HƯỚNG DẪN SỬ DỤNG LỒNG ẤM TRẺ SƠ SINH MODEL A3186

HƯỚNG DẪN SỬ DỤNG

LỒNG ẤM TRẺ SƠ SINH
MODEL A3186

OM-A3186
Revision: 04/08
Edition: 09/08


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

2.1

- LỒNG ẤP TRẺ SƠ SINH MODEL A 3186
−
−
−
−

2.1.1

−
−
−
−
−
−
−
−

2.1.2

giới thiệu
Control Zone: vùng thao tác phía trên mặt nệm
Incubator Temperature: nhiệt độ môi trường , được đo trong Control Zone.
Control Temperature: bảng điều khiển nhiệt độ, có thể điều chỉnh bởi người dùng.
Incubator Stability Condition: khi nhiệt độ không vượt quá 1,0 °C trong vòng 1 giờ.
Các chỉ số được đọc trong bảng Control Temperature of 32 °C and/or 36 °C.
Temperature Rising Time:thời gian cần thiết để lồng ấm tăng nhiệt độ lên 11°C, khi
Air Control Temperature ít hơn 12°C hoặc cao hơn nhiệt độ xung quanh.
Temperature Uniformity: nhiệt độ trung bình tại 4 điểm cách 10 cm phía trên bề mặt
nệm, nó khác với nhiệt độ trung bình của lồng ấp.
Temperature Variation: sự khác nhau giữa nhiệt độ lồng ấp và nhiệt độ trung.
Excess Temperature: khi nhiệt độ bên trong lồng ấp vượt quá nhiệt độ trung bình,khi
đó cần thay đổi lại giá trị nhiệt độ .
Measurements Points: đo tại 5 điểm song song cách 10cm phía trên mặt nệm , 1 điểm
đặt cách 10cm phía trên trung tâm mặt nệm , 4 điểm còn lại đặt 4 hướng khác nhau.
ATC: chế độ điều khiển nơi mà nhiệt độ được tự động điều khiển bởi cảm biến nhiệt
độ, được cài đặt bởi người dùng .
ITC: chế độ điều khiển nơi mà nhiệt độ không khí được điều khiển và có khả năng tự
điều khiển nhiệt độ không khí trong lồng ấp, và nó được đo bởi nhiệt độ da.
Routine Calibration: cách calib lồng ấp hoặc các chức năng khác.

- đặ tính điện
♦ điện áp
♦ tần số
♦ dòng
♦ dòng rò
♦ Inlet Power


LED panel with no optionals

LED panel with optionals

LCD panel with optionals
♦ công suất ngõ ra (Auxiliary Switches)
♦ công suất motor
♦ công suất bộ làm ấm
♦ Ergometric Support Power
♦ pin có thể sạc lại

127V~ or 220V~ or
240V~
50/60 Hz
5A -127V~ / 3A -220
and
240V~
< 100 µA
300 W
350 W
350 W
150 W (each switch)
50 W
120 W
180 W
9V

Cầu chì
Model /
Use

♦ Incubator A 3186 - 127V~

Fuse
5A–F


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

♦ Incubator A 3186 - 220V~ or 240V~
♦ Ergometric Support 127V~
♦ Ergometric Support 220V~ / 240V~
♦ 4 Auxiliary Switch Set – 127V~

Type
3A–F
Type
3A–F
Type
2A–F
Type
7A–F
Type


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

2.1.3

♦

Model /
Use
4 Auxiliary Switch Set 220V~ / 240V~

♦

6 Auxiliary Switch Set 127V~

♦

6 Auxiliary Switch Set 220V~ / 240V~

3A–F
Type
10 A – F
Type
5A–F
Type

- phân lớp điện và các đặ tính
♦
♦
♦
♦

kiểu Class
kiểu điện
bảo vệ chống nước

bảo vệ chống nổ

♦ tối đa % of CO2
♦ vận tốc khí trên mặt nệm
♦ ồn bên trong (xung quanh <45 dBA)
2.1.4

