Toyota land cruiser 1998 2007 brake hệ thống thắng xe trên land cruiser đời 1998 2007

BR12E-07
F06425
TOYOTA
Hand-held
Tester
DLC3
BR-4
-BRAKE BRAKE FLUID
2140Author: Date:
2004 LAND CRUISER (RM1071U)
BRAKE FLUID
BLEEDING
HINT:
z If any work is done on the brake system or if air in the
brake lines is suspected, bleed the air from the system.
z When bleeding, keep the amount of the fluid within the
line of reservoir between Min. and Max.
NOTICE:
z Do not let brake fluid remain on painted surfaces.
Wash it off immediately.
z With the reservoir cap removed, when depressing the
brake pedal, the fluid will spray.
1. FILL RESERVOIR WITH BRAKE FLUID
Fluid: SAE J1703 or FMVSS NO. 116 DOT3
2. In case of using TOYOTA hand-held tester:
BLEED HYDRAULIC BRAKE BOOSTER
HINT:
If the hydraulic brake booster has been disassembled, discon-
nect the brake line from the hydraulic brake booster or if the res-
ervoir becomes empty, bleed the hydraulic brake booster.
(a) Turn the ignition switch OFF, depress the brake pedal

more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(b) Turn the ignition switch ON, check that the pump stops af-
ter approx. 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (a) and (b) again.
(c) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(d) Observe the procedure in step 4 and bleed the right and
left front brake caliper.
(e) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.
(f) Connect TOYOTA hand-held tester.
(1) Turn the ignition switch OFF, connect the TOYOTA
hand-held tester to DLC3.
(2) Turn the ignition switch ON and select ”AIR BLEED-
ING” on the TOYOTA hand-held tester.
HINT:
Please refer to the TOYOTA hand-held tester operator’s manu-
al for further details.
F04459
F09169
F09632
w/ ABS Only:
w/ ABS & BA & TRAC & VSC Only:

-BRAKE BRAKE FLUID
BR-5
2141Author: Date:
2004 LAND CRUISER (RM1071U)
(g) Bleed right front brake line.
(1) Select ”FR LINE” on the TOYOTA hand-held tester.
(2) With ”FR LINE” turned ON with the TOYOTA hand-
held tester, depress the brake pedal and hold it to
bleed the right front brake caliper.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.
(h) Bleed left front brake line.
(1) Select ”FL LINE” on the TOYOTA hand-held tester.
(2) With ”FL LINE” turned ON with the TOYOTA hand-
held tester, depress the brake pedal and hold it to
bleed the left front brake caliper.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.
(i) w/ ABS & TRAC & VSC only:
Bleed rear brake line.
(1) Select ”RR LINE” on the TOYOTA hand-held tester.
(2) With ”RR LINE” turned ON with the TOYOTA hand-
held tester, bleed the left and right rear brake cali-
per.
(j) Disconnect the TOYOTA hand-held tester from DLC3.
(k) Clear the DTC (See page DI-505 ).
3. In case of using ABS actuator checker (SST):
BLEED HYDRAULIC BRAKE BOOSTER
HINT:
If the hydraulic brake booster has been disassembled, discon-

nect the brake line from the hydraulic brake booster or if the res-
ervoir becomes empty, bleed the hydraulic brake booster.
(a) Disconnect the 2 connectors from the hydraulic brake
booster.
F02821
Hydraulic Brake
Booster
Sub-wire Harness S (SST)
AIR BLEED
FRONT
REAR
BR-6
-BRAKE BRAKE FLUID
2142Author: Date:
2004 LAND CRUISER (RM1071U)
(b) Connect the actuator checker (SST) to the hydraulic
brake booster side wire harness via the sub-wire harness
(SST), as shown in the chart below.
SST 09990-00150, 09990-00480
HINT:
Connect the connector with the label of ”AIR BLEED” attached
to the connector of actuator checker.
(c) Connect the red cable of the checker to the battery posi-
tive (+) terminal and the black cable to the negative (-) ter-
minal.
(d) Turn the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.

(e) Turn the ignition switch ON, check that the pump stops af-
ter 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (d) and (e) again.
(f) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(g) Observe the procedure in step 4 and bleed the right and
left front wheel caliper.
(h) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.
F02823
F02824
F02825
-BRAKE BRAKE FLUID
BR-7
2143Author: Date:
2004 LAND CRUISER (RM1071U)
(i) Bleed right front brake line.
(1) Turn the selector switch of the actuator checker to
the ”FRONT RH” position.
(2) Push and hold in MAIN push switch, depress the
brake pedal and hold it to bleed the right front brake
caliper.
NOTICE:
Do not keep the MAIN switch pushed in for more than 10
sec. When operating it continuously, set the interval of
more than 20 sec.

