Tài liệu sửa chữa xe ô tô Renault 19 (Repair Manual) - P11

77 11 190 895
NOVEMBER 1996
Edition Anglaise
Trim and Upholstery
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes by the manufacturer in the
production of the various component units and accessories from which his vehicles
are constructed".
All copyrights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault.
C
Renault S.A. 1996
GENERAL
SIDE OPENING ELEMENTS TRIM
FRONT SEAT FRAMES AND SEAT RUNNERS
REAR SEAT FRAMES ANDSEAT RUNNERS
FRONT SEAT TRIM
REAR SEAT TRIM
SEAT FITTINGS
TRIM FOR OPENING ELEMENTS (
OTHER THAN SIDE
)
BODY INTERIOR TRIM
REAR SHELVES
EXPLODED VIEW
PRC70.3
A Front and rear door handles
B Interior trim fastenings on body side

C Centre pillar upper trim
D Front, centre and rear pillar lower
trim
E Front pillar upper trim
F Rear quarter panel trim
F Rear section lower trim (saloon)
F Rear quarter panel trim (cabriolet)
G Sill Panel - Seat belts
A Tooling and products
Pages
Contents
Trim
71-1
71-2
71-3
71-4
71-5
71-5
71-6
71-7
71-8
BODY INTERNAL TRIM
71
SIDE OPENING ELEMENTS
TRIM
A Door storage compartment
B Front door trim
B Front door trim (phase II)
B Front door trim (cabriolet)
C Rear door trim

72
72-1
72-2
72-3
72-5
72-6
Pages
70-1
GENERAL
70
A Bonnet trim
B Tailgate trim
C Hood exterior trim (cabriolet)
D Padding (cabriolet)
E Hood interior trim (cabriolet)
F Changing the hood bonded rear
screen (cabriolet)
G Changing the hood rear screen
secured by zip fastener (cabriolet)
73-1
73-1
73-2
73-7
73-9
73-13
73-20
TRIM FOR OPENING ELEMENTS
(OTHER THAN SIDE)
73
A Side shelf

B Side shelf (utility version)
C Shelf trim (saloon)
74-1
74-2
74-3
REAR SHELVES
74
A Complete seat
B Seat frame
C Seat runners
D Seatback frame
75-1
75-3
75-4
75-5
FRONT SEAT FRAMES AND
SEAT RUNNERS
75
Contents (cont.)
Pages
A Complete seatback
B Seatback frame
76-1
76-1
REAR SEAT FRAMES AND
SEAT RUNNERS
76
A Seat trim
B Seatback trim
77-1

77-3
FRONT SEAT TRIM
77
A Rear bench seat frame
B Seat trim
B Seat trim (cabriolet)
C Seatback trim
C Seatback trim (cabriolet)
78-1
78-2
78-3
78-4
78-5
REAR SEAT TRIM
78
A Head restraint trim
B Ski flaps (cabriolet)
B Rear head restraints (cabriolet)
79-1
79-2
79-2
SEAT FITTINGS
79
1 - Stapler tool Type :
NAUDER*
and stainless steel clips
2 - Rivets Part number :
77 03 072 280
3 - Neoprene adhesive
4 - Brush

5 - Seal Part number:
* NAUDER
:
Please contact your local After Sales Head Office
for details.
94791S
GENERAL
Tooling and products
70
A
D 53
CABRIOLET
70-1
REMOVAL
Insert a flat screwdriver in hole (2) in the upper
section, so that the first part of the handle can be
levered away and unhooked.
92260R
BODY INTERIOR TRIM
Front and rear door handles
71
A
The handle is held by two screws (3).
92261R
71-1
NOTE
: If the dashboard is in place there is a risk of fastenings (A) ), (B), (C) and (D) breaking on removal. For
reasons of quality, it is preferable to change them, even if they can be re-used.
PRF7101
BODY INTERIOR TRIM

Interior trim fastenings on body side
71
B
(A) Snap fastening
90230R1
(C) Snap fastening
90231R
71-2
REMOVING THE UPPER TRIM (1)
Unpick the upper section then free the seals by
pulling it away.
Remove:
- the seat belt mounting from the centre pillar,
- the seat belt height adjustment pushrod
(component in two sections).
92340R
BODY INTERNALIOR TRIM
Centre pillar upper trim
71
C
92339G
Remove the sliding cover from the adjustable
mounting.
71-3
Remove:
- the upper trim from the centre pillar (1) see section 71 B
- the mounting screws,
- the lower seat belt mounting.
By hand, free the rear part of the trim from the surrounding seal and remove clips (B).
Proceed in the same way for the front part of the trim.