Fuse

Class I
BF Type
IPX4
Non AP / Non
APG
< 0,2%
< 0,35 m/s
< 50 dBA

- các đặc điểm của bộ điều khiển
Nhiệt độ không khí và nhiệt độ da
♦ khoảng hiển thị của nhiệt độ không khí và da
♦
♦
♦
♦
♦
♦

thang hiển thị nhiệt độ
độ chính xác

Temperature Rise Time
Excess Temperature
Temperature Uniformity
Temperature Variation

♦ khoảng điều khiển – Air Mode
♦ khoảng điều khiển – Skin Mode

17,0 – 50,0
°C
0,1ºC
± 0,2 °C
40 min
0,8ºC
< 0,6ºC
± 0,2ºC
20,0 - 39,0
°C Key >
37 °C
34,0 – 38,0
°C Key >
37 °C

Hệ thống Oxygen
♦
♦
♦
♦
♦
♦

♦

độ phân giải
khoảng hiển thị O2
khoảng điều khiển – O2
độ chính xác – O2 (định chuẩn tại 100%)
độ chính xác – O2 (định chuẩn tại 21%)
lưu lượng vào tối đa O2
calib cảm biến O2 (ServoControlled Mode)

1%
18% to 100%
21% to 65%
3%
5%
30 lpm
7 days


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

♦ calib áp lực cảm biến O2
♦ khoảng hoạt động của cảm biến
♦ kích thước ngõ vào O2

600 a 900 mm Hg
20 °C - 41 °C
Thread 9/16” –
18UNF

Hệ thống làm ấm
♦ độ phân giải hiển thị
♦ khoảng hiển thị độ ẩm
♦ khoảng điều khiển – độ ẩm tương đối
♦ độ chính xác – độ ẩm tương đối
♦ dung tích bình chứa
♦ khoảng thời gian hoạt động – dung tích tối đa
* For ambient temperature 23º+/- 1ºC and Control Temperature 34ºC

1%
20% to
100%
30 % to 95
%
±5%
950 ml
25 hrs – 80%


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

Trọng lượng trẻ - tỷ lệ
♦ Độ phân giải
♦ Trọng lượng
♦ Độ chính xác
2.1.5

0,2g

0 to 10Kg
± 0,4 g

- thong số kỹ thuật
lồng ấp trên xe đẩy

♦
♦
♦
♦
♦
♦
♦

dài
rộng
cao
chiều cao của nệm
trọng lượng có ngăn chứa và các thanh
trọng lượng không có ngăn chứa và các thanh
bánh xe có thể xoay 4” – có khóa

107 cm
56 cm
138 cm
98 cm
77 kg
65 kg
4 units

Incubator on Ergometric Support
♦ Width
♦ Depth
♦ Height (Min. and Max.)
♦ Height – Mattress Level (Min. and Max.)
♦ Weight with Rods and Shelves
♦ Weight without Rods and Shelves
♦ Rotating Wheel 4” - Brake

107 cm
56 cm
134 to 154
cm
94 to 114
cm
80 kg
68 kg
4 unit.

Dome/ Bed Specifications
♦ Oval Ports*
♦ Iris Sleeve
♦ Access Panel*
♦ Diffuser for Pipe Passage *
♦ Mattress Dimensions
♦ Mattress/ Access Panel Passage Height
♦ Mattress Elevation (Trendelenburg and Reverse)
* Variations according to dome models.
2.1.6

5 units
1 unit
Front + Rear
4 left + 4 right
34 cm x 63 cm
21 cm
± 10º

- Maximum Loads
♦
♦

Serum Support
Auxiliary Shelves

2 kg
10 kg per


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

♦

Bed

shelf
7 kg

USER’S MANUAL
A 3186 NEONATAL INCUBATOR

2.1.7

- Alarms
System Alarms
♦

Power Failure

♦

Air Circulation Failure

♦

System Failure

Actuate if power failure occurs for the Incubator or if the
power wire is accidentally disconnected from the system.
Actuated when the internal air flow is interrupted.
Performance Time after the failure up to 120 seconds.
Actuated when an internal failure occurs in the control
microprocessor.