(3) Repeat step (2) until there are no more air bubbles
in the fluid.
(j) Bleed left front brake line.
(1) Turn the selector switch of the actuator checker to
the ”FRONT LH” position.
(2) Push and hold in the MAIN push switch, depress the
brake pedal and hold it to bleed the left front brake
caliper.
NOTICE:
Do not keep the MAIN switch pushed in for more than 10
sec. When operating it continuously, set the interval of
more than 20 sec.
(3) Repeat step (2) until there are no more air bubbles
in the fluid.
(k) w/ ABS & TRAC & VSC only:
Bleed right rear brake line.
(1) Push and hold in the ”SUB LH” and ”SUB RH”
switches, bleed the right rear brake caliper.
NOTICE:
Do not keep the MAIN switch pushed in for more than 10
sec. When operating it continuously, set the interval of
more than 20 sec.
(2) Repeat step (1) until there are no more air bubbles
in the fluid.
F04458
BR-8
-BRAKE BRAKE FLUID
2144Author: Date:
2004 LAND CRUISER (RM1071U)
(l) Observe the procedure in step (k) and bleed left rear

brake line.
(m) Disconnect the actuator checker (SST) and sub-wire har-
ness (SST) from the actuator.
SST 09990-00150, 09990-00480
(n) Connect the 2 connectors to the hydraulic brake booster.
(o) Clear the DTC (See page DI-505 ).
4. BLEED BRAKE LINE
(a) Connect the vinyl tube to the brake caliper.
(b) Depress the brake pedal several times, then loosen the
bleeder plug with the pedal held down.
(c) At the point when fluid stops coming out, tighten the
bleeder plug, then release the brake pedal.
(d) Repeat (b) and (c) until all the air in the fluid has been bled
out.
(e) Repeat the above procedure to bleed the brake line for
each wheel.
Torque: 11 N·m (110 kgf·cm, 8 ft·lbf)
5. CHECK FLUID LEVEL IN RESERVOIR
(a) With the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(b) Remove the reservoir cap. Add brake fluid up to the
”MAX” line.
Fluid: SAE J1703 or FMVSS NO. 116 DOT3
BR0X9-02
F08309
Pedal Pad
Brake Pedal

Return Spring
Cowl Side Trim
Lower No. 1 Panel
LH Lower Panel
No. 2 Heater to Register Duct
ABS ECU or
ABS & BA & TRAC
& VSC ECU
N·m (kgf·cm, ft·lbf)
: Specified torque
Cushion
Stop Light Switch
20 (200, 14)
Hydraulic Brake Booster Assembly
MP Grease
Front Door Scuff Plate
5.0 (51, 44 in.·lbf)
Clevis Pin
Clip
-BRAKE BRAKE PEDAL
BR-1 1
2147Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
BR0XB-02
F06414
-BRAKE BRAKE PEDAL
BR-13
2149Author: Date:
2004 LAND CRUISER (RM1071U)

INSTALLATION
1. REASSEMBLY BRAKE PEDAL
(a) Install the pedal pad.
(b) Install the stop light switch cushion.
(c) Temporarily install the stop light switch to the pedal brack-
et.
(d) Install the return spring with cushion and pedal pad.
HINT:
Apply MP grease to the parts indicates by arrow (See page
BR-1 1).
2. INSTALL BRAKE PEDAL ASSEMBLY
Install the brake pedal assembly and temporarily fasten the 2
bolts.
3. INSTALL HYDRAULIC BRAKE BOOSTER
(See page BR-67 )
4. TIGHTEN 2 BOLTS OF BRAKE PEDAL BRACKET
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
5. AFTER INSTALLATION, FILL BRAKE RESERVOIR
WITH BRAKE FLUID AND BLEED BRAKE SYSTEM
(See page BR-4 )
6. CHECK FOR LEAKS
7. CHECK AND ADJUST BRAKE PEDAL
(See page BR-9 )
F09171
Stop Light Switch
Push Rod
Pedal Height
BR0JB-08
F02849
Pedal Freeplay

