Mô hình Statue of Liberty, America, Tượng nữ thần tự do, Mỹ. P4

Statue of Liberty, U.S.A.: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C

Before starting assembly:Writing the number of each section on its
back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting
out the sections.)

/>Miniature stand

Indicates where sections should be glued together.
Indicates where to insert sections.
Do not glue the sections together.
Indicates sections that should be glued first,
then cut out.

Star-shaped stand
Build parts 2 and 4 in the same way.

Choose the stand
you like best.

Photo
competed model
View of completed
model

Align and glue the rear surfaces together.

*This model was designed for Papercraft and may differ from the original in some respects.

Assembly Instructions:Six A4 sheets(No.1 to No.6)
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.

*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.

Attach the
reinforcement
with glue first.

Align and glue the rear surfaces together.

Fold these parts inward and align
and glue their surfaces together.

Assembly Instructions
Mountain fold(dotted line)

Make a mountain fold.
Valley fold(dashed and dotted line)

Make a valley fold.
Scissors line(solid line)

Cut along the line.
Cut in line(solid line)

Cut along the line.

Tools and materials
Assembly tip
Caution

Glue
The glue spot(colored dot)
shows where to apply the glue.

Glue spot(Red dot)

Glue parts with the same number together.
Glue spot(Green dot)

Glue within the same part.
Glue spot(Blue dot)

Glue to the rear of the other part.

Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.

Align and glue the rear
surfaces together.

Build four identical versions of part 10.

Statue of Liberty, U.S.A.: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C

*Glue the parts together in
the sequence shown in steps 1 - 6.

Align and glue the
rear surfaces together.

Position the short side
on this side

Position the elevator
entrance on this side.


Statue of Liberty, U.S.A.: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C

Curve the interior side
of this part.

Insert and glue to
the rear surface.

View from rear

Position so that the narrower
side is located on this side.

* Cover the statue with the upper robe.
No gluing is necessary.
After positioning the rear surfaces
of the side parts together,
glue the rear sides of the corners together.


Statue of Liberty, U.S.A.: Assembly Instructions

Cut after gluing
the rear surfaces
together.

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C

Glue the rear
surfaces together.

Glue the rear panels of parts 41 and 43,
between which the four sheets of part 42
are sandwiched.

Glue the statue's
fingertips here.

Glue to part 29 on the interior side.

Insert and glue the glue tabs
to the interior side of this spot.

Fold the fingertips inward
and glue to the Declaration of Independence.

Lightly bend this part as
shown in the illustration.

Insert to assembled
part 47 along this line.


Statue of Liberty, U.S.A.: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C

Miniature stand

*Position in place. No gluing needed.

Finished!


Statue of Liberty, U.S.A.: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Hiroshi Chiba / PAPERART-C

Star-shaped stand

*Position in place without gluing.

*Place this part on the stand without gluing.
Finished!