

BSI offers BSI Subscribing Members an individual updating service called
PLUS which ensures that subscribers automatically receive the latest editions
of British Standards and PASs.

Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001
Email:

Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001
Email:

Information regarding online access to British Standards and
PASs via British Standards Online can be found at
www.bsigroup.com/BSOL
Further information about British Standards is available on the BSI
website at www.bsigroup.com/standards

Buying standards
You may buy PDF and hard copy versions of standards directly using a
credit card from the BSI Shop on the website www.bsigroup.com/shop.
In addition all orders for BSI, international and foreign standards publications
can be addressed to BSI Customer Services.
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001
Email:
In response to orders for international standards, BSI will supply the British
Standard implementation of the relevant international standard, unless
otherwise requested.

Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005

Email:
BSI Subscribing Members are kept up to date with standards
developments and receive substantial discounts on the purchase price
of standards. For details of these and other benefits contact Membership
Administration.

Copyright
All the data, software and documentation set out in all British Standards
and other BSI publications are the property of and copyrighted by BSI,
or some person or entity that owns copyright in the information used
(such as the international standardization bodies) has formally licensed
such information to BSI for commercial publication and use. Except as
permitted under the Copyright, Designs and Patents Act 1988 no
extract may be reproduced, stored in a retrieval system or transmitted in
any form or by any means – electronic, photocopying, recording or
otherwise – without prior written permission from BSI. This does not
preclude the free use, in the course of implementing the standard, of
necessary details such as symbols, and size, type or grade designations. If
these details are to be used for any other purpose than implementation
then the prior written permission of BSI must be obtained. Details and
advice can be obtained from the Copyright & Licensing Department.
Tel: +44 (0)20 8996 7070
Email:

BSI
389 Chiswick High Road London W4 4AL UK
Tel +44 (0)20 8996 9001
Fax +44 (0)20 8996 7001
www.bsigroup.com/standards

raising standards worldwide™