-BRAKE BRAKE PEDAL
BR-9
2145Author: Date:
2004 LAND CRUISER (RM1071U)
BRAKE PEDAL
ON-VEHICLE INSPECTION
1. CHECK PEDAL HEIGHT
Pedal height from asphalt sheet:
183.7 - 193.7 mm (7.232 - 7.626 in.)
If the pedal height is incorrect, adjust it.
2. IF NECESSARY, ADJUST PEDAL HEIGHT
(a) Remove the scuff plate, cowl side trim, lower No. 1 panel,
LH lower panel and No. 2 heater to register duct (See
page BO-81 ).
(b) Remove the steering wheel pad, steering wheel lower
No. 2 and No. 3 covers, steering wheel, combination
switch, column upper and lower covers, steering column
assembly and thrust stopper (See page SR-14 or
SR-29 ).
(c) Disconnect the connector from the stop light switch.
(d) Loosen the stop light switch lock nut and remove the stop
light switch.
(e) Loosen the push rod lock nut.
(f) Adjust the pedal height by turning the pedal push rod.
(g) Tighten the push rod lock nut.
Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
(h) Install the stop light switch.
(i) Connect the connector to the stop light switch.
(j) Push in the brake pedal 5 - 15 mm (0.20 - 0.59 in.), turn
the stop light switch to lock the nut in the position where

the stop light goes off.
(k) After installation, push in the brake pedal 5 - 15 mm (0.20
- 0.59 in.), check that stop light lights up.
(l) After adjusting the pedal height, check the pedal freeplay.
(m) Install the thrust stopper, steering column assembly, col-
umn upper and lower covers, combination switch, steer-
ing wheel, steering wheel lower No. 2 and No. 3 covers,
and steering wheel pad (See page SR-14 or SR-29 ).
(n) Install the No. 2 heater to register duct, LH lower panel,
lower No. 1 panel, cowl side trim and scuff plate (See
page BO-81 ).
3. CHECK PEDAL FREEPLAY
(a) Stop the engine and depress the brake pedal more than
40 times until there is no more pressure left in the booster.
(b) Push in the pedal by hand until the second point of resis-
tance begins to be felt, then measure the distance, as
shown.
Pedal freeplay: 1.0 - 6.0 mm (0.039 - 0.236 in.)
F02850
Pedal Reserve Distance
BR-10
-BRAKE BRAKE PEDAL
2146Author: Date:
2004 LAND CRUISER (RM1071U)
If incorrect, check the stop light switch clearance. If the clear-
ance is OK, then troubleshoot the brake system.
Stop light switch clearance: 1.9 mm (0.075 in.)
HINT:
The freeplay to the 1st point of resistance is due to the play be-
tween the clevis, pedal link and pin. It is 1.0 - 6.0 mm (0.039 -

0.236 in.) on the pedal.
4. CHECK PEDAL RESERVE DISTANCE
(a) Remove the floor carpet.
(b) Release the parking brake.
With the engine running, depress the pedal and measure
the pedal reserve distance, as shown.
Pedal reserve distance at 490 N (50 kgf, 110.1 lbf):
More than 116 mm (4.57 in.)
If the reserve distance is incorrect, troubleshoot the brake sys-
tem.
BR0XA-02
F06414
BR-12
-BRAKE BRAKE PEDAL
2148Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE HYDRAULIC BRAKE BOOSTER ASSEMBLY
(See page BR-60 )
2. REMOVE BRAKE PEDAL ASSEMBLY
(a) Disconnect the connector from the stop light switch.
(b) Remove the 2 bolts.
(c) Remove the brake pedal assembly.
3. DISASSEMBLY BRAKE PEDAL ASSEMBLY
(a) Remove the return spring with cushion.
(b) Remove the stop light switch.
(c) Remove the pedal pad.
BR12F-01
-BRAKE BRAKE SYSTEM
BR-1

2137Author: Date:
2004 LAND CRUISER (RM1071U)
BRAKE SYSTEM
PRECAUTION
z Care must be taken to replace each part properly as it could affect the performance of the brake
system and result in a driving hazard. Replace the parts with parts of the same part number or
equivalent.
z It is very important to keep parts and the area clean when repairing the brake system.
z If the vehicle is equipped with a mobile communication system, refer to the precautions in the
IN section.
BR0JJ-06
F05025
11 (110, 8)
74 (750, 54)
Bleeder Plug
Brake Caliper
Inner Pad
Clip
Boot
Piston Seal
Piston
Set Ring
Axle Hub
Disc
N·m (kgf·cm, ft·lbf)
: Specified torque
Lithium soap base glycol grease
Disc brake grease
Non-reusable part
z