Attention: When the incubator is turned on, the Air Circulation Failure Alarm remains
unactuated during 40 minutes, becoming active after this period is elapsed.

Attention: The temperature setting values will remain memorized.

Temperature Alarms
♦

High Temperature

♦

Low Air
Temperature

♦

High Air
Temperature
Skin Temperature
High
Skin Temperature
Low

♦
♦
♦

Sensor Failure

Actuated at 38,0°C for temperature settings lower than 37
ºC. Actuated at 40,0°C for temperature settings higher
than 37 ºC.
Actuat i the Ai Temperatu on the dom is 3, ºC belo the settin

f
r re
e
0
w
g
ed
point.
Actuated if the Air Temperature on the dome is 1,5 ºC higher
than the setting point.
Actuated if the NB Skin Temperature is 1,0 ºC higher than the
setting point.
Actuated if the NB Skin Temperature is 1,0 ºC below the setting
point.
Actuated when the Patient Sensor plug is disconnected or
when the sensor wire has a poor contact or even if the sensor is
loosened off the Patient skin. It only actuates on Skin Mode.

Oxygen Alarms (optional)
♦

Low Oxygen %

♦

High Oxygen %

♦

Calibration Failure

O2

♦

Sensor Failure

Actuated when the internal concentration of O2 is higher than
3% below the setting point.
Actuated when the internal concentration of O2 is higher than
3% above the setting point.
Actuated when an operational failure occurs during the Oxygen
Sensor calibration process.
Actuated when the Oxygen Sensor/UR plug is disconnected or


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

when the sensor wire has poor contact or when one of the cells
has its date expired.

Humidity Alarms (optional)
♦

H2O Low Level

♦

High Humidity - %
UR

♦

Sensor Failure

♦

Alarm of Low
Concentration of
UR

Actuated if the water level is reduced below the pre-determined level.
Actuated if the internal relative Humidity % UR is higher than
10% above the setting point.
Actuated when the Oxygen/UR Sensor Plug is disconnected, or
when the sensor wire has poor contact.
Activated if internal relative humidity % UR it is lesser of what
10% below of the adjustment point (Version 1186 Panel LCD).


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

Oxymeter Alarms (optional)
♦
♦
♦
♦
♦

SPO2 Low %
SPO2 High%
Low BPM
High BPM
Disconnected Sensor

♦ Dislodged Sensor
♦ Movement
2.1.8

set 0 to 100%
set 0 to 100%
set 0 to 250
set 0 to 250
when the sensor is not plugged to the device.
when the sensor is plugged to the device but disconnected
from the
patient.
it indicates the patient is moving.

- Alarms – Silencing / Restoring
Press to Silence
♦
♦

♦ Silence for up to 15
minutes

♦
♦

♦
♦

Press to Restore

♦ Restore

Alarm
Type
Low Air Temperature/ Skin
High Air Temperature / Skin
Low Water Level
High Humidity
Oxygen High Concentration
Low Oxygen Concentration
Alarm
Type

♦
♦

Skin Sensor Dislodging
Water Shortage

Note: Cancel the alarm if the alarm mode does not exist any longer.
2.1.9

- Circumstantial Requirements
♦ Operation Temperature Range

19 ºC to 28 ºC – Ambient

♦ Storage Temperature Range

0 ºC to 55 ºC – Ambient

♦ Operation Humidity Range

15% a 95% - Non Condensing

♦ Storage Humidity Range
♦ Humidity Sensor Operation Range
♦ Oxygen Sensor Operation Range
♦ O2 Sensor Calibration Pressure