Take out the trim through the rear door aperture.
PRF7102
BODY INTERIOR TRIM
Front, centre and rear pillar lower trim
71
D
71-4
Remove:
- the upper trim (1) from the centre pillar,
- the mounting screw,
- unpick the trim by pulling section (F) straight
downwards then backwards.
PRF7103
BODY INTERIOR TRIM
Front pillar upper trim
71
E
Rear quarter panel trim
71
F
Remove (see exploded view in section 71 B) :
- trims (1), (2), (6) and (7) ,
- the seal from the luggage compartment aper-
ture frame,
- the side shelf which is held by 5 screws,
- the two upper screws from the quarter panel
trim.
Unpick the trim (2 clips (C)) then remove the trim,
starting at the door seal end.
PRF7104

71-5
Remove in the following order:
1 - 2 - 3
PRF7105
BODY INTERIOR TRIM
Rear section interior trim
71
F
L 53
SALOON
71-6
REMOVAL
PRF7106
BODY INTERNAL TRIM
Rear quarter panel trim
71
F
D 53
CABRIOLET
Open the hood and tilt the rear seat.
Remove the lower seat belt mounting and the
hood opening handle.
94810R
Remove nut (A) and unclip the fir tree type clips.
Detach the trim from the rubbing strip.
94811R
71-7
SILL PANEL
Fit the two lower sill panel trims (1) which serve as a storage compartment in the bottom of the side panel
trim.

REAR SEAT BELTS
Unclip:
- the trim between the left and right hand rear quarter panels,
- the rear quarter panel trims starting at the quarter light side and remove the seat belt blanking piece.
Fit the rear seat belt retractor in the rear quarter panel.
Route the belt and the guide through the opening in the rear quarter panel trim, then clip the guide to the
trim.
Reclip the panel trim and the centre trim.
Secure:
- The end of the seat belt to the sill panel trim at (4),
- the two seat belt stalks (5) to the floor panel after first removing the mastic from the mountings.
BODY INTERIOR TRIM
Sill panel - Seat belts
71
G
PRJ4020
S 53
UTILITY VERSION
71-8
Remove:
- the speaker grille by unscrewing it 1/4 of a
turn,
- the speaker which is held by 4 screws,
- the 4 screws holding the speaker mounting,
- the mounting (6) and free the storage
compartment from the lower snap fastenings
(7), by pushing it upwards.
Disconnect the electric switch feed (8).
There is a leaktight rivet (9) holding the lower
snap fastening in place (component stays on the

door).
HIGH SPECIFICATION MODEL TYPE STORAGE
COMPARTMENT
92262R
SIDE OPENING ELEMENTS TRIM
Door storage compartment
72
A
Remove the two screws (5) and free the storage
compartment from the lower snap fastenings (7),
by pushing it upwards.
BASIC MODEL TYPE STORAGE COMPARTMENT
92263R
72-1
(1) pressure stud
(2) clip on door
Remove the trim.
NOTE :
the trim is clipped in place (1) and sealed
by mastic.
To remove it, the trim must be unpicked and uns-
tuck gradually (use a saw blade to cut the mastic)
then free it from the upper rubbing strip.
NOTE
: when changing a door or the trim, trim
sealing mastic part number 77 01 421 049 must be
reapplied (see Technical Note N.T. 219 "DOOR
TRIM SEALING MASTIC").
Remove:
- the internal opening control,