30 (310, 22)
z Gasket
Outer Pad
Pad Retainer
Pad Retainer Clip
Anti-squeal Shim
Pad Retainer
Anti-squeal Shim
123 (1,250, 90)
x5
z Outer Bearing
Thrust Washer
Adjusting Nut
z Lock Washer
Lock Nut
z Gasket
Flange
z Snap Ring
z Grease Cap
x6
Plate Washer
33 (335, 24)
Cone Washer
Pin
64 (650, 47)
Outer Race
z Inner Bearing
Outer Race
z Oil seal
z

BR-18
-BRAKE FRONT BRAKE CALIPER
2154Author: Date:
2004 LAND CRUISER (RM1071U)
FRONT BRAKE CALIPER
COMPONENTS
BR0JL-03
F04972
Z09007
170mm
(6.70in)
50mm
(1.97in)
30mm
(1.18in)
BR0213
F04973
BR-20
-BRAKE FRONT BRAKE CALIPER
2156Author: Date:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE CYLINDER BOOT SET RINGS AND CYL-
INDER BOOTS
Using a screwdriver, remove the 4 cylinder boot set rings and
4 cylinder boots from the caliper.
2. REMOVE PISTONS FROM CYLINDER
(a) Prepare the wooden plate to hold the pistons.
(b) Place the plate between the pistons and insert a pad at
one side.

(c) Use compressed air to remove the pistons alternately
from the cylinder.
CAUTION:
Do not place your fingers in front of the piston when using
compressed air.
3. REMOVE PISTON SEALS FROM BRAKE CYLINDER
Using a screwdriver, remove the 4 piston seals from the cylin-
der.
F04980
BR0JM-06
F04981
F04982
-BRAKE FRONT BRAKE CALIPER
BR-21
2157Author: Date:
2004 LAND CRUISER (RM1071U)
INSPECTION
1. MEASURE PAD LINING THICKNESS
Using a ruler, measure the pad lining thickness.
Standard thickness: 11.5 mm (0.453 in.)
Minimum thickness: 1.0 mm (0.039 in.)
Replace the pad if the pad’s thickness is at the minimum or if
it shows signs of uneven wear.
2. MEASURE DISC THICKNESS
Using a micrometer, measure the disc thickness.
Standard thickness: 32.0 mm (1.260 in.)
Minimum thickness: 30.0 mm (1.181 in.)
Replace the disc if the thickness of the disc is at the minimum
thickness or less. Replace the disc or grind it on a lathe if it is
scored or is worn unevenly.

3. MEASURE DISC RUNOUT
Using a dial indicator, measure the disc runout at a position 10
mm (0.39 in.) from the out side edge.
Maximum disc runout: 0.07 mm (0.0028 in.)
If the bearing play and axle hub runout are not abnormal, re-
place the disc or grind it on an ”On-Car brake lathe”.
HINT:
Before measuring the runout, confirm that the front bearing pre-
load is within the specification (See page SA-16 ).
4. IF NECESSARY, REPLACE DISC
(a) Remove the front axle hub (See page SA-12 ).
(b) Remove the disc from the axle hub (See pageSA-13 ).
(c) Install a new disc and torque the 5 bolts.
Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
(d) Install the axle hub and adjust the front bearing preload
(See page SA-16 ).
BR0JO-06
-BRAKE FRONT BRAKE CALIPER
BR-23
2159Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-19 ).
HINT:
z After installation, fill the brake reservoir with brake fluid and bleed brake system (See page BR-4 ).
z Check for leaks.
BR0JN-04
BR-22
-BRAKE FRONT BRAKE CALIPER
2158Author: Date:

2004 LAND CRUISER (RM1071U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BR-20 ).
HINT:
Apply lithium soap base glycol grease to the parts indicated by the arrows (See page BR-18 ).
BR0TA-04
F04974
F04975
-BRAKE FRONT BRAKE CALIPER
BR-19
2155Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2. DISCONNECT BRAKE LINE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
Remove the 2 mounting bolts and remove the caliper.
Torque: 123 N·m (1,250 kgf·cm, 90 ft·lbf)
4. REMOVE CLIP AND 2 PINS
5. REMOVE 2 PAD RETAINER CLIPS
6. REMOVE 2 PADS, ANTI-SQUEAL SHIMS AND PAD
RETAINERS
BR0JH-03
F04971
Anti-squeal Shim

Pin
Pad Retainer Clip
Clip
Anti-squeal Shim
Pad Retainer
Pad Retainer
Outer Pad
Inner Pad
Disc brake grease
-BRAKE FRONT BRAKE PAD
BR-15
2151A uthor: Date:
2004 LAND CRUISER (RM1071U)
FRONT BRAKE PAD
COMPONENTS
BR0JI-1 1
F04993
F04994
F04995
BR-16
-BRAKE FRONT BRAKE PAD
2152A uthor: Date:
2004 LAND CRUISER (RM1071U)
REPLACEMENT
1. REMOVE FRONT WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad thickness through the caliper inspection hole
and replace the pads if they are not within the specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE CLIP AND 2 PINS