0% a 90% - Non Condensing
20 °C to 42 °C
20 °C to 41 °C
600 to 900 mm Hg

♦ O2 Inlet Maximum Pressure, Servo

3,5
kgf/cm2


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

2.1.10

- Symbols
BF Type Applied Part

Class I Equipment

O
Electric

OFF (Without Feeding
Tension)
Attention: Potential
risk for
people
Obligatory

IPX4 Equipment Protected Against
Liquid Dripping

Attention: Electric Shock
Risk
ON (With Feeding
Electric
Tension)
Alternate Current

Protection Grounding

Grounding
∫∫∫

Attention: Hot Surface

Equipment not adequate
with inflammable
anesthetic mixtures

Attention: Refer to
Manual

Attention: Potential
Damage to the
equipment and its parts

Inhibit Sound

2.1.11

Contrast

- Symbols – Packaging

Fragile

This side up

Protect against Sun
Light

Protect from Rain

Stacking Limit

Attention:
Refer to
accompanyin
g
documentatio
n


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

Temperature
Limit for
transport and
storage

Hooks or bores
prohibited


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

2.2

- Technical Specifications - Kit for Integrated Pulse Oxymetry
Indication:

♦ SpO2 Measures

1 to 100%

♦ Pulse Measures

20 to50
bpm

Alarms:
♦ SpO2 High
♦ SpO2 Low

Set 0 to 100%.

♦ High BPM
♦ Low BPM
♦ Disconnected
Sensor

Set 0 to 250.
Set 0 to 250.
when the sensor is not plugged to the device.

♦ Dislodged Sensor

when the sensor is plugged to the device but disconnected
from the patient.
indicates that the sensor is moving.

♦ Movement

Set 0 to 100%.

Alarm Sound Inhibition:
The sound is inhibited by pressing the “INHIBIT
SOUND“ key, the heart beat BIP may only be inhibited being on
Attention: All alarms, when actuated, turn on the red led on the control panel.

Attention: Whenever the oxymeter is used, check for the alarm limits to ensure that they
are appropriate for the patient that is being monitored.

Attention: Optional item.

the oxymeter screen; a graphic information of the inhibited sound
will be displayed on the oxymeter screen.


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

3 - Parts, Pieces and Accessories
Code
093.004.70
0
093.004.80
0
093.004.85
0
093.005.70

0
093.005.80
0
093.005.85
0
093.007.70
0
093.007.80
0
093.007.85
0

Tension
127V~ 50/60Hz
220V~ 50/60Hz
240V~ 50/60Hz
127V~ 50/60Hz
220V~ 50/60Hz
240V~ 50/60Hz

127V~ 50/60Hz
220V~ 50/60Hz
240V~ 50/60Hz
093.006.70 127V~ 50/60Hz
0
093.006.80 220V~ 0
50/60Hz
093.006.85
240V~ 0
50/60Hz

ITE
M

Descripti
on
Dome with 5 oval ports / 1 iris sleeve / 2 Access Doors
(Front and Rear) / 8 Pipe Conductor. Basic Control Panel
with no optionals
Dome with 05 oval ports / 1 iris sleeve / 2 Access Doors
(Front and Rear)
/ 8 Pie Conductor. Intermediary Control Panel with Led´s
and with servo active Humidity .

Dome with 05 oval ports / 1 iris sleeve / 2 Access Doors
(Front and Rear)
/ 8 Pie Conductor. Intermediary Control Panel with Led´s and
with servo
active Humidity and scale.
Dome with 05 oval ports / 1 iris sleeve / 2 Access Doors
(Front and Rear)
/ 8 Pie Conductor. LCD Graphic Control Panel (enables
installation of all accessories)

DESCRIPT
ION

CODE

9

USER’S MANUAL
A 3186 NEONATAL INCUBATOR

1

2A

2B

Control Unit A 3186 Panel LED (without optionals) –
127V~ - 50/60Hz Control Unit A 3186 Panel LED
(without optionals) – 220V~ - 50/60Hz Control Unit A
3186 Panel LED (without optionals) – 240V~ - 50/60Hz

