Tài liệu LoopStar® 714 and LoopStar® 718 Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities docx

LoopStar
®
714 and LoopStar
®
718
Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities
We all hear about the glut of fiber in the ground today. Unfortunately not much of it really exists in the last
mile. T1s and E1s are still the primary mode of transport for a majority of locations. So how do you provide
economical business-class Ethernet services to your off-net customer locations that can only be reached
through T1s or E1s? How do you offer Ethernet bandwidth and cost savings to customers who thought they
could only get Frame Relay service, speeds and pricing?
The LoopStar 714 and LoopStar 718 are tailored to help service providers reach their off-net customers and
reduce service fees at the same time. The LoopStar 714 offers highly manageable 10/100 customer access and
up to four T1/E1s (eight T1/E1s for the LoopStar 718) for the network connection. These T1/E1s are bonded
using the standard Multilink Point-to-Point Protocol (MLPPP), offering up to 12 Mb/s (T1) or 16 Mb/s (E1) of
service. Additional lines can be added as necessary, and with a simple-to-use Graphical User Interface (GUI),
provisioning new circuits has never been easier. And the LoopStar products come equipped with LoopStar 700
intelligent management, designed to support remote service provisioning, verification, and troubleshooting.
From RMON counters and Ethernet / WAN loopbacks to a built-in Ethernet port Time Domain Reflectometry
(TDR) test, from complete Layer 2+ classification and service definition to link quality monitoring and
reporting, the LoopStar 714 and LoopStar 718 provide the flexibility and scalability to deliver customer-
specific solutions and support with pinpoint accuracy.
Flexible and Differentiated Ethernet Solutions
Offering business-class Ethernet services by providing strong Class of Service (CoS) features, the
LoopStar 714 and LoopStar 718 can be used for:
• Point-to-point and hub-and-spoke deployments
• Full range of 4,096 Virtual LANs
• Layer 2 Virtual Private Networks (VPNs)
• Traffic prioritization and classification
For example, with the advanced traffic classification features of the LoopStar 714 and LoopStar 718, Voice over
IP (VoIP) traffic can be given priority over Internet access traffic. The LoopStar products support up to 10 rule-

based classifications based on any of the following inputs: VLAN ID, VLAN P-bits, ToS bits and DiffServ Code
Points. In addition to this classification scheme, rate limiting and policing are also provided to round out a full
suite of tools for customer provisioning and service.
SPEC SHEET SPEC SHEET
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Features
• Multilink Point-to-Point Protocol (MLPPP)
• ‘Plug-and-play’ platform and design
• LoopStar 700 Intelligent Management Capabilities
• LoopStar 700 Traffic Management
• LoopStar 700 Performance and Fault Management
01/06 • 102157AE
LoopStar
®
714 and LoopStar
®
718
LoopStar
®
714 and LoopStar
®
718
Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities
2
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Benefits
• Cost-effective approach to deliver Ethernet services over NxT1 and NxE1
• ‘Plug-and-Play’ design for easy installation, configuration and management
• Proven management software with comprehensive and robust features
• Standard MLPPP bonding means T1/E1s can be added as customer bandwidth needs grow

• Simple replacement for Frame Relay services
• Bond from 1-8 T1/Es to provide bandwidth ranging from 1.5 Mb/s to 16 Mb/s; automatic removal / restoration
of failed links
• Compact design makes it simple to install at the customer premise, either as a wall-mounted or
rack-mounted unit
• Allow for easy access to configure or disable access and ports from anywhere; secure in-band management
access from anywhere on the network
• Customer traffic classification, supporting up to 10 traffic rules per device, as well as VLAN management, traffic
queuing, rate limiting and policing
• Support for both Layer 1 and Layer 2 performance monitoring statistics, as well as facility alarms available over
both the in-band management channel and the local management console port
• Built-in loopbacks and a built-in Ethernet port Time Domain Reflectometer keep service calls to a minimum
Easy Fit into Existing OAM&P Infrastructure
In conjunction with the LoopStar 700 suite’s in-band management VLAN channel, robust GUI and full SNMP
connectivity, the LoopStar 714 and LoopStar 718 are easy to configure, manage and monitor. Performance
monitoring is supported for both the T1/E1 and Ethernet interfaces. Fault management is covered through the use
of equipment and facility alarms available over both the in-band management channel and through the local
management console port. The LoopStar 714 and LoopStar 718 provide a strong set of carrier operational support
tools, which extend beyond standard T1/E1 loopback testing and reach all the way to the user-facing Ethernet port.
The LoopStar 714 and LoopStar 718 complement the LoopStar 700 product line, enabling service providers to create
new business service revenues by delivering high-margin Ethernet services to all of their customers, no matter where
they are located on the network.
Bonded T1/E1s
T1/E1
Ethernet
Switch/Router
Ethernet
VoIP PBX
Core
LS