4. REMOVE 2 PAD RETAINER CLIPS
5. REMOVE 2 PADS, ANTI-SQUEAL SHIMS AND PAD
RETAINERS
NOTICE:
The pad retainer clip and clip can be used again provided
that they have sufficient rebound, no deformation, cracks
or wear, and have had all rust, dirt and foreign particles
cleaned off.
6. CHECK DISC THICKNESS AND DISC RUNOUT
(See page BR-21 )
7. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti-squeal shims must be
replaced together with the pad.
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the piston with a hammer handle or an equiva-
lent.
HINT:
z Always change the pads on one wheel at a time as there
is a possibility of opposite piston fling out.
z If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some brake fluid es-
cape.
(c) Install the 2 pad retainers to each caliper piston.
(d) Install the anti-squeal shim to each pad.
HINT:
Apply disc brake grease to both sides of the anti-squeal shims
(See page BR-15 ).
(e) Install the 2 pads.
HINT:

Apply disc brake grease to the pads indicated by the arrows
(See page BR-15 ).
-BRAKE FRONT BRAKE PAD
BR-17
2153A uthor: Date:
2004 LAND CRUISER (RM1071U)
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or the disc.
8. INSTALL 2 PAD RETAINER CLIPS AND 2 PINS
9. INSTALL CLIP
10. INSTALL FRONT WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
11. DEPRESS BRAKE PEDAL SEVERAL TIMES
12. CHECK THAT FLUID LEVEL IS AT MAX LINE
BR0K1-06
F05023
N·m (kgf·cm, ft·lbf) : Specified torque
Front Speed Sensor
8.0 (82, 71 in.·lbf)
13 (130, 9)
13 (130, 9)
BR-68
-BRAKE FRONT SPEED SENSOR
2204Author: Date:
2004 LAND CRUISER (RM1071U)
FRONT SPEED SENSOR
COMPONENTS
BR0K3-13
BR-70

-BRAKE FRONT SPEED SENSOR
2206Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-69 ).
HINT:
After installation, check the speed sensor signal (See page DI-505 ).
BR0K2-03
F05358
F05002
-BRAKE FRONT SPEED SENSOR
BR-69
2205Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
REMOVE SPEED SENSOR
(a) Disconnect the speed sensor connector.
(b) Remove the resin clip and 4 clamp bolts holding the sen-
sor harness from the steering knuckle and upper arm.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(c) Remove the speed sensor installation bolt and speed
sensor from the steering knuckle.
Torque: 8.0 N·m (82 kgf·cm, 71 in.·lbf)
BR0K8-20
F17443
Non-reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
z
zGasket
Hydraulic Brake

Booster Assembly
LH Lower Panel
Fluid Level Warning
Switch Connector
No. 2 Heater to
Register Duct
Cowl Side Trim
Lower No. 1 Panel
15 (155, 11)
15 (155, 11)
Pin
Clip
w/ ABS & BA &
TRAC & VSC Only:
Front Door Scuff Plate
5.0 (51, 44 in.·lbf)
ABS ECU or
ABS & BA &
TRAC & VSC
ECU
w/ ABS & BA & TRAC & VSC Only:
Master Cylinder Pressure Sensor Connector
15 (155, 11)
BR-58
-BRAKE HYDRAULIC BRAKE BOOSTER
2194Author: Date:
2004 LAND CRUISER (RM1071U)
COMPONENTS
F13209
Reservoir Set Screw

Accumulator Bracket
No. 1 Pump
Bracket
Actuator No. 1 Tube
Accumulator
zO-ring
Silencer Tube
Grommet
Piston
Cylinder Boot
Clevis
Reservoir Cap
No. 2 Pump
Bracket
Sleeve
Collar
Booster Pump Motor
Cushion
Actuator Hose
Non-reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
z
25 (260, 19)
Cushion
Fluid Level Warning Switch
Connector Clamp
Hydraulic Brake
Booster
Spring
15 (155, 11)

zWire Harness
Reservoir
1.7 (17.5, 15.2 in.·lbf)
54 (550, 36)
Washer
Master Cylinder
Pressure Sensor
81 (830, 60)
w/ ABS & BA
& TRAC & VSC:
z
-BRAKE HYDRAULIC BRAKE BOOSTER
BR-59
2195Author: Date:
2004 LAND CRUISER (RM1071U)