093.051.700
093.051.800
093.051.850

Control Unit A 3186 Panel LED with (optionals) –
127V~ - 50/60Hz Control Unit A 3186 Panel LED
with (optionals) – 220V~ - 50/60Hz Control Unit A
3186 Panel LED with (optionals) – 240V~ - 50/60Hz

093.052.700
093.052.800
093.052.850

Control Unit A 3186 Panel LCD with (optionals) –

127V~ - 50/60Hz Control Unit A 3186 Panel LCD
with (optionals) – 220V~ - 50/60Hz Control Unit A
3186 Panel LCD with (optionals) – 240V~ - 50/60Hz

093.053.700
093.053.800
093.053.850

2PA Dome with 05 oval ports / 1 iris sleeve / 2 Access Doors
(Front and Rear) / 8 Pipe Conductor / Compartment (enables
installation of all accessories)

093.053.600

Dome Double Wall 2PA

093.100.321

Access Panel Double Wall

092.116.321

10


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

3
4

5
6
7
8
9
10
11
12
13
14
15

16
17
18
19
20
21
22
3.1

Fixed Support - SFV
Ergometric Support – SEV – 127V~ -50/60Hz
Ergometric Support – SEV – 220 / 240V~ -50/60Hz
ADVANCED Phototherapy A 3006BB – 127V~ -50/60Hz
ADVANCED Phototherapy A 3006BB – 220V~ -50/60Hz
Right Left Vertical Rod Kit G3 ( for bumper)
Left Vertical Rod Kit G3 (without bumper)
Right Vertical Rod Kit G3 (without bumper)
Rotating Shelf G3 for Breathers

Column Serum Support G3
4 Auxiliary Switches Kit
6 Auxiliary Switches Kit
6 Auxiliary Switches (Schuko Type) Kit
Breather Adapter “Goose Neck”
ADVANCED Phototherapy A 3006 BTI
Motor group cleaning and disinfection tank – EMA model
Recirculating humidifier (only applicable on A 3186-STD)
Adhesive Box for patient’s sensor (50 units)
Adhesive Box for patient’s sensor (100 units)
Surrounding Bumper Kit
Lateral Bumper Kit
Right Drawer – 2 drawers
Right Drawer – 1 big drawer
Right Cabinet
Left Drawer – 2 drawers
Left Drawer – 1 big drawer
Left cabinet
Reviver Kit with O2 Reservoir (not illustrated)
Oxygen Servocontrol Kit 127V~ (not illustrated)
Oxygen Servocontrol Kit 220 / 240V~ (not illustrated)
Humidity Servocontrol Kit 127V~ (not illustrated)
Humidity Servocontrol Kit 220V~ (not illustrated)
Humidity Servocontrol Kit 240V~ (not illustrated)
Integrated Pulse Oxymetry Kit (not illustrated)
Integrated Scales Kit (not illustrated )
Box with disposable sensor ( 50 units )

090.050.600
090.058.700

090.058.800
006.020.700
006.020.800
094.052.600
094.050.600
094.051.600
094.054.600
094.053.600
090.051.600
090.082.600
090.147.600
013.050.600
006.001.900
086.100.321
087.000.600
086.076.600
086.068.600
094.055.600
094.056.600
090.190.600
090.078.600
090.090.600
090.079.600
090.189.600
090.089.600
020.013.600
093.054.700
093.054.800
093.055.700
093.055.800

093.055.850
093.054.900
093 056.900
092.162.600

- A 3186 Control Unit
In order to make the installation of optionals flexible, different Control Unit Models have been
devised. Therefore, the A 3186 Neonatal Incubator may be supplied with 3 types of Control
Unit:
-A
-A
-A

