Mô hình tháp Big Ben, Anh. P1

Big Ben, England: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe

Before starting assembly:Writing the number of each section on its
back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)

/>
4

7

6

Indicates where sections should
be glued together.

7

1

2
7
5
View of completed model

7

*This model was designed for Papercraft and may differ from the original in some respects.

Assembly Instructions:Five A4 sheets(No.1 to No.5)

Parts 1 - 7

3

*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.

*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
8

Parts 1 + 2 + 3 + 6

Assembly Instructions
Mountain fold(dotted line)

Make a mountain fold.
Valley fold(dashed and dotted line)

Make a valley fold.
Scissors line(solid line)

Cut along the line.
Cut in line(solid line)

Cut along the line.

Tools and materials

Assembly tip

Glue
The glue spot(colored dot)
shows where to apply the glue.

Glue spot(Red dot)

Glue parts with the same number together.
10

Glue within the same part.

9

10

Glue spot(Blue dot)

Glue to the rear of the other part.

7
10

Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Parts 8 + 9

Before gluing, crease the paper along mountain fold and valley

fold lines and make sure rounded sections are nice and stiff.

Parts 4 + 5 + 7
Caution

These parts have
the same width.

10

Glue spot(Green dot)

Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.

1

Glue parts 8 and 9 to this base.


Big Ben, England: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe

20

Parts 1 - 10

12

12

12

12

Parts 1 - 13

Parts 1 - 13
Parts 14 - 18

18
19

11
12

24
19

17

21
13

23
24

16

15
14
22

2

Fold parts 19, 20, and 24 in two
and glue together. Cut these parts
after the glue has dried.


Big Ben, England: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe

30
30

30

28

30

Parts 1 - 18

29
29

29

29
32

32

27
31

Parts 21 - 24

26

32
32
32

25

Fold parts 31 and 32 in two
and glue together.
Cut these parts after the glue has dried.

3

Parts 25 - 28


Big Ben, England: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe

Parts 1 - 24

Parts 1 - 32

36

Parts 25 - 32

Parts 40 + 41

35

40

34
33

Parts 1 - 32

4

Parts 40 and 41 are reinforcements.
Glue near the center of parts 33 - 36.

41


Big Ben, England: Assembly Instructions

Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe

Parts 42 + 43
38

43

42

39

Parts 42 and 43 are reinforcements.
Glue near the center of the stand.

37

5

Finished!