Mô hình Belem Tower, Portugal. P1

Belem Tower, Portugal : Assembly Instructions

© Canon Inc. © A&A

Before starting assembly :
Writing the number of each section on its back side before
cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after
cutting out the sections.)

h t t p : / / w w w. c a n o n . c o m / c - p a r k / e n /

Indicates where sections should
be glued together.

[1] Assemble the base.

http:

//ww

View of completed model
* This model was designed for Papercraft and may differ from the original in some respects.

Assembly Instructions : Seven A4 sheets (No. 1 to No. 7)
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.

Assembly Instructions
Mountain fold(dotted line)

Make a mountain fold.
Valley fold(dashed and dotted line)

Make a valley fold.
Scissors line(solid line)

Cut along the line.
Cut in line(solid line)

Cut along the line.

Tools and materials
Assembly tip
Caution

Glue
The glue spot(colored dot)
shows where to apply the glue.

Glue spot(Red dot)

Glue parts with the same number together.
Glue spot(Green dot)

Glue within the same part.
Glue spot(Blue dot)

Glue to the rear of the other part.

Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.

w.ca
n

on.c

om/c

-park

/en/

© A&

A

CAUTION

Do not hit other people with the pointed edges.
Doing so could result in injury.
Adults should make sure that children observe
this caution.

Belem Tower, Portugal : Assembly Instructions

© Canon Inc. © A&A

While gluing this part in place,
adjust it to make sure the sides of
the base do not bulge out.


Belem Tower, Portugal : Assembly Instructions
[2] Assemble the vents.

© Canon Inc. © A&A


Belem Tower, Portugal : Assembly Instructions

© Canon Inc. © A&A

[3] Assemble the upper part of the building.

Assemble the other parts
in the same way.
Insert this part and
glue it in place on
the rear side.

[2] Vent

Insert this part

and glue it in place
on the rear side.

Assemble the other parts
in the same way.

Insert parts
and
from
beneath part
and glue them
in place on the underside
of part
.

Assemble in
the same way
as part
.


Belem Tower, Portugal : Assembly Instructions
[4] Assemble the lower part of the building and glue the tower windows in place.
Reinforce the cutout parts
by gluing their rear sides
to each other.

[3] Upper part
of the building

© Canon Inc. © A&A

The other side of the tower


Belem Tower, Portugal : Assembly Instructions

© Canon Inc. © A&A

[5] Assemble the top level of the tower.

Attach these parts by matching
this glue point to part
.
Insert parts
,
,
and
from beneath part
and glue them in place on
the underside of part
.

[4] The building


Belem Tower, Portugal : Assembly Instructions

© Canon Inc. © A&A

[6] Glue the observation towers to the building
and glue the building to the base.
Glue these pieces in
place by inserting them
into the uneven parts
of the walls.

[5] Building
Finished!

Glue these pieces in
place by inserting
them into the uneven
parts of the walls.

[1] Base

Bele
Lisb

mT

on,

o

Port wer
ugal