3186 Control Unit LED Panel LED without optionals;
3186 Control Unit LED Panel LED with optionals;
3186 Control Unit LCD Penal with

optionals. Exclusive use with the A 3186
Neonatal Incubator
11


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

3.1.1

- A 3186 Control Unit Panel with LED’s – Air and Skin Mode Control - No Optionals

ALARM

SKIN TEMPERATURE

POWER FAILURE

AIR TEMPERATURE

°C

SENSOR MISSING
AIR CIRCULATION
HIGH TEMPERATURE

°C

□

WARMING

SKIN 37°C – 38°C
AIR 37°C – 39°C

MODE SELECTION

ADJST TEMPERATURE
SKIN 34°C – 38°C
AIR 30°C – 39°C

LOW TEMPERATURE

GENERAL

□

□

°C

MICROPROCESSING CONTROL UNIT
This Control Unit will always accompany the basic A3186 Neonatal Incubator. Its front panel
is made up of numeric displays and led’s, which inform in a single manner and aims at the
programmed and controlled parameters.
As it is a basic Model, the installation of the Humidity ServoControl, Oxygen ServoControl,
Integrated Scales and Pulse Oxymeter optionals IS not possible.

A 3186 Control Unit
Panel
A 3186 Control Unit
Panel
A 3186 Control Unit
Panel

Descripti
on
(LED w/no optionals) – 127V~ 50/60Hz
(LED w/no optionals) – 220V~ 50/60Hz
(LED w/no optionals) – 240V~ 50/60Hz

Code
093.004.

700
093.004.
800
093.004.
850

Attention: The Humidity Servocontrol, Oxygen Servo Control, Integrated Scales and
Pulse Oxymeter Optional Items MUST not be installed in this Control Unit.

- A 3186 Control Unit Panel with LED’s – Air and Skin Mode Control with Servo
Active Humidity – with the Optional of Integrated Scales

3.1.2

ALARM

SKIN TEMPERATURE

POWER FAILURE

°C

SENSOR MISSING
AIR CIRCULATION
HIGH TEMPERATURE
LOW TEMPERATURE

AIR TEMPERATURE

SET

TEMPERATURE
SKIN 34°C –
38°C AIR 30°C –
39°C

WARMING

°C
MODE SELECTION

□

□

GENERAL

SKIN 37°C – 38°C
AIR 37°C – 39°C

□

°C

MICROPROCESSING CONTROL UNIT

12


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

This Control Unit may accompany the A 3186 Neonatal Incubators with some variations of
optionals. Its front panel is made up of numeric displays and leds, which inform in a simple
manner and aims the programmed and controlled parameters.
This model enables the installation of the Optional Integrated Scales. The optionals Pulse
Oxymeter and Oxygen Servo Control MUST NOT be installed in this model.

13


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

A 3186 Control Unit
Panel
A 3186 Control Unit
Panel
A 3186 Control Unit
Panel

Descripti
on
(LED w/ optionals) – 127V~ 50/60Hz
(LED w/ optionals) – 220V~ 50/60Hz
(LED w/ optionals) – 240V~ 50/60Hz

Code
093.005.
700
093.005.

800
093.005.
850

Attention: The Pulse Oxymeter and Oxygen ServoControl
Optional Items be installed in this Control Unit.

MUST
NOT

- A 3186 Control Unit Panel with Graphic LCD Display Air, Skin Mode Control
and Servo-Active Humidity with all optionals available

3.1.3

This Control Unit may accompany the A 3186 Neonatal Incubators with all kinds of available
optionals. Its front panel contains a graphic LCD Display, which fully informs the
programmed and controlled parameters such as the temperature graphs, Humidity, oxygen,
weight (optional), saturation, beats and plestimographic curves (Integrated Oxymeter –
optional). It also has the advantages of preventive maintenance control, integrated clock,
language selection, etc.
Descripti
on
A 3186 Control Unit
(LCD w/ optionals) – 127V~ Panel
50/60Hz
A 386 Control Unit Panel
(LCD w/ optionals) – 220V~ 50/60Hz
A 3186 Control Unit
(LCD w/ optionals) – 240V~ Panel

50/60Hz

Code
093.006.
700
093.006.
800
093.006.
850

Attention: All optional items may be installed in this Control Unit.

