ĐỀ THI CHỨNG CHỈ SOLIDWORKS CSWP( tieng anh)

ĐỀ THI CHỨNG CHỈ SOLIDWORKS CSWP
Phần 1:
Question 1 of 37: For 5 points.
S1A300- Part Creation and Modification Problem set.
This text decribes the problem that must be solved in this problem set. Please
read this in it’s entirety before proceeding and click yes for 5 points.
Please note that the use of other test taker’s complete models and assemblies
can lead to the annulment of your results per the candidate conduct policy you
agreed to
- You will create part using the drawings and parameters specified in the
following questions.
Not # 1: The images shown may not be to proportion depending on the
parameters you are given. They are meant as a reference only for the
dimensions and parameters used to create the part.
- The part’s geometry will then be modified by adding or removing
features specified. These major modifications are stages of the part.
Not #2: Any dimensions that are related to new features being added to the
part for the current question will be cicled in the images
- Between each stage the part will be updated using variable dimensions
specified by letters.
Other important notes:
Not #3: All dimensions needed to build the part correctly and follow the design
intent are represented in the images.
Not#4: Your answers should be within 0.5% of the correct answer to be
marked correct. For example, if the correct answer is 500 grams, then the
allowed error deviation for your answer is 2,5 grams
Hint : To save the most time, make use of linked dimensional values and
equations
Please click yes for 5 points and continue to the next question.

1

 Yes.
Question 2 of 37: For 10 points.
S1A301002- stage 1:
Build this part in Solidworks.( save part after each question in the diferent file
in case it must be reviewed )
Unit system: MMGS (millimeter, grams, second)
Decimal places : 2
Part origin: Arbitrary.
Material: 1060 Alloy Aluminum.
Densyti: 2700kg/m3.
All holes through all unless shown otherwise .
Radius of fillets and rounds =10mm unless otherwise noted.
Note: New fillets and rounds to be created are highlighted in RED in the
images for better clarity.
2


- There are 14 total filleted edges , R=10 mm.
- Use the following parameters and equations which correspond to the
dimensions labeled in the images
A= 222mm
B= 81mm
X=A/4
Y= (2*B)/3
- Measure the mass of the part.
What is the mass of the part (grams).

3

1305.28
1225.28

1365.28
 1265.28

Question 3 of 37: For 10 points.
S1A302007 – Update parameters of stage 1.
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed ).
Unit system: MMGS ( millimeter , grams , second).
Decimal places: 2
Part origin: Arbitrary.
Material: 1060 Alloy Aluminum.
Density = 2700kg/m3.
All holes through all unless shown otherwise.
Radius of fillets and rounds =10mm unless otherwise noted.
- Use the part from the previous question.
- The geometry of the part has remainted constant from the previous
question except for the values of the parameters listed below.
- Update the parameters to the following values.
A =252mm.
B= 89mm.
X= A/4.
Y = (2*B)/3.
- Measure the mass of the part.
What is the mass of the part ( grams)?

4


Enter value:
5


(use, (points) as decimal separator)

Questions 4 of 37: For 10 points.
S1A303003- update parameter of stage 1.
Build this part in Solidworks. (save part after each question in a differenf file
in case in must be reviewed) . Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
Use the part from the previous question.
The geometry of the part has remained constant from the previous question
except for the values of the parameter listed below.
Update the parameters to the following values :
A= 204 mm
B=72 mm
X= A/4
Y= (2*B)/3
Measure the mass of the part.
What is the mass of the part (gram)?
Enter Valus

Picture 1

6


Picture 2

Picture 3

7


Question 5 of 37: for 10 points.
S1A304001 – Stage 2: Build this part in Solidworks. ( Save part after each
question in a different file in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Picture 4
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.
The part is to be modified using the following instructions and parameters. The
changes are concentrated in areas AA and BB indicated in the image.
Noted: New fillets and rounds to be created are highlighted in RED in the
images for better clarity.
There are 18 total filleted edges, R=10mm.
Noted #2: Any dimensions that are related to new features being added to the

part for the current question are circled in the images for clarity.
Use the following paremeters and equations which correspond to the
dimensions labeled in the images :
A= 220mm
B=80mm
X= A/4
8


Y= (2*B)/3
Z=(A/8)-5mm
Measure the mass of the part.
What is the mass of the part (gram)?
 1334.81
1394.81