750
LS
714
LS
718
The LoopStar 714 and LoopStar 718 offer business-class Ethernet to any size location.
01/06 • 102157AE
LoopStar
®
714 and LoopStar
®
718
LoopStar
®
714 and LoopStar
®
718
Extend Ethernet Services to All Customers Over Readily Available T1/E1 Facilities
3
www.adc.com • +1-952-938-8080 • 1-800-366-3891
Specifications
Interfaces: 1 x 10/100Base-T port
1 x 100Base-FX (SM or MM SFP)
8 x T1/E1 interfaces, supports 1 MLPPP bundle (LoopStar 718)
4 x T1/E1 interfaces, supports 1 MLPPP bundle (LoopStar 714)
1 x 10/100 management port
Maintenance: T1/E1 loopbacks and PM
Ethernet loopbacks and PM
Ethernet cable testing with TDR
WAN Protocol: RFC1661: Point-to-Point Protocol (PPP) and Link Control Protocol (LCP)

RFC1990: PPP Multilink Protocol (ML-PPP)
RFC3518: Bridging Control Protocol (BCP)
Automatic removal/restoration of failed links
Ethernet Services: 802.1p prioritization
802.1Q VLAN tagging/switching/stacking
Rate limiting: 128-500 kb/s increments
CoS: WRR or strict priority based on VLAN, p-bits or ToS/DSCP
Management: IP host with DHCP client for automatic address assignment
In-band management VLAN
Web-based management interface (GUI)
SNMP agent supporting standard MIBs, including RMON
FTP client for download
LoopStar 700 intelligent management
Power Options: AC Power: 100-240 V auto ranging, 47-63Hz
DC Power: Dual DC Feeds -48 VDC nominal (-40 to -60 VDC) or 24 VDC
Physical: 1 RU (1.75" x 17" x 7.25")
Wall-mount or rack-mount (19" and 23")
Full front access (ETSI form factor)
Temperature hardened (option)
-40° to +65° C (operating)
-40° to +70° C (storage)
Regulatory: UL Listed
EN/UL 60950
CE Mark
FCC Part 15 Class B
NEBS Level 3 certified
ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101
Specifications published here are current as of the date of publication of this document. Because we are continuously
improving our products, ADC reserves the right to change specifications without prior notice. At any time, you
may verify product specifications by contacting our headquarters office in Minneapolis. ADC Telecommunications,

Inc. views its patent portfolio as an important corporate asset and vigorously enforces its patents. Products or
features contained herein may be covered by one or more U.S. or foreign patents. An Equal Opportunity Employer
102154AE 1/06 Original © 2006 ADC Telecommunications, Inc. All Rights Reserved
Web Site: www.adc.com
From North America, Call Toll Free: 1-800-366-3891 • Outside of North America: +1-952-938-8080
Fax: +1-952-917-3237 • For a listing of ADC’s global sales office locations, please refer to our web site.
SPEC SHEET
Ordering Information
Description Catalog Number
LPS-714 AC Package (1 10/100, 1FX, no optics, 4-T1/E1)
*Includes: 1 AC power supply and AC power cord, 19” and 23” LPS-714-AC L1
rack mount brackets, license for basic software and documentation
LPS-714 DC Package, Temperature Hardened (1 10/100BT, 1FX, no optics,
4-T1/E1) *Includes: Internal dual feed - 48Vdc power supply, 19” and 23” LPS-714-48DC L1
rack mount brackets, license for basic software and documentation
LPS-714 24DC Package, Temperature Hardened (1 10/100BT, 1FX, no optics,
4-T1/E1) *Includes: Internal dual feed - 24Vdc power supply, 19” and 23” LPS-714-24DC L1
rack mount brackets, license for basic software and documentation
LPS-718 AC Package, (1 10/100BT, 1FX, no optics, 8-T1/E1)
*Includes: 1 AC power supply and AC power cord, 19” and 23” LPS-718-AC L1
rack mount brackets, license for basic software and documentation
LPS-718 48VDC Temperature Hardened, (1 10/100BT, 1FX, no optics, 8-T1/E1)
*Includes: Internal dual feed -48dc power supply, 19” and 23” LPS-718-48DC L1
rack mount brackets, license for basic software and documentation
LPS-718 24DC Temperature Hardened, (1 10/100BT, 1FX, no optics, 8-T1/E1)
*Includes: Internal dual feed -24Vdc power supply, 19” and 23” LPS-718-24DC L1
rack mount brackets, license for basic software and documentation