- the internal door handle,
- the rear view mirror base cover,
- the door storage compartment,
- the window winder.
92264R
SIDE OPENING ELEMENTS TRIM
Front door trim
72
B
72-2
REMOVAL
95859-1S
SIDE OPENING ELEMENTS TRIM
Front door trim
72
B
X 53
PHASE II
PRF7201
Unclip the rear view mirror mountings cover.
95859S
Remove the pulling handle cover.
Disconnect the various switches.
72-3
SIDE OPENING ELEMENTS TRIM
Front door trim
72
B
X 53
PHASE II

Remove:
- the pulling handle,
- the loud speaker grille and storage compart-
ment,
- the internal handle.
For all removal-refitting operations, the door trim
seal must be changed.
PRF7202
72-4
Remove:
- the rear view mirror internal cover (1),
- the internal handle (2),
- the internal opening handle (3),
- the speaker grille(4),
- the storage compartment(5).
Disconnect the rear view mirror harness (left hand
side).
PRF7203
SIDE OPENING ELEMENTS TRIM
Door trim
72
B
D 53
CABRIOLET
94792R
72-5
(1) pressure stud
(2) clip on door
Remove the trim.
NOTE :

the trim is clipped in place (1) and sealed
by mastic.
To remove it, the trim must be unpicked and uns-
tuck gradually (use a saw blade to cut the mastic)
then free it from the upper rubbing strip.
NOTE
: when changing a door or the trim, trim
sealing mastic part number 77 01 421 049 must be
reapplied (see "BODYWORK REPAIRS" poster).
Remove:
- the internal opening control,
- the internal door handle,
- the ashtray,
- the window winder.
92265R
SIDE OPENING ELEMENTS TRIM
Rear door
72
C
72-6
PRF7302
Remove the two screws (1) and two hooks (2).
Unclip the trim.
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Bonnet trim
73
A
PRF7301
Tailgate trim
73

B
73-1
Opening the hood
PRF7303
Lift the rear of the hood.
Remove the safety device and open the hood
compartment.
Fold the rear section of the hood back into the
compartment.
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Hood exterior trim
73
C
D 53
CABRIOLET
The operations described below must be carried out on both the left hand and right hand sides.
Any incorrect operation of the hood triggers an alarm. The order of operations must be followed.
Fold the sun visors forwards.
Open the front locks without folding back the
hood.
Operate the unlocking handle (this opens the rear
hood locks and the hood compartment).
73-2
Remove the plastic clips.
Free the two sections of material which corre-
spond to the front section.
After opening the hood
Removal
Remove the rear seals and slides.
Remove the four plastic clips.

94787S
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Hood exterior trim
73
C
D 53
CABRIOLET
Remove the front angle piece and the two corner
segments.
94762
Remove the seals from the front sections by sli-
ding them.
Remove their slides (6 torx screws).
73-3
At the front, remove the tensioning cable rivet
and remove the cable from the trim.
Free the two corresponding pieces of material.
Undo the trim side mountings. (Quarter panels).
94971S
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Hood exterior trim
73
C
D 53
CABRIOLET
Lift the rear of the hood and remove the hood
frame rubber seal.
73-4
Free the rear screen tensioning material and re-
move the external hood trim.

94788S
Remove the formed section of the rear part of the
hood.
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Hood exterior trim
73
C
D 53
CABRIOLET
Remove the rivets at the rear ends and at the
front of the rear pillar.
73-5
Start at the rear.
Clip the rear section taking care to centre the
hood (it is marked).
Route the tensioning cable and secure it.
Refitting
94788S
TRIM FOR OPENING ELEMENTS (OTHER THAN SIDE)
Hood exterior trim
73
C
D 53
CABRIOLET
Fold the hood forwards.
Stick the rear screen stiffener.
Refit the rubber seal.
Tilt the hood towards the rear and stick the front
section.
Drill the holes in the trim and refit the plastic clips.

Re-secure the front angle piece and the side seg-
ments.
Close the hood completely and stick the side sec-
tions. Ensure that there are no creases.
Refit the small side tensioning straps.
73-6