14


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

3.2

- Supports
The A 3186 Neonatal Incubator may be supplied with two support options, the Fixed Support
– SFV and the Ergometric Support – SEV.
Attention: The Ergometric Support – SEV is an optional item.

15


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

3.2.1

- Fixed Support – SFV – Re.: 090.050.600

Fixed height support SFV model (Re. 090.050.600), made up of 4 rotating wheels with brake.

This support may optionally be supplied with a set of drawers or cabinets, as per item 3.4
Drawers and Cabinets.
Exclusive use with the A 3186 Neonatal Incubator
3.2.2

-

Ergometric Support – SEV

Optional Support, of variable height, SEV model, electrically actuated, with a total course of

200mm, having 4 rotating wheels with brake. See reference chart below:
Suppo
rt
Type

Voltag
e (Volts)
V~

Frequen
cy Hertz
(Hz)

Re: FANEM
Code

SE
V

127

50/60

090.058.700

SE
V

220 /
240

50/60

090.058.800

Exclusive use with the A 3186 Neonatal
Incubator 3.3 - 5” (127mm) wheels with
brake – RE.:090.191.600
It raises the incubator at 12,5mm, in addition to providing lesser effort to move the
Attention: Optional Item.

equipment.

16


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

Exclusive use wit the A 3186 Neonatal Incubator
3.4 -

Drawers and Cabinets
The may be installed on the two types of supports, the fixed one and the ergometric one. Both
on the right and left sides.
There are two types of drawers, one with two drawers and the other with a big drawer. There
are also the cabinets. From these ones only one model may be chosen for each side, that is, one
right one and one left. Their references are:

17


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

Drawers
Drawer/Cabinet

Re. FANEM

Right 2 Drawers

090.190.600

Right 1 Big Drawer

090.078.600

Right Drawer

090.090.600

Left 2 Drawers

090.079.600

Left 1 Big Drawer

090.189.600

Left Cabinet

090.089.600

Attention: Optional Items

Exclusive use with the A 3186 Neonatal Incubator
3.5 -

Bumpers
In order to protect the A 3186 Neonatal Incubator, mainly during its transportation, two
types of bumpers may be installed. One Surrounding Model, which protects the entire
Incubator perimeter, and another lateral one, which protects the sides of the Incubator.

Surrounding Re.:093.070.600

Lateral Re.:093.069.600

Attention: Optional Item.

Attention: When installing the Bumper Kit in the A 3186 Neonatal Incubator, if the
installation of a Vertical Rod is required, use Right or Left Rod (without arm)
RE.:094.052.600.

18


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

Exclusive Use with the A 3186 Neonatal Incubator

19


USER’S MANUAL
A 3186 NEONATAL INCUBATOR

3.6 -

Vertical Rods
The A 3186 Neonatal Incubator may have Vertical Rods, one Right and One Left one,
which may support the Rotating Shelf and the Serum Support Kit. The installation of the

rods is independent of the support configuration, and may be installed on the fixed and
ergometric supports, such as any configuration of drawers and cabinets.

094.050.600
(LEFT
with arm)

094.051.600
RIGHT(with
arm)

094.052.600
(RIGHT OR
LEFT
(without
arm)

Attention: Optional Item.

Attention: The Right or Left Rod (no arm) RE.:094.052.600 may only be requested if a
Bumper Kit is installed. If there is not a bumper installed, request Rod Kits
(with arm).

Exclusive use with the A 3186 Neonatal Incubator
3.7 -

Rotating Shelf
Rotating Shelf that can be fixed on the top of the Vertical Rods, one per rod. Ideal for
monitor coupling, breathers and infusion pumps, each shelf supports the maximum load of
10kg.

20