 1274.81
1374.81

Picture 1

9

Picture 2


Picture 3

Picture 4

10


Picture 5
Question 6 of 37: For 10 points.
S1A305001: - Update parameters of stage 2.
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.
The geometry of the part has remained constant from the previous question
except for the values of the parameters listed below.
Update the parameters to the following values:
A= 200mm
B= 95mm
X= A/4
Y=(2*B)/3
Z= (A/8)-5mm
Measure the mass of the part.
What is the mass of the part (gram)?
Enter values:

11

Picture 1

Picture 2

12


Picture 3

Picture 4
Question 7 of the 37: For 10 points.
S1A306003- Update parameters of Stage 2.
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
13


Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.
The geometry of the part has remained constant from the previous question
except for the values of the parameters listed below.
Update the parameters to the following values:
A= 236mm

B= 72mm
X= A/4
Y=(2*B)/3
Z= (A/8)-5mm
Measure the mass of the part.
What is the mass of the part (gram)?
Enter values:

Picture 1

Picture 2
14


Picture 3

Picture 4
Question 8 of 37: For 10 points.
S1A307009- Stage 3:
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
15

Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.
The part is to be modified using the following instructions and parameters. The
changes are concentrated in areas AA and BB indicated in the image.
Noted: New fillets and rounds to be created are highlighted in RED in the
images for better clarity.
There are 16 total filleted edges, R=10mm.
Noted #2: Any dimensions that are related to new features being added to the
part for the current question are circled in the images for clarity.
Use the following paremeters and equations which correspond to the
dimensions labeled in the images :
A= 228mm
B=88mm
X= A/4
Y= (2*B)/3
Measure the mass of the part.
What is the mass of the part (gram)?
1490.37
1550.37
1450.37
1410.37

Picture 1

16


Picture 2

Picture 3

Picture 4

Picture 5
17


Question 9 of the 37: For 10 points.
S1A308005- Update parameters of Stage 3.
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.
The geometry of the part has remained constant from the previous question
except for the values of the parameters listed below.
Update the parameters to the following values:
A= 233mm
B= 93mm
X= A/4
Y=(2*B)/3
Measure the mass of the part.
What is the mass of the part (gram)?
Enter values:

18


Picture 1

Picture 2

Picture 3

19


Picture 4
Question 10 of the 37: For 10 points.
S1A309003- Update parameters of Stage 3.
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.
The geometry of the part has remained constant from the previous question
except for the values of the parameters listed below.
Update the parameters to the following values:
A= 240mm
B= 100mm

X= A/4
Y=(2*B)/3
Measure the mass of the part.
What is the mass of the part (gram)?
Enter values:

20


Picture 1

Picture 2

Picture 3
21


Picture 4
Question 11 of the 37: For 10 points.
S1A310002- Update parameters of Stage 3.
Build this part in Solidworks. ( Save part after each question in a different file
in case it must be reviewed).
Unit system MMGS (millimeter, gram, second).
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy Aluminum.
Density: 2700kg/m3.
All holes through all unless shown otherwise noted.
Radius of fillets and rounds = 10mm unless otherwise noted.
Use the part from the privous question.

The geometry of the part has remained constant from the previous question
except for the values of the parameters listed below.
Update the parameters to the following values:
A= 247mm
B= 107mm
X= A/4
Y=(2*B)/3
Measure the mass of the part.
What is the mass of the part (gram)?
Enter values:

22


Picture 1

Picture 2

23


Picture 3

Picture 4
Question 12 of the 37: For 5 points.
S2A401001- Modify Existing part problem set.
This text describes the problem that must be solved in the segment. Please read
this in its entirety before proceeding and click yes for 5points.
Please note that the use of other test taker’s completed models and assemblies
can lead to the annulment of your results per the candidate Conduct policy you

agreed to.
Note: the images shown may not be to proportion depending on the parameters
you are given. They are meant as a reference only for the dimensions and
You will be asked to do the following:
- Modify specific areas of the part.
- Modify part geometry.
24


- Modify key dimensions.
You may modify the part in any way necessary in order to correctly achieve the
changes that are instructed while preserving the areas of the part where no
changes are asked for.
For the final 4 questions you will open an existing part and modify its geometry
based on the use of and modify its geometry based on the use of configuration s
You will be asked to do the following:
- Analyze existing configurations correctly.
- Modify geometry.
- Modify existing configurations.
- Create new configurations.
Download and save the attached zip file. This zip file contains all the parts you
will need for this problem set.
Open the download zip file and save the contents to a location the Solidworks
can access on your computer.
Save the part at each question with a unique name in case it needs to be
reviewed .
Please click yes for 5 points and continue to the next questions.

Question 13 of the 37: For 9 points.
S2A402001- Change angle .

25